jacking HYUNDAI GENESIS G70 2019 Owners Manual

3-50
Convenient features of your vehicle
• The power trunk can be operat-
ed when the engine is not run-
ning. However, the power trunk
operation consumes a large
amount of electic power.
To prevent the battery from
being discharged, do not oper-
ate it excessively (e.g. more than
5 times repeatedly).
• To prevent the battery from
being discharged, do not leave
the power trunk in the open
position for a long time.
• Do not modify or repair any part
of the power trunk by yourself.
This must be done by an author-
ized retailer of Genesis Branded
products.
• When jacking up the vehicle to
change a tire or repair the vehi-
cle, do not operate the power
trunk. This could cause the
power trunk to operate improp-
erly.
• In cold and wet climates, the
power trunk may not work prop-
erly due to freezing conditions.
Automatic reversal
During power opening and closing if
the power trunk is blocked by an
object or part of the body, the power
trunk will detect the resistance.
If resistance is detected while open-
ing or closing the power trunk, the
trunk will stop and move in the oppo-
site direction.
However, in some instances the
automatic reversal system may not
detect the object if it is too soft or is
very thin, or if the trunk is almost fully
closed near the latched position.
Caution should be taken to prevent
any objects from obstructing the
trunk opeining.If the automatic reversal feature
operates more than 2 times while
attempting to open or close the
trunk, the power trunk may stop at
that position. If this occurs, carefully
close the trunk manually, and then
try to operate the power trunk auto-
matically again.
NOTICE
OIK048433
Never intentionally place any
object or part of your body in
the path of the power trunk to
make sure the automatic rever-
sal operates.
WARNING
Do not put heavy objects on the
power trunk before you operate
the power trunk feature.
Additional weight may damage
the operation of the system.
CAUTION

6-15
What to do in an emergency
6
If it is hard to loosen the tire hold-
down wing bolt by hand, you can
loosen it easily using the jack handle.
1. Put the jack handle (1) inside of
the tire hold-down wing bolt.
2. Turn the tire hold-down wing bolt
counterclockwise with the jack
handle.
Changing Tires
A vehicle can slip or roll off of a
jack causing serious injury or
death to you or those nearby.
Take the following safety pre-
cautions:
•Never place any portion of
your body under a vehicle that
is supported by a jack.
•NEVER attempt to change a
tire in the lane of traffic.
ALWAYS move the vehicle
completely off the road on
level, firm ground away from
traffic before trying to change
a tire. If you cannot find a level,
firm place off the road, call a
towing service for assistance.
•Be sure to use the jack pro-
vided with the vehicle.
•ALWAYS place the jack on the
designated jacking positions
on the vehicle and NEVER on
the bumpers or any other part
of the vehicle for jacking sup-
port.
WARNING
OIK067038L
Do not touch luggage
room metal surface
while the engine is
operating or hot.
Doing so could result in serious
personal injury.
Turn the engine off and wait
until it cools down or wear
gloves to remove the spare tire
from the luggage room.
WARNING

6-16
What to do in an emergency
Follow these steps to change your
vehicle's tire:
1. Park on a level, firm surface.
2. Shift the vehicle to P (Park, auto-
matic transmission vehicle) or
neutral (for manual transmission
vehicle), apply the parking brake,
and press the Engine Start/Stop
button to the OFF position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tire
from the vehicle.
5. Block both the front and rear of the
tire diagonally opposite of the tire
you are changing.6. Loosen the wheel lug nuts coun-
terclockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground.7. Place the jack at the designated
jacking position under the frame
closest to the tire you are chang-
ing. The jacking positions are
plates welded to the frame with
two notches. Never jack at any
other position or part of the vehi-
cle. Doing so may damage the
side seal molding or other parts of
the vehicle.
OIK067034LOIK067035L
•Do not start or run the engine
while the vehicle is on the
jack.
•Do not allow anyone to remain
in the vehicle while it is on the
jack.
•Keep children away from the
road and the vehicle.