coolant HYUNDAI ELANTRA N 2022 Owners Manual

2-7
02
2.0 T-GDi2.0 T-GDi
The actual engine compartment in the vehicle may differ from the illustration.
OCN7N091001 OCN7N091001
1. Engine coolant reservoir .......................9-18
2. Brake/clutch fluid reservoir ................. 9-22
3. Air cleaner ............................................. 9-24
4. Engine oil dipstick ................................. 9-15
5. Engine oil filler cap ................................ 9-156. Windshield washer fluid reservoir ....... 9-23
7. Fuse box ................................................ 9-48
8. Battery ................................................... 9-30
9. Engine coolant cap ................................ 9-19
ENGINE COMPARTMENT
CN7 N HMA 2.indd 2-7
2021-09-14  9:30:00

Vehicle Information, Consumer Information and Reporting Safety Defects2-12
RECOMMENDED LUBRICANTS AND CAPACITIES
To help achieve proper engine and powertrain performance and durability, use only
lubricants of the proper quality. The correct lubricants also help promote engine
efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
Lubricant Volume
Engine oil
*1 *2
(drain and refill) Recommends 5.49 US qt. (5.2 ℓ) SAE 0W-30 API SN PLUS/SP or
ILSAC GF-6
*3
Manual transmission fluid
1.9 ~ 2.0 US qt.
(1.8 ~ 1.9 ℓ) HK SYN MTF 70W (SK)
SPIRAX S6 GHME 70W MTF
(H.K.SHELL)
GS MTF HD 70W (GS CALTEX)
(API GL-4, SAE 70W, TGO-9)
Dual clutch
transmission
fluid Gear oil
3.4 ~ 3.6 US qt.
(3.3 ~ 3.4 ℓ) GS WDCTF HD G (WDGO-1)
Control oil 2.58 ~ 2.64 US qt.
(2.45 ~ 2.5 ℓ) GS WDCTF HD H (WDHO-1)
Coolant 8.12 US qt.
(7.68 ℓ) Mixture of antifreeze and water
(Phosphate-based Ethylene glycol
coolant for aluminum radiator)
Brake/clutch fluid
*40.74 ~ 0.85 US qt. (0.7 ~ 0.8 ℓ) DOT-4
Fuel 12.42 US gal.
(47 ℓ) Refer to “Fuel requirements” in the
chapter 1.
*1 : Refer to the recommended SAE viscosity numbers on the next page.
*2 : Engine oils labeled Energy Conserving Oil are now available. Along with other additional
benefits, they contribute to fuel economy by reducing the amount of fuel necessary
to overcome engine friction. Often, these improvements are difficult to measure in
everyday driving, but in a year’s time, they can offer significant cost and energy savings.
*3 : Requires < API SN PLUS (or above) Full synthetic> grade engine oil. If a lower grade
engine oil (mineral oil including Semi-synthetic) is used, then the engine oil and engine
oil filter must be replaced as indicated severe maintenance condition.
*4 : For the best performance of braking and ABS/ESC functions, you should use genuine
brake fluid that conform to standards. (Standards: SAE J1704 DOT-4 LV, ISO4925 CLASS-6
and FMVSS116 DOT-4)
CN7 N HMA 2.indd 2-12
2021-09-14  9:30:01

4
Instrument Cluster ........................................................................\
................. 4-4Instrument Cluster Control ........................................................................\
.............. 4-5Instrument panel illumination ........................................................................\
....... 4-5
Gauges and Meters ........................................................................\
.......................... 4-5 Speedometer .....................................................................\
.................................... 4-5
Tachometer .....................................................................\
....................................... 4-6
Engine Coolant Temperature Gauge .................................................................... 4-6
Fuel Gauge ........................................................................\
..................................... 4-7
Outside Temperature Gauge ........................................................................\
......... 4-8
Odometer .....................................................................\
.......................................... 4-8
Distance to empty ........................................................................\
......................... 4-9
Fuel economy (Normal mode) ........................................................................\
...... 4-9
CUSTOM mode settings ........................................................................\
................ 4-9
Transmission Shift Indicator ........................................................................\
.......... 4-10
Warning and Indicator Lights ........................................................................\
......... 4-11 Air Bag Warning Light ........................................................................\
................... 4-11
Seat Belt Warning Light ........................................................................\
................ 4-11
Parking Brake & Brake Fluid Warning Light ......................................................... 4-11
Anti-lock Brake System (ABS) warning light ....................................................... 4-12
Electronic Brake Force Distribution System Warning Light ............................... 4-12
Malfunction Indicator Lamp (MIL) ....................................................................... 4-13
Charging System Warning Light ........................................................................\
..4-14
Engine Oil Pressure Warning Light ......................................................................4-14
Low Fuel Level Warning Light ........................................................................\
...... 4-15
Master Warning Light ........................................................................\
................... 4-15
Low Tire Pressure Warning Light ........................................................................\
.4-16
Electronic Stability Control (ESC) Indicator Light ..............................................4-16
Electronic Stability Control (ESC) OFF Indicator Light ....................................... 4-17
Forward safety warning light ........................................................................\
...... 4-17
Immobilizer Indicator Light (with smart key) ..................................................... 4-17
Turn Signal Indicator Light ........................................................................\
...........4-18
Exterior Light Warning Light ........................................................................\
........4-18
LED headlight warning light ........................................................................\
.........4-18
High Beam Indicator Light ........................................................................\
...........4-18
Light ON Indicator Light ........................................................................\
...............4-18
Low Beam Indicator Light ........................................................................\
............4-19
High Beam Assist indicator light ........................................................................\
..4-19
Forward safety warning light ........................................................................\
.......4-19
Lane Keep Assist Indicator Light ........................................................................\
.4-19
Cruise Indicator Light ........................................................................\
...................4-19
SPORT Mode Indicator Light ........................................................................\
........4-19
ECO Mode Indicator Light ........................................................................\
........... 4-20
4. Instrument Cluster
CN7 N HMA 4.indd 4-1 2021-09-14  9:31:56

4-4
Instrument Cluster
Normal mode (Type A)Normal mode (Type A)
N mode (Type B)N mode (Type B)
The actual cluster in the vehicle may differ from the illustration.
For more details, refer to the “Gauges and Meters” in this chapter.
OOSN041001N/OCN7N041130NOOSN041001N/OCN7N041130N
INSTRUMENT CLUSTER
1. Tachometer
2. Speedometer
3. Engine coolant temperature gauge 4. Fuel gauge
5. Shift light
CN7 N HMA 4.indd 4-4
2021-09-14  9:32:02

Instrument Cluster4-6
Tachometer
Normal modeNormal mode
OCN7040007OCN7040007
N modeN mode
OCN7N041133NOCN7N041133N
The tachometer indicates the
approximate number of engine
revolutions per minute (RPM).
Use the tachometer to select the correct
shift points and to prevent lugging and/
or over-revving the engine.
NOTICE
Do not operate the engine within the
tachometer’s RED ZONE. This may
cause severe engine damage.
Engine Coolant Temperature Gauge
Normal modeNormal mode
OCN7040009OCN7040009
N modeN mode
OCN7N041134NOCN7N041134N
This gauge indicates the temperature
of the engine coolant when the Engine
Start/Stop button is in the ON position.
NOTICE
If the gauge pointer moves beyond
the normal range area toward the “H”
position, it indicates overheating that
may damage the engine.
Do not continue driving with an
overheated engine. If your vehicle
overheats, refer to “If the Engine
Overheats” in chapter 8.
WARNING
Never remove the radiator cap when
the engine is hot. The engine coolant is
under pressure and could cause severe
burns. Wait until the engine is cool
before adding coolant to the reservoir.
CN7 N HMA 4.indd 4-6 2021-09-14  9:32:10

Instrument Cluster4-24
Low fuel
This warning message is displayed if the
fuel tank is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will
come on.
It is recommended to look for the nearest
fueling station and refuel as soon as
possible.
Engine Overheated (if equipped)
This warning message is displayed
when the engine coolant temperature
is above 248°F (120°C). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” in chapter 8.
Check headlight (High) (if equipped)
This warning message is displayed if the
headlamps are not operating properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check headlight (Low) (if equipped)
This warning message is displayed if
the headlamp (Low) are not operating
properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating
Check turn signal (if equipped)
This warning message is displayed if
the turn signal lamps are not operat-
ing properly. A lamp may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check brake light (if equipped)
This warning message is displayed if the
stop lamps are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check daytime running light (if
equipped)
This warning message is displayed
if the daytime running lights are not
operating properly. A lamp may need to
be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check high mounted brake light (if
equipped)
This warning message is displayed if
the high mounted stop lamp are not
operating properly. A lamp may need to
be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check headlight LED (if equipped)
This warning message is displayed
if there is a problem with the LED
headlight. We recommend that you have
the vehicle inspected by an authorized
HYUNDAI dealer.
CN7 N HMA 4.indd 4-24 2021-09-14  9:32:43

06
6-45
When the Drive Mode is set
to ECO mode, the engine and
transmission control logic are
changed to maximize fuel
efficiency.
• When the ECO mode is selected, the ECO indicator will illuminate.
• If the vehicle is set to ECO mode, when the engine is turned OFF and
restarted, the Drive Mode setting will
change to NORMAL mode.
Information
Fuel efficiency depends on the driver’s
driving habit and road condition.
When ECO mode is activated:
• The acceleration response may be slightly r
educed as the accelerator
pedal is depressed moderately.
• The air conditioner performance may be limited.
• The engine noise may get louder.
The above situations are normal
conditions when ECO mode is activated,
to improve fuel efficiency. Limitation of ECO mode operation:
If the following conditions occur while
E

CO mode is operating, the system
operation is limited even though there is
no change in ECO indicator.
• When the coolant temperature is low:
The system will be limited until engine
performance becomes normal.
• When driving up a hill: The system will be limited to gain
power when driving uphill because
engine torque is restricted.
The system will be limited due to the
shift location.
• When the accelerator pedal is deeply depressed for a few seconds:
The system will be limited, judging
that the driver wants to speed up.
CN7 N HMA 6.indd 6-45 2021-09-14  9:42:31

Driving Your Vehicle6-64
Driving in Flooded Areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel hub.
Drive through any water slowly. Allow
adequate stopping distance because
brake performance may be reduced.
After driving through water, dry the
brakes by gently applying them several
times while the vehicle is moving slowly.
Highway Driving
Tires
Adjust the tire inflation, as specified.
Under-inflation may overheat or damage
the tires.
Do not install worn-out or damaged tires,
which may reduce traction or adversely
affect vehicle handling. This could lead
to sudden tire failure that may cause
loss of vehicle control resulting in an
accident.
Information
Never over-inflate your tires above the
maximum inflation pressure, as specified
on your tires.
Fuel, engine coolant and engine oil
Driving at higher speeds on the highway
consumes more fuel and is less efficient
than driving at a slower, more moderate
speed. Maintain a moderate speed in
order to conserve fuel when driving on
the highway.
Be sure to check both the engine coolant
level and the engine oil before driving.
Drive belt
A loose or damaged drive belt may
overheat the engine.
CN7 N HMA 6.indd 6-64 2021-09-14  9:42:41

06
6-67
Chain Installation
When installing AutoSock (fabric snow
chain
), follow the manufacturer’s
instructions and mount them as tightly
as possible. Drive slowly (less than 20
mph (30 km/h)) with chains installed. If
you hear the chains contacting the body
or chassis, stop and tighten them. If they
still make contact, slow down until the
noise stops. Remove the AutoSock(fabric
snow chain) as soon as you begin
driving on cleared roads.When mounting
AutoSock (fabric snow chain), park the
vehicle on level ground away from traffic.
Turn on the vehicle Hazard Warning
Flasher and place a triangular emergency
warning device behind the vehicle (if
available).Always place the vehicle in
P (Park), apply the parking brake and
turn off the engine before installing tire
chains.
NOTICE
When using AutoSock (fabric snow
chain):
• Wrong size chains or improperly
installed chains can damage your
vehicle's brake lines, suspension,
body and wheels.
• If you hear noise caused by chains
contacting the body, retighten the
chain to prevent contact with the
vehicle body.
• To prevent body damage, retighten
the chains after driving 0.3-0.6 miles
(0.5-1.0 km).
Winter Precautions
Use high quality ethylene glycol
coolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because it
helps prevent corrosion in the cooling
system, lubricates the water pump and
prevents freezing. Be sure to replace or
replenish your coolant in accordance
with the maintenance schedule in
chapter 8. Before winter, have your
coolant tested to assure that its freezing
point is sufficient for the temperatures
anticipated during the winter.
Change to "winter weight" oil if
necessary
In some climates it is recommended that
a lower viscosity "winter weight" oil be
used during cold weather. See chapter 8
for recommendations. If you aren't sure
what weight oil you should use, consult
an authorized HYUNDAI dealer.
Check battery and cables
Winter puts additional burdens on the
battery system. Visually inspect the
battery and cables as described in
chapter 8. The level of charge in your
battery can be checked by an authorized
HYUNDAI dealer or a service station.
Check spark plugs and ignition
system
Inspect your spark plugs as described in
chapter 8 and replace them if necessary.
Also check all ignition wiring and
components to be sure they are not
cracked, worn or damaged in any way.
CN7 N HMA 6.indd 6-67 2021-09-14  9:42:42

Driving Your Vehicle6-68
Use approved window washer anti-
freeze in system
To keep the water in the window washer
system from freezing, add an approved
window washer anti-freeze solution in
accordance with instructions on the
container.
Window washer anti-freeze is available
from an authorized HYUNDAI dealer
and most auto parts outlets. Do not
use engine coolant or other types of
antifreeze as these may damage the
paint finish.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged position.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or
if the brakes are wet. If there is a risk
the parking brake may freeze, apply
it only temporarily while you put the
gear selector lever in P and block the
rear wheels so the car cannot roll. Then
release the parking brake.
Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in severe winter conditions where this
may happen, you should periodically
check underneath the car to be sure the
movement of the front wheels and the
steering components is not obstructed.
Don't place foreign objects
or materials in the engine
compartment
Placement of foreign object or materials
which prevent cooling of the engine, in
the engine compartment, may cause a
failure or combustion. The manufacturer
is not responsible for the damage caused
by such placement.
To keep locks from freezing
To keep the locks from freezing, squirt
an approved de-icer fluid or glycerine
into the key opening. If a lock is covered
with ice, squirt it with an approved de-
icing fluid to remove the ice. If the lock
is frozen internally, you may be able to
thaw it out by using a heated key. Handle
the heated key with care to avoid injury.
CN7 N HMA 6.indd 6-68 2021-09-14  9:42:42