bulb Hyundai Elantra GT 2017 User Guide

Maintenance
76
7
10. Install the socket in the assembly
by aligning the tabs on the sock-
et with the slots in the assembly.
Push the socket into the assem-
bly and turn the socket clockwise.
11. Reinstall the light assembly to the body of the vehicle.
Front side marker
Follow the steps 1 to 6 from the pre-
vious page.
7. Remove the socket from theassembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
8. Remove the bulb from the socket by pulling out the bulb.
9. Insert a new bulb. 10. Install the socket in the assembly
by aligning the tabs on the sock-
et with the slots in the assembly.
Push the socket into the assem-
bly and turn the socket clockwise.
11. Reinstall the light assembly to the body of the vehicle.
OGD072062N

777
Maintenance
Front fog light (if equipped)
Follow the steps 1 to 6 from the pre-
vious page.
7. Disconnect the power connectorfrom the socket.
8. Remove the bulb-socket from the housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing. 9. Install the new bulb-socket into the
housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock-
wise.
10. Connect the power connector to the socket.
Side repeater light bulb
replacement (if equipped)
If the light bulb is not operating, we
recommend that the vehicle be
checked by an authorized HYUNDAI
dealer.
✽ ✽NOTICE
A skilled technician should check or
repair the side repeater lamp.
Otherwise, it may damage related
parts (ex. outside mirror).
OGDE071055LOGD071030

Maintenance
78
7
Rear combination light bulb
replacement
(1) Back-up light
(2) Tail light
(3) Rear turn signal light
(4) Stop/tail light
(5) Side marker
Outside light
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Open the tailgate.
4. Loosen the light assembly retain- ing screws with a cross-tip screw-
driver.
5. Remove the rear combination light assembly from the body of the
vehicle. Rear turn signal light and stop/tail light
(Bulb type)
Follow the steps 1 to 5 from the pre-
vious page.
6. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
OGDE071031
OGDE071058
■Type A
■Type BOGD071032OGD071033

779
Maintenance
8. Insert a new bulb by inserting itinto the socket and rotating it until
it locks into place.
9. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
10. Reinstall the light assembly to the body of the vehicle.
Rear side marker (Bulb type)
Follow the steps 1 to 5 from the pre-
vious page.
6. Remove the socket from theassembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7. Remove the bulb from the socket by pulling out the bulb.
8. Insert a new bulb. 9. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
10. Reinstall the light assembly to the body of the vehicle.
OGD072063N

Maintenance
80
7
Stop/tail light and rear side marker
(LED type, if equipped)
If the LED light does not operate,
have the vehicle checked by an
authorized HYUNDAI dealer.
✽ ✽
NOTICE
A skilled technician should check or
repair the stop/tail and rear side
marker. Otherwise, it may damage
related parts of the vehicle.
Inside light
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Open the tailgate.
4. Remove the service cover using a flat-blade screwdriver. Tail light
(Bulb type)
5. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
OGD071034OGD071035
B
B
B
B
a
a
a
a
c
c
c
c
k
k
k
k
-
-
-
-
u
u
u
u
p
p
p
p




l
l
l
l
i
i
i
i
g
g
g
g
h
h
h
h
t
t
t
t
T
T
T
T
a
a
a
a
i
i
i
i
l
l
l
l

781
Maintenance
8. Install the socket in the assemblyby aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the service cover by putting it into the service hole. Back-up light (Bulb type)
5. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
6. Pull the bulb out of the socket.
7. Insert a new bulb into the socket.
8. Install the socket into the assem- bly by aligning the tabs on the
socket with the slots on the
assembly and turning the socket
clockwise.
9. Reinstall the light assembly to the body of the vehicle
Stop/tail light (LED type, if equipped)
If the LED light does not operate,
have the vehicle checked by an
authorized HYUNDAI dealer.
✽ ✽ NOTICE
A skilled technician should check or
repair the stop/tail light. Otherwise,
it may damage related parts of the
vehicle.
High mounted stop light
replacement
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Open the tailgate.
OGD071036

783
Maintenance
7. Remove the rear spoiler assembly. 8. Remove the high mounted stoplamp after removing the mounting
nuts.
9. Install a new lamp
10. Reinstall the rear spoiler and the tailgate upper trim in the reverse
order.License plate light bulb
replacement
1. Turn off the engine.
2. Disconnect the negative batterycable.
3. Remove the cover by pressing it as direction of the arrows.
4. Remove the bulb by pulling it straight out.
5. Install a new bulb.
6. Reinstall in the reverse order.
OGD072067NOGD072068NOGD071046

Maintenance
84
7
Interior light bulb replacement
1. Using a flat-blade screwdriver,
gently pry the lens from the interi-
or light housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap
the lens into place.
WARNING
Prior to working on the Interior
Lights, ensure that the “OFF”
button is depressed to avoid
burning your fingers or receiv-
ing an electric shock.
CAUTION
Use care not to dirty or damagelens, lens tab, and plastic hous-ings.
■ Map lamp■Luggage room lamp
■Room lamp
OGD071039/OMD070043/OGD071038/OGD071040/OTD079035
-
-
-
-



T
T
T
T
y
y
y
y
p
p
p
p
e
e
e
e




A
A
A
A
-
-
-
-



T
T
T
T
y
y
y
y
p
p
p
p
e
e
e
e




B
B
B
B
■
Sunvisor lamp

Specifications, Consumer information and Reporting safety defects
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
8-2
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Bulb wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Tires and wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Capacity/Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Recommended lubricants and capacities . . . . . . . . 8-5
Vehicle identification number (VIN) . . . . . . . . . . . 8-8
Vehicle certification label. . . . . . . . . . . . . . . . . . . . . 8-8
Tire specification and pressure label . . . . . . . . . . . 8-9
Engine number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Refrigerant label. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Consumer information. . . . . . . . . . . . . . . . . . . . . . 8-10
Reporting safety defects. . . . . . . . . . . . . . . . . . . . . 8-12
8

Specifications, Consumer information, Reporting safety defects
28
ItemSpecification
Displacement cu. in (cc) 121.9 (1999)
Bore x Stroke in. (mm) 3.19x3.81 (81x97)
Firing order 1-3-4-2
No. of cylinders 4, In-line
ENGINE BULB WATTAGE
DIMENSIONS
Iteminch (mm)
Overall length169.3 (4,300)
Overall width70.1 (1,780)
Overall height 57.9 (1,470)
Front treadP205/55R16Steel wheel61.0 (1,549)
Aluminum wheel61.2 (1,555)
P215/45R17Aluminum wheel61.0 (1,549)
Rear treadP205/55R16Steel wheel61.5 (1,562)
Aluminum wheel61.7 (1,568)
P215/45R17Aluminum wheel61.5 (1,562)
Wheelbase104.3 (2,650)
Light BulbWattageBulb type
Front
HeadlightsLow55H11
High55H7L
Day time running light55H7L
Front turn signal lights /
Position lights28/8PY28/8W
Front fog lights27881
Front side marker5W5WLL
Rear
Stop and tail lightsBulb28/8PY28/8W
LEDLEDLED
Rear turn signal lights 27PY27W
Tail lights 28/8PY28/8W
Rear side markerBulb5W5WLL
LEDLEDLED
Back-up lights 1616W
High mounted stop lightLEDLED
License plate lights5W5W
Interior
Map lamps8FESTOON
Room lamps8FESTOON
Luggage lamp8FESTOON
Vanity mirror lamps5FESTOON