ABS HYUNDAI ELANTRA N 2022 User Guide

Driving Your Vehicle6-36
NOTICE
Driving with wheels and tires with
different sizes may cause the ESC
system to malfunction. Before replacing
tires, make sure all four tires and wheels
are the same size. Never drive the
vehicle with different sized wheels and
tires installed.
WARNING
Don't use ESC SPORT mode or ESC OFF
while using a minispare tire or a tire
repair kit is in use!
ESC OFF usage
When Driving
The ESC OFF mode should only be used
brie
fly to help free the vehicle if stuck in
snow or mud, by temporarily stopping
operation of the ESC, to maintain wheel
torque.
To turn ESC off while driving, press the
ESC OFF button while driving on a flat
road surface.
NOTICE
To prevent damage to the transmission:
• Do not allow wheel(s) of one axle to
spin excessively while the ESC, ABS,
and parking brake warning lights
are displayed. The repairs would not
be covered by the vehicle warranty.
Reduce engine power and do not
spin the wheel(s) excessively while
these lights are displayed.
• When operating the vehicle on
a dynamometer, make sure the
ESC is turned off (ESC OFF light
illuminated).
Information
Turning the ESC off does not affect ABS
or standard brake system operation.
Drive mode selection
When the ESC is on, the characteristic
of ESC varies according to which drive
mode is selected by pressing the DRIVE
MODE or N1 or N2 button on the steering
wheel.
Mode
button Selected
mode Characteristic
of ESC
DRIVE
MODE
butt

on ECO mode NORMAL
NORMAL mode NORMAL
SPORT mode NORMAL
N button N mode SPORT
N CUSTOM mode NORMAL/
SPORT/OFF
For more details, refer to "Drive Mode
Integrated Control System" in this
chapter.
CN7 N HMA 6.indd 6-36 2021-09-14  9:42:28

07
7-77
• The following objects may not be detected:

- Sharp or slim objects, such as ropes,
chains or small poles.
- Objects, which tend to absorb sensor frequency, such as clothes,
spongy material or snow.
- Objects smaller than 100 cm (40 in.) in length and narrower than 14 cm
(6 in.) in diameter.
- Pedestrians, animals or objects that are very close to the ultrasonic
sensors
• Parking Distance Warning Indicators may be displayed differently from
the actual detected location when
the obstacle is located between the
sensors.
• Parking Distance Warning indicator may not occur sequentially depending
on vehicle speed or obstacle shape.
• If Reverse Parking Distance Warning needs repair, have the vehicle
inspected by an authorized HYUNDAI
dealer.
CN7 N HMA 7.indd 7-77 2021-09-14  9:45:13

09
9-23
Checking the Brake/Clutch Fluid
Level
OCN7N091036NOCN7N091036N
Check the fluid level in the reservoir
periodically. The fluid level should be
between MAX and MIN marks on the side
of the reservoir.
Before removing the reservoir cap and
adding brake fluid, clean the area around
the reservoir cap thoroughly to prevent
brake fluid contamination.
If the level is low, add fluid to the MAX
level. The level will fall with accumulated
mileage. This is a normal condition
associated with the wear of the brake
linings.
If the fluid level is excessively low, have
the system be checked by an authorized
HYUNDAI dealer.
Information
Use only the specified brake/clutch fluid.
Refer to “Recommended lubricants and
capacities” in chapter 2.
Information
Before removing the brake/clutch filler
cap, read the warning on the cap.
Information
Clean the filler cap before removing. Use
only DOT4 brake/clutch fluid from a
sealed container.
WARNING
Do not allow brake fluid to come in
contact with your eyes. If brake/clutch
fluid comes in contact with your eyes,
flush your eyes with clean water for
at least 15 minutes and get immediate
medical attention.
NOTICE
• Do not allow brake/clutch fluid to
contact the vehicle’s body paint, as
paint damage will result.
• Brake/clutch fluid, which has been
exposed to open air for an extended
time should never be used as its
quality cannot be guaranteed. It
should be disposed of properly.
• Don’t put in the wrong kind of fluid. A
few drops of mineralbased oil, such
as engine oil, in your brake system
can damage system parts.
• To maintain the best braking
performance and ABS/ESC
performance, have you use genuine
brake/clutch fluid that conform to
specifications.
(Standard : SAE J1704 DOT-4 LV,
ISO4925 CLASS-6 and FMVSS 116
DOT-4)
BRAKE/CLUTCH FLUID
CN7 N HMA 9.indd 9-23 2021-09-08  9:30:17

Maintenance9-32
Battery Recharging
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:
• Before performing maintenance or
recharging the battery, turn off all
accessories and place the ignition
switch to the LOCK/OFF position.
• Keep all flames, sparks, or smoking
materials away from the battery.
• Always work outdoors or in an area
with plenty of ventilation.
• Wear eye protection when checking
the battery during charging.
• The battery must be removed from
the vehicle and placed in a well
ventilated area.
• Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.
• Vehicle is equipped with the
Absorbent Glass Mat (AGM) battery.
Do not charge the AGM battery with
a general charger. It may damage
or explode the AGM battery. Only
charge the AGM battery with a
charger that has AGM battery
setting.
• The negative battery cable must
be removed first and installed last
when the battery is disconnected.
Disconnect the battery charger in the
following order:
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.
• Always use a genuine HYUNDAI
approved battery when you replace
the battery.
NOTICE
AGM battery (if equipped)
• Absorbent Glass Matt (AGM)
batteries are maintenance-free and
have the AGM battery be serviced
by an authorized HYUNDAI dealer.
For charging your AGM battery, use
only fully automatic battery chargers
that are specially developed for AGM
batteries.
• When replacing the AGM battery,
have you use parts for replacement
from an authorized HYUNDAI dealer.
• Do not open or remove the cap on
top of the battery. This may cause
leaks of internal electrolyte that
could result in severe injury.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
7 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to
the environment and human
health. Dispose of the battery
according to your local law(s) or
regulations.
Reset Items
Items should be reset after the battery
has been discharged or the battery has
been disconnected.
• Auto up/down window (See chapter 5)
• Sunroof (See chapter 5)
• Trip computer (See chapter 4)
• Climate control system (See chapter 5)
CN7 N HMA 9.indd 9-32 2021-09-08  9:30:22

09
9-33
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:
• Inspect your tires monthly for
proper inflation as well as wear
and damage.
• The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.
• Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.
• Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.
• ALWAYS replace tires with
the same type, size, brand,
construction and tread pattern
as each tire that was originally
supplied with this vehicle. Using
tires and wheels other than the
recommended sizes could cause
unusual handling characteristics,
poor vehicle control, or
negatively affect your vehicle’s
Anti-Lock Brake System (ABS)
resulting in a serious accident.
Information - Power Hop
When fully accelerating the vehicle
from standstill, a front tire oscillation
called “Power Hop“ of Elantra N
may occur due to the high torque
of engine and the characteristics of
high performance tire. This may
be affected by road condition and
temperatures.
Additionally it is a normal phenome
non in powerful front-wheel drive
vehicles. Elantra N will act on this
phenomenon with the traction control
in all ESC modes with the main focus
on high performance character.
TIRES AND WHEELS
CN7 N HMA 9.indd 9-33 2021-09-08  9:30:22

09
9-37
Tire Replacement
Tread wear indicatorTread wear indicator
OLMB073027OLMB073027
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 1/16 inch (1.6 mm) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the tread surface to
become level with the tread wear
indicators before replacing the tire.
WARNING
To reduce the risk of DEATH or
SERIOUS INJURY:
• Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, and traction.
• Always replace tires with the
same size as each tire that was
originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.
• Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, HYUNDAI recommends
that tires be replaced after six (6)
years of normal service.
• When replacing tires, it is
recommended to replace the
two front or two rear tires as a
pair. Replacing just one tire can
seriously affect your vehicle’s
handling. If only replacing one
pair of tires, it is recommended
to install the pair of new tires on
the rear axle.
• Heat caused by hot climates or
frequent high loading conditions
can accelerate the aging process.
Failure to follow this warning
may cause sudden tire failure,
which could lead to a loss of
vehicle control resulting in an
accident.
CN7 N HMA 9.indd 9-37 2021-09-08  9:30:23

Maintenance9-56
Engine compartment fuse panel
Type Fuse Name Fuse Rating Circuit Protected
FUSE POWER
OUTLET2 20
A Front Power Outlet
POWER
OUTLET3 20A Cigarette Lighter
VACUUM PUMP1 20A VACUUM PUMP, ESC
VACUUM PUMP2 10A Electronic Vacuum Pump
ECS 15A ECS Unit
E-LSD 20A LSD Control Module
E-CVVT3 20A ECM
E-CVVT2 20A ECM
E-CVVT1 40A E/R Junction Block (RLY.14)
DCT2 10A [G4FP] TCM
B+4 40AICU Junction Block (Fuse - F2, F25, F26, F34,
F43, F35 (IAU), F44, Power Window Relay)
AMS 10A Battery Sensor
TCU1 10A [M/T] Ignition Lock & Clutch Switch
FUEL PUMP 20A FUEL PUMP Motor
ABS1 40A ABS Control Module, ESP Control Module
ABS2 30AABS Control Module, ESP Control Module,
Multipurpose Check Connector
POWER
OUTLET1 40A E/R Junction Block (RLY.2)
WIPER 25A Wiper Motor
CN7 N HMA 9.indd 9-56
2021-09-08  9:30:27

09
9-57
Engine compartment fuse panel (PCB block) (Smartstream 2.5 GDI)
Type Fuse NameFuse Rating Circuit Protected
FUSE E
CS (15A)
15A ECS Unit
A/C 10A [G4FM] A/C Compressor
HORN 15A Horn, Horn Switch
IGN COIL 20A[G4FM/G4NA/G4FP] Ignition Coil #1~#4
[G4FG] Ignition Coil #1~#4
ECU3 10A PCM/ECM, [MT] IGN LOCK CLUTCH SW
SENSOR3 10A E/R Junction Block (RLY.8)
ECU2 15A PCM/ECM
SENSOR2 10A[G4FM] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11),
A/C Relay
[G4FG] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11)
[G4NA] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, Oil Pump Solenoid Valve, E/R
Junction Block (RLY.1/11)
[G4FP] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, RCV Control Solenoid Valve,
Cooling Fan Controller
[Theta 2 T-GDI] Oil Control Valve(Exhaust),
Electronic Water Pump, RCV, Cooling Fan, Purge
Control Solenoid Valve, A/C Comp RLY, Oil Level
Sensor, Canister Closing Valve, Active Exhaust
Valve
SENSOR1 15A Oxygen Sensor (UP/DOWN)
ABS3 10AABS Control Module, ESP Control Module,
Multipurpose Check Connector
ECU1 20A PCM/ECM
CN7 N HMA 9.indd 9-57
2021-09-08  9:30:28

09
9-59
Headlamp, Position Lamp,
Turn Signal Lamp and Daytime
Running Light Bulb Replacement
OCN7N091028NOCN7N091028N
(1) Headlamp (Low)
(2) Headlamp (High)
(3) Position lamp / Daytime running lamp (DRL)
(4) Turn signal lamp
(5) Side marker
Headlamp/Daytime running light (DRL) /
Position lamp (LED type)
If the LED lamp does not operate, have
the s
ystem inspected by an authorized
HYUNDAI dealer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
OCN7080043OCN7080043
Turn signal lamp
1. Open the hood.
2.

Disconnect the negative battery
cable.
3. Remove the socket from the assembly by turning the
socketcounterclockwise until the
tabs on the socket align with the slots
onthe assembly.
4. Remove the bulb from the socket by pressing it in and rotating
itcounterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the socket.
5. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
6. Install the socket in the assembly by aligning the tabs on the socket with
the slots in the assembly.
7. Push the socket into the assembly and turn the socket clockwise.
Lamps
If the LED lamp does not operate, have
the v
ehicle checked by an authorized
HYUNDAI dealer.
CN7 N HMA 9.indd 9-59 2021-09-08  9:30:28

09
9-61
Turn signal lamp (Outer lamp) (Bulb
type)
1. Open the trunk lid.
OCN7080045OCN7080045
2. Remove the service cover by pulling out the service cover.
OCN7080046OCN7080046
3. Loosen the assembly retaining nuts.
OCN7080047OCN7080047
4. Remove the rear combination light assembly from the body of the
vehicle.
OCN7N091034LOCN7N091034L[1] : Turn signal lamp
5. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
8. Install the socket in the assembly by aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
CN7 N HMA 9.indd 9-61 2021-09-08  9:30:29