lock HYUNDAI GENESIS G80 2021 Owners Manual

7-67
7
Maintenance
Fuse NameFuse ratingCircuit Protected
E-SHIFTER 110A Electronic ATM Shift Lever
SMART KEY 110A Start/Stop Button Switch
MODULE 710A Multi-View Camera Module, Sunroof Motor, Head-Up Display, Cooling Fan Controller,
Passenger Lumbar Support Unit
MODULE 810A Smart Key Control Module, BCM
MODULE 220A
Smart Key Control Module, Overhead Console Lamp, BCM, AMP
Digital Clock, Keyboard, I-BOX, A/V & Navigation Head Unit, Front Monitor, Electronic ATM Shift Lever,
Front Wireless Charger, Front Power Outlet & Cigarette Lighter, Multi-View Camera Module,
Metal Core Block (PCB #1 - Power Outlet Relay)
P/SEAT DRV 130A Driver IMS Control Module, Driver Power Seat Relay Box
P/SEAT PASS 130A Passenger Power Seat Relay Box
DOOR LAMP10A Driver/Passenger Door Module, Rear Door Module LH/RH
BRAKE SWITCH10A Smart Key Control Module, Stop Lamp Switch
A/CON20A Metal Core Block (PCB #1 - Blower Relay), Ionizer, CO2 Sensor, A/C Control Module

7-69
7
Maintenance
Engine compartment fuse panel
Fuse NameFuse ratingCircuit Protected
ALT200AAlternator, Multifuse (BATT) - B+2/ B+5/ MDPS 1,
Fuse - P/SEAT DRV 2/ P/SEAT RR/ SEAT LUMBAR/ ESC 1/ ESC 2
B+160A IGPM (Fuse - BRAKE SWITCH, E-SHIFTER 1 Leak Current Autocut Device (Fuse - INTERIOR LAMP/
MULTI MEDIA 1/ MEMORY 3), IPS 1)
B+360A IGPM (Fuse - SMART KEY 1/ SMART KEY 2/ MODULE 1/ B/A HORN, IPS 2/IPS 3/IPS 5/IPS 7)
B+460A IGPM (Fuse - DOOR LAMP/ MODULE 9/ MODULE 10, IPS 4/ IPS6/ IPS)
B+660A Metal Core Block (PCB #1 Fuse - ECU 3/ IG2/ MODULE 1)
B+780A Metal Core Block (PCB #2 Fuse - HORN/ ACC/ EPB 1/ EPB 2/ B/UP LAMP)
B+260A IGPM (Fuse - P/HANDLE/ P/WDW LH/ P/SEAT DRV 1/ P/SEAT PASS 1/ S/HEATER PASS/ POWER
OUTLET 3/ SUNROOF/ P/DOOR DRV/ P/DOOR PASS)
B+580A Metal Core Block (PCB #1 Fuse - BLOWER/ DEICER/ H/LAMP WASHER/ H/LAMP HI SOL)
MDPS 1125A MDPS Unit
C/FAN80A Cooling Fan Controller
P/SEAT
RR30A Not Used
ESC 240A ESC Module, Multipurpose Check Connector
ESC 140A ESC Module, Multipurpose Check Connector
P/SEAT DRV 225A Driver IMS Control Module, Driver Power Seat Switch, Driver Power Seat Relay Box
VACUUM
PUMP40A Vacuum Pump Relay
WIPER 130A Wiper Motor

7-70
Maintenance
Fuse NameFuse ratingCircuit Protected
S/HEATER
DRV25A Driver CCS Module, Driver Seat Warmer Control Module
4WD30A 4WD ECM
PRESAFETY
SEAT BELT 130A Pre-Active Seat Belt Module
PRESAFETY
SEAT BELT 230A Pre-Active Seat Belt Module
IG230A IG2 Relay
ECU 330A Engine Control Relay
MODULE 110A 4WD ECM, Smart Cruise Control Radar, Active Air Flap
WIPER 210A Metal Core Block (PCB #2 - Wiper Relay)
WASHER20A Washer Relay
SENSOR 210A G6DN : Oxygen Sensor #1/#2/#3/#4, Variable Intake Solenoid Valve #1/#2
G8BE : Oxygen Sensor #1/#2/#3/#4, Electronic Thermostat
G6DP : Oxygen Sensor #1/#2/#3/#4, RCV Control Solenoid Valve
SENSOR 110A Oil Control Valve #1/#2/#3/#4, Canister Close Valve, Purge Control Solenoid Valve
SENSOR 310A Electronic Thermostat, Rear Junction Block (Fuel Pump Relay)
SENSOR 410A G8BE : Camshaft Position Sensor #1/#2/#3/#4
IGN COIL15A G6DN : Ignition Coil #1/#2/#3/#4/#5/#6
G8BE : Ignition Coil #1/#2/#3/#4/#5/#6/#7/#8
G6DP : Ignition Coil #1/#2/#3/#4/#5/#6
ECU 420A ECM
H/LAMP
HI SOL10A H/LAMP HI SOL Relay

7-71
7
Maintenance
Fuse NameFuse ratingCircuit Protected
DEICER20A Metal Core Block (PCB #2 - Front Deicer Relay)
H/LAMP
WASHER25A Head Lamp Washer Relay
A/CON 210A A/C Control Module
BLOWER40A Blower Relay
IG140A IG1 Relay
START30A E/R Junction Block (RLY. 2 - Start Relay)
ECU 115A ECM
TCU 120A TCM
ESC 310A ESC Module
MODULE 310A Smart Cruise Control Radar, Active Air Flap, 4WD ECM
MDPS 210A MDPS Unit, Steering Angle Sensor
SENSOR 510A G6DP : Brake Boost Vacuum Pressure Sensor Switch
HORN20A Horn Relay
ECU 210A ECM
TCU 215A TCM, Transmission Range Switch, P/N Relay, B/UP Lamp Relay
EPB 215A Electronic Parking Brake Module
EPB 115A Electronic Parking Brake Module
B/UP LAMP10A B/UP Lamp Relay
ACC40A ACC Relay

7-73
7
Maintenance
Fuse NameFuse ratingCircuit Protected
P/TRUNK30A Power Trunk Lid Control Module
P/DOOR 15A Rear Door Latch RH RR RH
DOOR LOCK 215A Passenger Door Module
P/DOOR RR LH15A Rear Door Latch LH
AIR BAG15A Air Bag Relay
SPARE 110A Spare Fuse
P/SEAT PASS 225A Passenger Power Seat Relay Box
F/LID10A Fuel Lid Open Relay, Crash Pad Switch
ECS15A ECS Unit
DOOR LOCK 110A Driver Door Module
SPARE 615A Spare Fuse
TRUNK10A Trunk Lid Relay, Power Trunk Module Buzzer
S/HEATER
RR RH20A Rear Seat Warmer Control Module RH
FOG LAMP
RR10A Not Used
AMP25A AMP
S/HEATER
RR LH20A Rear Seat Warmer Control Module LH
P/WDW RH30A Passenger Power Window Module, Rear Power Window Module RH
F/PUMP20A Fuel Pump Relay
RR HTD40A Rear Defogger Relay
Trunk fuse panel

7-75
7
Maintenance
Fuse NameFuse ratingCircuit Protected
B+9100A
Rear Junction Block (Fuse - RR HTD/ P/TRUNK/ ECS/ F/LID/
P/DOOR RR RH/ DR LOCK 2/ P/DOOR RR LH/ AMP/
P/SEAT PASS 2/ DR LOCK 1/ TRUNK/ S/HEATER RR RH/
S/HEATER RR LH/ P/WDW RH/ F/PUMP/ AIR BAG)
B+880AMetal Core Block (PCB #2 Fuse - TCU/ ECU 1/ START/ IG 1)
AMS10ABattery Sensor
Trunk fuse panel

7-78
Maintenance
✽ ✽
NOTICE
We recommend that the headlamp
aiming be adjusted after an accident
or after the headlamp assembly is
reinstalled at an authorized retailer
of Genesis Branded products.
Headlamp
1. Turn off the engine.
2. Open the hood.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the connector (A) and
pull the BI-FUNCTION lamp.
5. Connect the BI-FUNCTION lamp
to the cable and install the con-
nector (A).
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.Push the socket into the assembly
and turn the socket clockwise.
If the headlamp (LED) does nut oper-
ate, have the vehicle checked by an
autorized retailer of Genesis
Branded products.
ODH073064L
A
A

7-79
7
Maintenance
Turn signal light
1. Turn off the engine.
2. Open the hood.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly
and turn the socket clockwise.
If the turn signal light (LED) does not
operate, have the vehicle checked by
an authorized retailer of Genesis
Branded products.Position and front fog lamp/
bulbs
If the LED lamp does not operate,
have the vehicle checked by an
authorized retailer of Genesis
Branded products.
Side repeater lamp replace-
ment
If the LED lamp does not operate,
have the vehicle checked by an
authorized retailer of Genesis
Branded products.
ODH073066L ■Bulb type
ODH073040

7-80
Maintenance
Rear combination light bulb
replacement
Type A
(1) Stop/tail light
(2) Turn signal light
(3) Back-up light
(4) Side marker
Type B
(1) Stop/tail light
(2) Turn signal light
(3) Back-up light
(4) Side marker
Rear turn signal lamp
Type A
1. Open the trunk lid.
2. Open the service cover.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.ODH073041 ■Type A
ODH073041 ■Type BODH073067L

7-81
7
Maintenance
5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
7. Install the service cover by putting
it into the service hole.
Type B
If the LED lamp does not operate,
have the vehicle checked by an
authorized retailer of Genesis
Branded products.
Back up lamp
Type A
1. Open the trunk.
2. Loosen the retaining screw of the
trunk lid cover and then remove
the cover.
3. Remove the socket from the
assembly by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb by pulling it
straight out.
5. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.6. Install the socket into the assem-
bly by aligning the tabs on the
socket with the slots in the assem-
bly. Push the socket into the
assembly and turn the socket
clockwise.
7. Reinstall the trunk lid cover by
pushing in the screw.
Type B
If the LED lamp does not operate,
have the vehicle checked by an
authorized retailer of Genesis
Branded products.
Stop and tail lamp
If the lamp does not operate, have
the vehicle checked by an authorized
retailer of Genesis Branded prod-
ucts.
ODH073068L