ignition Hyundai Getz 2004 Repair Manual

1- 42 FEATURES OF YOUR HYUNDAI
B260S01B-GAT
DIESEL PRE-HEAT
INDICATOR
LIGHT-AMBER
(Diesel Engine)
The indicator light illuminates amber
when the ignition switch is placed at
the "ON" position. The engine can be
started after the pre-heat indicator light
goes off. The illuminating time varies
with the water temperature, air tem-
perature and battery condition.
NOTE:
If the engine were not started 10
seconds after the preheating is com-
pleted, turn the ignition key once
more to the "LOCK" position, and
then to the "ON" position, in order
to preheat again.
B260T01TB-GAT
ELECTRIC POWER
STEERING SYSTEM
(EPS) WARNING LIGHT
(Not all models)
This indicator light comes on about 4
seconds after the ignition key is turned
to the "ON" position or after the engine
is started, it will go out.
This light also comes on when the EPS
has some troubles. If it comes on while
driving, have your vehicle inspected by
an authorized Hyundai Dealer. B260E01HP-GAT
SEAT BELT WARNING
LIGHT
The seat belt warning light blinks for
about 6 seconds when the ignition key
is turned from the "OFF" position to
"ON" or "START".
CAUTION:
When you move the electric power
steering back-end and forth-end
continuously in stop position, steer-
ing wheel plays heavily to operate
anti-overload system. It is normal
condition. It returns to be nomal
getting time.!
B260U01TB-EAT IMMOBILIZER
INDICATOR LIGHT
(Not all models)
This indicator light comes on for some
seconds after the ignition key is turned
to the "ON" position. At this time, you
can start the engine. The light goes out
after the engine is running. In case this
light goes out before you start the en-
gine, you must turn to the "LOCK"
position and restart the engine. In case
this light blinks for five seconds when
the ignition key is turned to "ON" posi-
tion, this indicates that the immobilizer
system is out of order. At this time,
consult to the Hyundai dealer.
nearest authorized Hyundai dealer and
have the system checked.
tbuk-1a.p65
3/23/04, 2:22 PM
42

FEATURES OF YOUR HYUNDAI 1- 45
B310B01TB-EAT
ODOMETER/TRIP ODOMETER
A TYPE
(WITH TRIP COMPUTER)
1. Odometer
The odometer records the total driving
distance in miles and is useful for keep-
ing a record for maintenance intervals.
NOTE:
Any alteration of the odometer may
void your warranty coverage. HTB008B
A Type
B Type 2. Trip odometer
o This mode indicates the drive dis-
tance travelled since the last drive
time reset.
o Pressing the reset switch built in left
side of speedmeter for more than 1
second, when the drive distance is
being displayed, clears the drive
distance to zero.
o Refer to the explanation of the trip computer (see page 1-45, Drive Dis-
tance).
B TYPE
(WITHOUT TRIP COMPUTER)
Function of digital odometer/trip
odometer
Pushing in the reset switch when the
ignition switch is turned "ON" will dis-
play the following sequence:
The tachometer registers the speed of
the engine in revolutions per minute
(R.P.M.).
SB215F1-E
TACHOMETER
A Type
!
CAUTION:
The maximum safe engine operating
speed is indicated by the red zone of
the tachometer scale. The engine
should not be operated beyond the
beginning of this zone or serious
engine damage may result. HTB005A
B Type
tbuk-1a.p65
3/23/04, 2:22 PM
45

FEATURES OF YOUR HYUNDAI 1- 49
HTB017-DHTB015-D
B340C03FC-EAT
LIGHTING SWITCH
The vehicle side lights and headlights
are operated by rotating the end of the
turn signal switch barrel. To operate the
side lights, rotating the switch to the
first detent with ignition switch at the
"OFF" position will cause the lights to
illuminate. To operate the headlights,
the turn signal switch barrel should be
rotated to the second detent. The head-
lights will only operate when the ignition
switch is at the "On" position. If the
ignition switch is turned to the "Off"
position, only the side lights will func-
tion.
NOTE:
The ignition must be in the "ON"
position to turn on the headlights. Side light auto cut
(Not all models)
If you do not turn the side lights "OFF"
after driving, the side light will automati-
cally shut "OFF" when the driver's door
is opened.
To turn them "ON" again you must
simply turn the ignition key to the "ON"
position.
SB220D1-E
HIGH AND LOW BEAM
To turn on the headlight high beams,
push the lever forward (away from you).
For low beams, pull the lever back
(toward you). The appropriate headlight
beam indicator light will come on at the
same time.
SB220E1-E
HEADLIGHT FLASH
The headlights may be flashed by pull-
ing the turn signal switch lever towards
the steering wheel. The headlights will
be extinguished when the switch is
released.
tbuk-1a.p65
3/23/04, 2:22 PM
49

1- 52 FEATURES OF YOUR HYUNDAI
SB250A1-E
HEATED REAR WINDOW
To operate the heated rear window de-
press the switch shown. The heated
rear window will automatically turn off
after 20 minutes or when the ignition is
turned off.
The system may be turned off manually
by depressing the switch again. HTB039CAUTION:
The inside of the rear windscreen
should never be cleaned with a hard
or sharp implement since damage to
the heating element may occur. The
glass should only be cleaned with a
soft cloth or chamois leather with the
use only of a mild detergent or pro-
prietary glass cleaner where neces-
sary. Only horizontal movement of
the cloth should be made when clean-
ing the glass and care should be
exercised to ensure that the heating
elements are not damaged by rings
or jewellery whilst the glass is being
cleaned.
NOTE:
The engine must be running for the
heated rear window to operate.
! B360B01FC-EAT
FRONT FOG LIGHT SWITCH
(Not all models)
HTB094
To turn on the front fog lights, push the
switch in the "ON" position. They will
come on when the headlight switch is in
the first or second position.
tbuk-1a.p65 3/23/04, 2:22 PM
52

1- 56 FEATURES OF YOUR HYUNDAI
!
B460B01GK-GAT
Opening the Sunroof System
The sunroof can be electrically opened
or closed with the ignition key in the
"ON" position. The sunroof is moved to
its fully open position by pushing the
"Open" switch, and to stop at the de-
sired position, push in any switches
(Open, Close, Up, Down). To close,
press and hold the "CLOSE" button.
Release the button when the sunroof
reaches the desired position. HFC2021
HFC2022
B460C01GK-GAT
Tilting the Sunroof System
The sunroof is moved to its fully tilt up
position by pushing the "UP" switch,
and to stop at the desired position,
push in any switches (Open, Close,
Up, Down).
To tilt down, press and hold the
"DOWN" button. Release the button
when the sunroof reaches the desired
position.
NOTE:
After washing the car or after there
is rain, be sure to wipe off any water
that is on the sunroof before oper-
ating it.
WARNING:
o Do not close a sunroof if anyone’s hands, arms or body are between
the sliding glass and the sunroof
sash, as this could result in in-
jury.
o Do not place your head or arms
out of the sunroof opening at any
time.
CAUTION:
o Do not open the sunroof in se- verely cold temperature or when
it is covered with ice or snow.
o Periodically remove any dirt that may have accumulated on the
guide rails.
!
tbuk-1a.p65 3/23/04, 2:22 PM
56

FEATURES OF YOUR HYUNDAI 1- 57
2. Insert the hexagonal head wrench
provided with the vehicle into the
socket. This wrench can be found in
the vehicle’s trunk or glove box.
3. Turn the wrench counterclockwise to open or clockwise to close the
sunroof. HGK033B460E01TB-GAT
Resetting the Sunroof System
If the battery has been recharged,
disconnected, if the sunroof is oper-
ated with the hexagonal head wrench
manually, or if the sunroof operation is
stopped by that ignition key is turned to
the "OFF" position while it is moving,
you may need to reset the sunroof.
To do this;
1. Turn the ignition switch "OFF".
2. With pressing "open" "up" button at
the same time, turn the ignition
switch "ON".
3. If the sunroof is set like this, the
sunroof is reset with tilting up/down
automatically once for all.
! CAUTION:
If the sunroof is not reset, it may not
be operated properly.
B460D01TB-AAT
Manual Operation of Sunroof
If the sunroof does not electrically op-
erate:
HGK032
1. Remove the cap located in the rear roof panel by using a coin or screw
driver.
tbuk-1a.p65 3/23/04, 2:22 PM
57

1- 58 FEATURES OF YOUR HYUNDAI
With Sunroof
B480A01E-EAT
INTERIOR LIGHT
Map Light
The two map lights are located at each
side of the interior light.
The lights may be operated by depress-
ing the switch to turn on the light and
pressing again to turn off the light. This
light produces a spot beam for conve-
nient use as a map light at night or as a
personal light for the driver or the pas-
senger.Without Sunroof
HTB050
HTB102-D
B491A01TB-GAT
SPECTACLE CASE
(Not all models)
The spectacle case is located on the
driver side of roof trim.
Pull the end of the cover to open the
spectacle case.
HTB303
With Sunroof
Without unroof
SB340B1-E
Interior Light
The interior courtesy light has a button
of three positions.
The three positions are:
oDR
In the "DR" position, the interior cour-
tesy light comes on when any door is
opened regardless of the ignition key
position. The light goes out when the
door is closed.
oON
In the "ON" position, the light stays on
at all times. o OFF
In the "OFF" position, the light stays off
at all times even though a door is open.
tbuk-1a.p65
3/23/04, 2:22 PM
58

1- 62 FEATURES OF YOUR HYUNDAI
The parking brake must always be set
when the vehicle is to be left unat-
tended. When the parking brake is ap-
plied, and the ignition key is at the "ON"
position, the parking brake warning light
will be illuminated. Before driving the
vehicle, the parking brake must be fully
released and the warning light extin-
guished.
o To set the parking brake, apply the
foot brake and pull the parking brake
lever up with the button depressed.
Release the button when the brake is
fully applied.
SB380A1-E
PARKING BRAKE
B550A01S-DAT
HIGH-MOUNTED REAR STOP
LIGHT
In addition to the lower-mounted rear
stoplights on either side of the car, the
high mounted rear stoplight in the cen-
tre of the rear window or inserted in the
rear spoiler also lights when the brakes
are applied.
HTB251
HTB255
o To release the parking brake, apply
the foot brake and pull up the parking
brake lever slightly. Depress the
button and lower the lever.
B750A01TB-DAT
BONNET RELEASE
HTB070-D
1. Pull the release knob to unlatch the bonnet.
HTB069
2. Push the safety catch lever sidewards and lift the bonnet.
tbuk-1a.p65 3/23/04, 2:22 PM
62

DRIVING YOUR HYUNDAI 2- 3
!
C020A01O-EAT BEFORE STARTING THE EN- GINE Before you start the engine, you should always:
1. Look around the vehicle to be sure
there are no flat tyres, puddles of oil or water or other indications of pos- sible trouble.
2. After entering the car, check to be
sure the parking brake is engaged.
3. Check that all windows, and lights are clean.
4. Check that the interior and exterior
mirrors are clean and in position.
5. Check your seat, seatback and
headrestraint to be sure they are intheir proper positions.
6. Close all the doors.
7. Fasten your seat belt and be sure
that all other occupants have fas- tened theirs.
8. Turn off all lights and accessories that are not needed.
9. When you turn the ignition switch to "ON" check that all appropriate warn-ing lights are operating and that youhave sufficient fuel. 10.Check the operation of warning
lights and all bulbs when key is inthe "ON" position.
WARNING: (DIESEL ENGINE)
To ensure that sufficient vacuum exists within the brake system dur-ing cold weather start-up condi-tions, it is necessary to run theengine at idle for several seconds after starting the engine. SC040A1-F COMBINATION IGNITION SWITCH AND STEERING LOCK To Start the Engine
o If your Hyundai is equipped with a
manual transaxle, place the shift lever in neutral and depress theclutch pedal fully.
o If your Hyundai has an automatic
transaxle, place the shift lever in "P" (park).
o To start the engine, insert the igni-
tion key and turn it to the "START" position. Release it as soon as theengine starts. Do not hold the key inthe "START" position for more that 15 seconds.
NOTE: For safety, the engine will not start if the shift lever is not in "P" or "N"Position (automatic transaxle).
tbuk-2.p65 3/23/04, 4:55 PM
3

2- 4 DRIVING YOUR HYUNDAI
!
"START" The engine is started in this position. It will crank until you release the key. NOTE: Do not hold the key in the "START" position for more than 15 seconds. "ON" When the key is at the "ON" position, the ignition and all accessories are available for use. If the engine is notrunning, the key should not be left atthis position since the battery will be-come discharged and damage to theignition system may also result. For information regarding engine starting, refer to "STARTING THE ENGINE". "ACC" When the ignition key is at the "ACC" position, the radio and other accesso-ries may be used. "LOCK" The ignition key may only be inserted or removed at this position.SC050A2-E KEY POSITIONS
C040A01E
LOCK
ACC
ON
START
WARNING:
The engine must never be turned off and the key removed from the ignition key cylinder whilst the ve- hicle is in motion since the steeringlock will operate and control of thevehicle will be lost. SB050B1-E STEERING WHEEL LOCK When the key is removed, the steering column lock will be activated and willengage when the steering wheel isturned to the appropriate position. It isnot necessary to turn the wheel until locked each time the key is removed since in the event of any unauthorizedattempt at removal, the lock will be-come effective as soon as the steeringwheel is turned. To unlock the steer-ing, insert the key and turn to the "ACC" position. If the steering is locked, it may be necessary to rock the steer-ing wheel slightly to facilitate turningthe key. Under no circumstancesshould the key be forced since break-age of the key will occur.
tbuk-2.p65
3/23/04, 4:55 PM
4