check engine light HYUNDAI ELANTRA N 2022 Owner's Manual

Driving Your Vehicle6-48
NGS (N Grin Shift)
Controls engine / transmission to
maximum performance when pressing
NGS button on the steering wheel
remote control in situations where rapid
acceleration is required.
Functional description and
operating conditions
OCN7N061188 OCN7N061188
When NGS button is pressed:
• Automatically shifts to the lowest allowable gear (Automatic shifting is
not performed in manual shift mode)
• Turbo is in overboost mode (number can be added as well)
• N Grin Shift is available for 20 Seconds
• N Grin Shift can be reused 40 seconds later after using the function for 20
seconds
N Grin Shift will turn off during operation
or will not operate when:
• Changing Drive-mode during N Grin Shift operation
• Engine check light is on
• Transmission high temperature (overheating) lights on
• Transmission malfunction
• Shift lever is in P/ R/ N
• Using N Grin Shift within 40 seconds after using the function for 20
seconds
ActivatedActivatedNon-operatingNon-operating
OJSN040333OJSN040333OOSN061052NOOSN061052N
CAUTION
• The driver should hold the
responsibility to safely drive and
control the vehicle when using N
Grin Shift.
• Do not attempt dangerous driving
while using N Grin Shift.
• It is recommended to use after
vehicle break-in and continuous
use of N Grin Shift can overload
the vehicle components such as
transmission, engine and drive shaft.
CN7 N HMA 6.indd 6-48 2021-09-14  9:42:32

06
6-53
Launch control on and off (For
Manual transmission)
1. Select N mode with ‘N’ button (N mode indicator will illuminate on
the cluster) or select SPORT+ for the
engine mode in CUSTOM mode.
2. Check that the ESC mode is ESC SPORT mode or ESC OFF. If not, press
ESC OFF button to set the ESC mode
to ESC SPORT mode or ESC OFF.
(Electronic Stability Control (ESC)
does not operate when ESC OFF.)
3. Select 'Performance Options → Launch Control' to set engine RPM from the
Infotainment system screen. After
setting RPM, press 'Activate’.
4. Align the steering wheel straight
5. Depress the clutch pedal.
6. Shift to 1st gear.
7. While depressing the clutch pedal with your left foot, quickly and fully
depress the accelerator pedal with
your right foot. Launch control will
be in the ready state. The message
'Launch Control Ready' will appear on
the cluster. If necessary, adjust engine
rpm with +/- switch on the steering
wheel.
8. A smooth, quick release of the clutch pedal within 8 seconds,
while maintaining full depression
of the accelerator pedal will initiate
launching of the vehicle. The message
'Launch Control Active' will appear on
the cluster.
9. Control will deactivate when the accelerator pedal is released.
Launch control on and off (For Dual
clutch transmission)
1. Select N mode with 'N' button (N-mode indicator lights up on
cluster) or select SPORT+ for the
engine mode in custom mode.
2. Check that the ESC mode is ESC SPORT or ESC OFF. If not, press
button to set the ESC mode to ESC
SPORT or ESC OFF.(Indicator lights on
the cluster)(Vehicle dynamic control
device does not operate when ESC
OFF.)
3. Put the transmission gear on 'D'(driving) or 'M' (manual mode)
position.(driver must shift by yourself
when manual mode is selected.)
4. In Launch Control tab of Navigation's Performance Options, select rpm
and press ‘Activate’ button.(N mode
→ Performance Option → Launch
Control) (button lights on when
activated)
5. Align the steering wheel straight.
6. Press brake pedal to maximum with your left foot.
7. When you press the brake pedal with your left foot and quickly press and
hold accelerator pedal with your right
foot, you are ready for launch control.
When it is ready, the text “Launch
Control Ready” is displayed. RPM
value can be adjusted with +/- switch
on the steering wheel.
8. Release your foot gently off the brake pedal within 8 seconds to launch
the vehicle, keeping accelerator
pedal fully pressed. Launch Control
is activated and the text“ Launch
Control Active” is displayed.
9. Launch control is deactivated when you release accelerator pedal.
CN7 N HMA 6.indd 6-53 2021-09-14  9:42:35

06
6-55
Shift Light
Normal modeNormal mode
OBC3N060029 OBC3N060029
N modeN mode
OCN7N061258NOCN7N061258N
When engine is operating in a high
RPM area, it is indicated on the cluster
according to the corresponding engine
RPM.
As the engine RPM approaches to the
limit, each of shift lights on both sides,
and when all lights blinks in red or alert
alarm sound, it is time to perform up-
shift immediately.
In the “Shift light” tab of the
performance option, you can set which
mode displays shift light and select
target shift RPM.
(N mode → Performance options → Shift
light)
OCN7N061241LOCN7N061241L
1. Press ‘Shift light’ tab in Performance options.
2. Select drive mode to activate shift indicator. (ECO/NORMAL/SPORT/N/
CUSTOM)
3. Set up target RPM by pressing ‘< (Left)’ or ‘> (Right)’.
(6000 RPM ~ 6700 RPM)
4. Check ‘Alert sound’ to choose whether or not to execute.
5. Press ‘Reset RPM’ to reset the target RPM speed.
• Engine speed change notification is sent before engine speed reaches to
the set value to shift at set target RPM
speed.
CN7 N HMA 6.indd 6-55 2021-09-14  9:42:35

06
6-65
The severe weather conditions of winter
quickly wear out tires and cause other
problems. To minimize winter driving
problems, you should take the following
suggestions:
Snow or Icy Conditions
You need to keep sufficient distance
between your vehicle and the vehicle in
front of you.
Apply the brakes gently. Speeding, rapid
acceleration, sudden brake applications,
and sharp turns are potentially
very hazardous practices. During
deceleration, use engine braking to the
fullest extent. Sudden brake applications
on snowy or icy roads may cause the
vehicle to skid.
To drive your vehicle in deep snow, it
may be necessary to use snow tires or to
install tire chains on your tires.
Always carry emergency equipment.
Some of the items you may want to carry
include tire chains, tow straps or chains,
a flashlight, emergency flares, sand, a
shovel, jumper cables, a window scraper,
gloves, ground cloth, coveralls, a blanket,
etc.
Snow tires
WARNING
Snow tires should be equivalent in size
and type to the vehicle’s standard tires.
Otherwise, the safety and handling of
your vehicle may be adversely affected.
If you mount snow tires on your vehicle,
make sure to use radial tires of the same
size and load range as the original tires.
Mount snow tires on all four wheels
to balance your vehicle’s handling in
all weather conditions. The traction
provided by snow tires on dry roads
may not be as high as your vehicle's
original equipment tires. Check with
the tire dealer for maximum speed
recommendations.
Information
Do not install studded tires without
first checking local, state and municipal
regulations for possible restrictions against
their use.
WINTER DRIVING
CN7 N HMA 6.indd 6-652021-09-14  9:42:41

07
7-37
Information
• After the engine is turned off, Safe Exit
Warning operates approximately for 3
minutes, but turns off immediately if
the doors are locked.
• Images or colors may appear
differently depending on the instrument
panel specifications or theme.
Safe Exit Warning Malfunction
and Limitations
Safe Exit Warning malfunction
OTM070099NOTM070099N
When Safe Exit Warning is not working
properly, the ‘Check Blind-Spot Safety
system’ warning message will appear on
the cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized HYUNDAI dealer.
CN7 N HMA 7.indd 7-37 2021-09-14  9:44:44

Driver Assistance System7-38
OTM070100NOTM070100N
When the side view mirror warning
light is not working properly, the ‘Check
side view mirror warning light’ warning
message will appear on the cluster
for several seconds, and the master
(
) warning light will illuminate on
the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized HYUNDAI dealer.
Safe Exit Warning disabled
OCN7N071098LOCN7N071098L
When the rear bumper around the rear
corner radar or sensor is covered with
foreign material, such as snow or rain,
or installing a trailer or carrier, it can
reduce the detecting performance and
temporarily limit or disable Safe Exit
Warning.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’ warning
message will appear on the cluster.
Safe Exit Warning will operate properly
when such foreign material or trailer,
etc., is removed, and then the engine is
restarted.
If Safe Exit Warning does not operate
properly after it is removed, have the
vehicle inspected by an authorized
HYUNDAI dealer.
CN7 N HMA 7.indd 7-38 2021-09-14  9:44:44

08
8-3
If you Have a Flat Tire While
Driving
If a tire goes flat while you are driving:
• Take your foot off the accelerator pedal and let the vehicle slow down
while driving straight ahead. Do not
apply the brakes immediately or
attempt to pull off the road as this
may cause loss of vehicle control
resulting in an accident. When the
vehicle has slowed to such a speed
that it is safe to do so, brake carefully
and pull off the road. Drive off the
road as far as possible and park on
firm, level ground. If you are on a
divided highway, do not park in the
median area between the two traffic
lanes.
• When the vehicle is stopped, press the hazard warning flasher button, move
the shift lever into P (Park), and apply
the parking brake, and set the Engine
Start/Stop button in the OFF position.
• Have all passengers get out of the vehicle. Be sure they all get out on the
side of the vehicle that is away from
traffic.
• When changing a flat tire, follow the instructions provided later in this
chapter.
IF THE ENGINE WILL NOT
START
If the Engine Doesn’t Turn Over
or Turns Over Slowly
• Be sure the shift lever is in N (Neutral) or P (Park). The engine starts only
when the shift lever is in N (Neutral) or
P (Park).
• Check the battery connections to be sure they are clean and tight.
• Turn on the interior light. If the light dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to start it.
This could cause damage to your vehicle.
See instructions for “Jump Starting”
provided in this chapter.
CAUTION
Push or pull starting the vehicle may
cause the catalytic converter to
overload which can lead to damage to
the emission control system.
If the Engine Turns Over
Normally but Doesn’t Start
Check the fuel level and add fuel if
necessary.
If the engine still does not start, have
your vehicle checked by an authorized
HYUNDAI dealer.
CN7 N HMA 8.indd 8-3 2021-09-06  4:18:06

08
8-5
Jump starting procedure
1. Position the vehicles close enough that the jumper cables will reach, but
do not allow the vehicles to touch.
2. Avoid fans or any moving parts in the engine compartment at all times, even
when the vehicles are turned off.
3. Turn off all electrical devices such as radios, lights, air conditioning, etc.
Put the vehicle in P (Park), and set the
parking brakes. Turn both vehicles
OFF.
OCN7N081001NOCN7N081001N
4. Open the engine hood.
5. Connect the jumper cables in the exact sequence shown in the
illustration. First connect one jumper
cable to the red, positive (+) jumper
terminal of your vehicle (1).
6. Connect the other end of the jumper cable to the red, positive (+) battery/
jumper terminal of the assisting
vehicle (2).
7. Connect the second jumper cable to the black, negative (-) battery/jumper
terminal of the assisting vehicle (3). 8. Connect the other end of the second
jumper cable to the black, negative (-)
chassis ground of your vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over the
battery when making connections.
CAUTION
Before jump starting, make sure to
correctly identify the positive (+) and
negative (-) terminals to avoid reverse
polarity connections.
WARNING
Do not connect the jumper cable to
the negative (-) jumper terminal of the
discharged battery. A spark could cause
the battery to explode and lead to a
personal injury or vehicle damage.
9. Operate your vehicle for at least 30 minutes of driving or at least
60 minutes of engine running at
idle before shutting off the engine.
Without sufficient time to charge
the battery the vehicle will reoccur
another no start. You can also visit
your nearest dealer to request the
battery be charged and tested.
If your vehicle will not start after a few
attempts, it probably requires servicing.
In this event please seek qualified
assistance. If the cause of your battery
discharging is not apparent, have your
vehicle checked by an authorized
HYUNDAI dealer.
CN7 N HMA 8.indd 8-5 2021-09-06  4:18:06

08
8-11
NOTICE
If any of the below happens, have
the system checked by an authorized
HYUNDAI dealer.
1. The Low Tire Pressure Telltale/ TPMS Malfunction Indicator does not
illuminate for 3 seconds when the
Engine Start/Stop button is set to
the ON position or engine is running.
2. The TPMS Malfunction Indicator remains illuminated after blinking for
approximately 1 minute.
3. The Low Tire Pressure Position Telltale remains illuminated.
Low Tire Pressure Telltale
Low Tire Pressure Position and
Tire Pressure Telltale
OCN7080057LOCN7080057L
When the tire pressure monitoring
system warning indicators are
illuminated and a warning message
displayed on the cluster LCD display,
one or more of your tires is significantly
under-inflated. The Low Tire Pressure
Position Telltale will indicate which
tire is significantly underinflated by
illuminating the corresponding position
light.
CN7 N HMA 8.indd 8-11 2021-09-06  4:18:12

Tires and Wheels ........................................................................\
.................. 9-33Tire Care ........................................................................\
.......................................... 9-34
Recommended Cold Tire Inflation Pressures ....................................................... 9-34
Check Tire Inflation Pressure ........................................................................\
......... 9-35
Tire Rotation ........................................................................\
................................... 9-35
Wheel Alignment and Tire Balance ....................................................................... 9-36
Tire Replacement ........................................................................\
........................... 9-37
Wheel Replacement ........................................................................\
....................... 9-38
Tire Traction ........................................................................\
.................................... 9-38
Tire Maintenance..................................................................\
.................................. 9-38
Tire Sidewall Labeling ........................................................................\
.................... 9-38
Tire Terminology and Definitions ........................................................................\
...9-41
All Season Tires ........................................................................\
...............................9-44
Summer Tires ........................................................................\
.................................9-44
Snow Tires......................................................................\
.........................................9-44
Radial-Ply Tires ........................................................................\
............................... 9-45
Low Aspect Ratio Tires ........................................................................\
................... 9-45
Fuses ...................................................................\
.......................................... 9-47Instrument Panel Fuse Replacement ....................................................................9-48
Engine Compartment Panel Fuse Replacement ..................................................9-49
Fuse/Relay Panel Description........................................................................\
........9-50
Light Bulbs ........................................................................\
............................9-58Headlamp, Position Lamp, Turn Signal Lamp and Daytime Running
Light Bulb Replacement ........................................................................\
................ 9-59
Side Repeater Lamp Replacement ...................................................................... 9-60
Rear Combination Lamp Bulb Replacement ....................................................... 9-60
High Mounted Stop Lamp Replacement .............................................................. 9-62
License Plate Light Bulb Replacement .................................................................9-63
Interior Light Bulb Replacement ........................................................................\
...9-63
Appearance Care ........................................................................\
.................9-65Exterior Care ........................................................................\
................................... 9-65
Interior Care ........................................................................\
.................................... 9-70
Emission Control System ........................................................................\
..... 9-73
California Perchlorate Notice ...................................................................... 9-76
9
CN7 N HMA 9.indd 9-22021-09-08  9:30:13