ignition HYUNDAI ELANTRA N 2022 User Guide

Driving Your Vehicle6-38
VSM operation
When operating

When y
ou apply your brakes under
conditions which may activate the ESC,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your VSM is active.
Information
The VSM does not operate when:
• Driving through banked corners might
result in a ESC system shut down,
due to system self-diagnostics and an
assumption of a sensor failure.
In the next ignition cycle, the ESC
system is available again.
• Driving in reverse.
• The ESC OFF indicator light is on.
• The EPS (Electric power steering)
warning light (
) is on or blinks.
WARNING
If the ESC indicator light () or EPS
warning light () stays illuminated
or blinks, your vehicle may have a
malfunction with the VSM system.
When the warning light illuminates,
have your vehicle checked by an
authorized HYUNDAI dealer as soon as
possible.
NOTICE
Driving with wheels and tires with
different sizes may cause the VSM
system to malfunction. Before replacing
tires, make sure all four tires and wheels
are the same size. Never drive the
vehicle with different sized tires and
wheels installed.
WARNING
If ESC indicator light () or EPS
warning light () stays on or blinks,
your vehicle may have a malfunction
with the VSM system. When the
warning light illuminates, have your
vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
Driving with wheels and tires with
different sizes may cause the ESC system
to malfunction. Before replacing tires,
make sure all four tires and wheels are
the same size. Never drive the vehicle
with different sized tires and wheels
installed.
Hill-Start Assist Control (HAC)
The Hill-Start Assist Control (HAC)
helps prevent the vehicle from rolling
backwards when starting a vehicle from
a stop on a hill. The system operates the
brakes automatically for approximately
2 seconds and releases the brake after 2
seconds or when the accelerator pedal is
depressed.
WARNING
Always be ready to depress the
accelerator pedal when starting off on
a incline. The HAC activates only for
approximately 2 seconds.
NOTICE
• The HAC does not operate when the
shift lever is in P (Park) or N (Neutral)
• The HAC activates even though the
ESC (Electronic Stability Control) is
off but does not activate when the
ESC has malfunctioned.
CN7 N HMA 6.indd 6-38 2021-09-14  9:42:29

06
6-67
Chain Installation
When installing AutoSock (fabric snow
chain
), follow the manufacturer’s
instructions and mount them as tightly
as possible. Drive slowly (less than 20
mph (30 km/h)) with chains installed. If
you hear the chains contacting the body
or chassis, stop and tighten them. If they
still make contact, slow down until the
noise stops. Remove the AutoSock(fabric
snow chain) as soon as you begin
driving on cleared roads.When mounting
AutoSock (fabric snow chain), park the
vehicle on level ground away from traffic.
Turn on the vehicle Hazard Warning
Flasher and place a triangular emergency
warning device behind the vehicle (if
available).Always place the vehicle in
P (Park), apply the parking brake and
turn off the engine before installing tire
chains.
NOTICE
When using AutoSock (fabric snow
chain):
• Wrong size chains or improperly
installed chains can damage your
vehicle's brake lines, suspension,
body and wheels.
• If you hear noise caused by chains
contacting the body, retighten the
chain to prevent contact with the
vehicle body.
• To prevent body damage, retighten
the chains after driving 0.3-0.6 miles
(0.5-1.0 km).
Winter Precautions
Use high quality ethylene glycol
coolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because it
helps prevent corrosion in the cooling
system, lubricates the water pump and
prevents freezing. Be sure to replace or
replenish your coolant in accordance
with the maintenance schedule in
chapter 8. Before winter, have your
coolant tested to assure that its freezing
point is sufficient for the temperatures
anticipated during the winter.
Change to "winter weight" oil if
necessary
In some climates it is recommended that
a lower viscosity "winter weight" oil be
used during cold weather. See chapter 8
for recommendations. If you aren't sure
what weight oil you should use, consult
an authorized HYUNDAI dealer.
Check battery and cables
Winter puts additional burdens on the
battery system. Visually inspect the
battery and cables as described in
chapter 8. The level of charge in your
battery can be checked by an authorized
HYUNDAI dealer or a service station.
Check spark plugs and ignition
system
Inspect your spark plugs as described in
chapter 8 and replace them if necessary.
Also check all ignition wiring and
components to be sure they are not
cracked, worn or damaged in any way.
CN7 N HMA 6.indd 6-67 2021-09-14  9:42:42

Emergency Situations8-4
Jump starting can be dangerous if done
incorrectly. Follow the jump starting
procedure in this section to avoid serious
injury or damage to your vehicle. If in
doubt about how to properly jump start
your vehicle, have a service technician or
towing service do it for you.
WARNING
To prevent SERIOUS INJURY or DEATH
to you or bystanders, always follow
these precautions when working near
or handling the battery:
Always read and follow
instructions carefully when
handling a battery.
Wear eye protection designed
to protect the eyes from acid
splashes.
Keep all flames, sparks, or
smoking materials away from
the battery.
Hydrogen is always present
in battery cells, is highly
combustible, and may explode
if ignited.
Keep batteries out of reach of
children.
Batteries contain sulfuric acid
which is highly corrosive. Do
not allow acid to contact your
eyes, skin or clothing. If acid gets into your eyes, flush your
eyes with clean water for at least 15
minutes and get immediate medical
attention. If acid gets on your skin,
thoroughly wash the area. If you feel
pain or a burning sensation, get medical
attention immediately.
•
When lifting a plastic-cased battery,
excessive pressure on the case may
cause battery acid to leak. Lift with a
battery carrier or with your hands on
opposite corners.
• Do not attempt to jump start your
vehicle if your battery is frozen.
• NEVER attempt to recharge the
battery when the vehicle’s battery
cables are connected to the battery.
• The electrical ignition system works
with high voltage. NEVER touch
these components with the engine
running or when the Engine Start/
Stop button in the OFF position.
JUMP STARTING
CN7 N HMA 8.indd 8-4 2021-09-06  4:18:06

Maintenance9-14
Engine Oil and Filter
The engine oil and filter should be
changed at the intervals specified in the
maintenance schedule. If the vehicle
is being driven in severe conditions,
more frequent oil and filter changes are
required.
Drive Belts
Inspect all drive belts for evidence
of cuts, cracks, excessive wear or oil
saturation and replace if necessary. Drive
belts should be checked periodically
for proper tension and adjusted as
necessary.
Information
When you are inspecting the belt, turn the
engine off.
Fuel Filter
A clogged-up fuel filter may limit the
vehicle driving speed, damage the
emission system, and cause the hard
starting. When a considerable amount
of foreign substances are accumulated
in the fuel tank, the fuel filter should be
replaced.
Upon installing a new fuel filter, operate
the engine for several minutes, and
check the connections for any leakages.
Fuel filters should be installed by an
authorized HYUNDAI dealer.
Fuel Lines, Fuel Hoses and
Connections
Check the fuel lines, fuel hoses and
connections for leakage and damage.
Have an authorized HYUNDAI dealer
replace any damaged or leaking parts
immediately.
Vapor Hose and Fuel Filler Cap
The vapor hose and fuel filler cap should
be inspected at those intervals specified
in the maintenance schedule. Make sure
a new vapor hose or fuel filler cap is
correctly replaced.
Air Cleaner Filter
A genuine HYUNDAI air cleaner filter
is recommended when the filter is
replaced.
Spark Plugs
Make sure to install new spark plugs of
the correct heat range.
When assembling parts, be sure to
wipe out foreign substances inside
and outside of the boot bottom of the
ignition coil and the insulator of the
spark plug with a soft cloth to prevent
contamination of the spark plug
insulator.
WARNING
Do not disconnect and inspect spark
plugs when the engine is hot. You may
burn yourself.
Cooling System
Check cooling system components, such
as radiator, coolant reservoir, hoses and
connections for leakage and damage.
Replace any damaged parts.
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
CN7 N HMA 9.indd 9-14 2021-09-08  9:30:15

Maintenance9-30
WARNING
To prevent SERIOUS INJURY or DEATH
to you or bystanders, always follow
these precautions when working near
or handling the battery:
Always read and follow
instructions carefully when
handling a battery.
Wear eye protection designed
to protect the eyes from acid
splashes.
Keep all flames, sparks, or
smoking materials away from
the battery.
Hydrogen is always present
in battery cells, is highly
combustible, and may explode
if ignited.
Keep batteries out of reach of
children.
Batteries contain sulfuric acid
which is highly corrosive. Do
not allow acid to contact your
eyes, skin or clothing. If acid gets into your eyes, flush your
eyes with clean water for at least 15
minutes and get immediate medical
attention. If acid gets on your skin,
thoroughly wash the area. If you feel
pain or a burning sensation, get medical
attention immediately.
•
When lifting a plastic-cased battery,
excessive pressure on the case may
cause battery acid to leak. Lift with a
battery carrier or with your hands on
opposite corners.
• Do not attempt to jump start your
vehicle if your battery is frozen.
• NEVER attempt to recharge the
battery when the vehicle’s battery
cables are connected to the battery.
• The electrical ignition system works
with high voltage. NEVER touch
these components with the engine
running or when the Engine Start/
Stop button is in the ON position.
• Do not allow the (+) and (-) jumper
cables to touch. It may cause sparks.
• The battery may rupture or explode
when you jump start with a low or
frozen battery.
• Leaked battery electrolyte due to
repeated driving on sharp curves
(for example, on circuits) may cause
safety problem. Avoid repeated
driving on sharp curves.
WARNING
CALIFORNIA PROPOSITION 65
WARNING
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to the
State of California to cause cancer,
birth defects and reproductive harm.
Batteries also contain other chemicals
known to the State of California
to cause cancer. Wash hands after
handling.
BATTERY
CN7 N HMA 9.indd 9-30 2021-09-08  9:30:21

Maintenance9-32
Battery Recharging
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:
• Before performing maintenance or
recharging the battery, turn off all
accessories and place the ignition
switch to the LOCK/OFF position.
• Keep all flames, sparks, or smoking
materials away from the battery.
• Always work outdoors or in an area
with plenty of ventilation.
• Wear eye protection when checking
the battery during charging.
• The battery must be removed from
the vehicle and placed in a well
ventilated area.
• Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.
• Vehicle is equipped with the
Absorbent Glass Mat (AGM) battery.
Do not charge the AGM battery with
a general charger. It may damage
or explode the AGM battery. Only
charge the AGM battery with a
charger that has AGM battery
setting.
• The negative battery cable must
be removed first and installed last
when the battery is disconnected.
Disconnect the battery charger in the
following order:
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from the negative battery terminal.
3. Unhook the positive clamp from the positive battery terminal.
• Always use a genuine HYUNDAI
approved battery when you replace
the battery.
NOTICE
AGM battery (if equipped)
• Absorbent Glass Matt (AGM)
batteries are maintenance-free and
have the AGM battery be serviced
by an authorized HYUNDAI dealer.
For charging your AGM battery, use
only fully automatic battery chargers
that are specially developed for AGM
batteries.
• When replacing the AGM battery,
have you use parts for replacement
from an authorized HYUNDAI dealer.
• Do not open or remove the cap on
top of the battery. This may cause
leaks of internal electrolyte that
could result in severe injury.
By jump starting
After a jump start from a good battery,
drive the vehicle for 20-30 minutes
before it is shutoff. The vehicle may
not restart if you shut it off before the
battery had a chance to adequately
recharge. See “Jump Starting” in chapter
7 for more information on jump starting
procedures.
Information
An inappropriately disposed
battery can be harmful to
the environment and human
health. Dispose of the battery
according to your local law(s) or
regulations.
Reset Items
Items should be reset after the battery
has been discharged or the battery has
been disconnected.
• Auto up/down window (See chapter 5)
• Sunroof (See chapter 5)
• Trip computer (See chapter 4)
• Climate control system (See chapter 5)
CN7 N HMA 9.indd 9-32 2021-09-08  9:30:22

09
9-55
Engine compartment fuse panel
Type Fuse NameFuse Rating Circuit Protected
MIDI
FUSE
-3 ALT
180A[G4FM/G4FG/G4NA] Alternator, (Fuse - F33, F34,
F35, F37)
[G4FP] Alternator, (Fuse - F33, F34, F35, F37)
MDPS1 100A MDPS Unit
MIDI
FUSE-2 COOLING
FAN2 80A [G4FP] Cooling Fan Controller
EOP 60A Electronic Oil Pump
RR HTD 50A Rear Glass Heated
MIDI
FUSE-1 B+5
60APCB Block (Engine Control Relay, Fuse - F1, F2,
F3, F4, F6)
B+1 60A ICU Junction Block (IPS2/IPS5/IPS6/IPS7/IPS14)
B+2 60AICU Junction Block (IPS1/IPS4/IPS8/IPS9/IPS10/
IPS13)
B+3 50AICU Junction Block (Fuse - F13, F14, F22, F23,
F32,F40, F41, Long Term Load Latch Relay)
BLOWER 40A BLOWER Motor, Multipurpose Check Connector
IG1 40A E/R Junction Block (RLY.4/6), Ignition Switch
IG2 40A E/R Junction Block (RLY.3/5), Ignition Switch
DCT1 60A TCU
PTC
HEATER 50A PTC HEATER
CN7 N HMA 9.indd 9-55
2021-09-08  9:30:27

Maintenance9-56
Engine compartment fuse panel
Type Fuse Name Fuse Rating Circuit Protected
FUSE POWER
OUTLET2 20
A Front Power Outlet
POWER
OUTLET3 20A Cigarette Lighter
VACUUM PUMP1 20A VACUUM PUMP, ESC
VACUUM PUMP2 10A Electronic Vacuum Pump
ECS 15A ECS Unit
E-LSD 20A LSD Control Module
E-CVVT3 20A ECM
E-CVVT2 20A ECM
E-CVVT1 40A E/R Junction Block (RLY.14)
DCT2 10A [G4FP] TCM
B+4 40AICU Junction Block (Fuse - F2, F25, F26, F34,
F43, F35 (IAU), F44, Power Window Relay)
AMS 10A Battery Sensor
TCU1 10A [M/T] Ignition Lock & Clutch Switch
FUEL PUMP 20A FUEL PUMP Motor
ABS1 40A ABS Control Module, ESP Control Module
ABS2 30AABS Control Module, ESP Control Module,
Multipurpose Check Connector
POWER
OUTLET1 40A E/R Junction Block (RLY.2)
WIPER 25A Wiper Motor
CN7 N HMA 9.indd 9-56
2021-09-08  9:30:27

09
9-57
Engine compartment fuse panel (PCB block) (Smartstream 2.5 GDI)
Type Fuse NameFuse Rating Circuit Protected
FUSE E
CS (15A)
15A ECS Unit
A/C 10A [G4FM] A/C Compressor
HORN 15A Horn, Horn Switch
IGN COIL 20A[G4FM/G4NA/G4FP] Ignition Coil #1~#4
[G4FG] Ignition Coil #1~#4
ECU3 10A PCM/ECM, [MT] IGN LOCK CLUTCH SW
SENSOR3 10A E/R Junction Block (RLY.8)
ECU2 15A PCM/ECM
SENSOR2 10A[G4FM] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11),
A/C Relay
[G4FG] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11)
[G4NA] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, Oil Pump Solenoid Valve, E/R
Junction Block (RLY.1/11)
[G4FP] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, RCV Control Solenoid Valve,
Cooling Fan Controller
[Theta 2 T-GDI] Oil Control Valve(Exhaust),
Electronic Water Pump, RCV, Cooling Fan, Purge
Control Solenoid Valve, A/C Comp RLY, Oil Level
Sensor, Canister Closing Valve, Active Exhaust
Valve
SENSOR1 15A Oxygen Sensor (UP/DOWN)
ABS3 10AABS Control Module, ESP Control Module,
Multipurpose Check Connector
ECU1 20A PCM/ECM
CN7 N HMA 9.indd 9-57
2021-09-08  9:30:28