ignition HYUNDAI GX350 L 2005 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2005, Model line: GX350 L, Model: HYUNDAI GX350 L 2005Pages: 247, PDF Size: 7.48 MB
Page 9 of 247
1. Cruise Control Main Switch
2. Traction Control Switch
3. Panel Brightness Control Knob (Rheostat
Switch)
4. Multi-Function Light Switch
5. Horn and Driver's Airbag
6. Cruise Control Switch
7. Windshield Wiper/Washer Switch
8. Ignition Switch
9. Hazard Warning Switch
10. Digital Clock11. Audio System (If installed)
12. Passenger's Airbag
13. Hood Release Lever
14. Parking Brake Release Lever/Parking Brake (Foot
type)
15. Steering Wheel Tilt Lever
16. Heater/Air Conditioning Control Panel
17. Shift Lever
18. Ashtray
19. Accessory Box
20. Glove Box
CAUTION:
When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor
on the instrument panel surface. If there is any leakage from the air freshener onto these areas (Instrument cluster,
instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these
areas, wash them with water immediately.
!
xgflhma-0.p656/16/04, 3:05 PM 9
ProCarManuals.com
Page 15 of 247
1
FEATURES OF YOUR HYUNDAI
3
KEY
BREAKING IN YOUR NEW HYUNDAI
B010E01A-AATGasolines for Cleaner AirTo help contribute to cleaner air, Hyundai rec-
ommends that you use gasolines treated with
detergent additives, which help prevent deposit
formation in the engine. These gasolines will
help the engine run cleaner and enhance per-
formance of the Emission Control System.B010F01A-AATOperation in Foreign CountriesIf you are going to drive your Hyundai in another
country, be sure to:
o Observe all regulations regarding registra-
tion and insurance.
o Determine that acceptable fuel is available.
B020A01S-AATDuring the First 1,200 Miles (2,000 Km)No formal "break-in" procedure is required with
your new Hyundai. However, you can contrib-
ute to the economical operation and durability of
your Hyundai by observing the following recom-
mendations during the first 1,200 miles (2,000
km).
o Don't drive faster than 55 MPH (88 km/h).
o While driving, keep your engine speed (rpm,
or revolutions per minute) between 2,000
rpm and 4,000 rpm.
o Use moderate acceleration. Don't start
quickly or depress the accelerator pedal
fully.
o For the first 200 miles (300 km), try to avoid
hard stops.
o Don't lug the engine (in other words, don't
drive so slowly in too high a gear that the
engine "bucks"-shift to a lower gear).
o Whether going fast or slow, vary your speed
from time to time.
o Don't let the engine idle longer than 3 minutes
at one time.
o Don't tow a trailer during the first 1,200 miles
(2,000 km) of operation.
B030A01Y-AATKEYSFor greater convenience, your Hyundai has
two master keys and a sub key. The master
keys will open all locks on your vehicle. The sub
key will only function in the ignition and the door
locks.
Leaving your sub key with a parking attendant
will ensure that your vehicle's trunk, trunk lid
release, glovebox compartment and rear trunk
access may not be unlocked in your absence.NOTE:Before leaving your sub key with a parking
attendant, make sure that the lock levers of
the rear seat back lock and the trunk lid lock
are switched to the "LOCK" position.
HXG116
Master key
Sub key
xgflhma-1.p656/16/04, 3:02 PM 3
ProCarManuals.com
Page 16 of 247
1FEATURES OF YOUR HYUNDAI4
DOOR
ILLUMINATED IGNITION SWITCH
!
B030C01Y-AATB040A01Y-AAT
DOOR LOCKS
Whenever a door is opened, the ignition switch
will be illuminated for your convenience, pro-
vided the ignition switch is not in the "ON"
position.
The light will go off approximately 10 seconds
after closing the door or when the ignition switch
is turned on.
B030C01L
WARNING:
o Unlocked doors can be dangerous. Be-
fore you drive away (especially if there
are children in the car), be sure that all the
doors are securely closed and locked so
that the doors cannot be opened from
the inside. This helps ensure that the
doors will not be opened accidentally.
Also, when combined with the proper
use of seat belts, locking the doors helps
keep occupants from being ejected from
the car in case of an accident.
o Before opening the door, always look for
and avoid oncoming traffic.
o In case of accident, the door is unlocked
automatically.
B030B01A-AATRecord Your Key NumberA code number is stamped on the number plate
that came with the keys to your Hyundai. This
key number plate should not be left with the keys
but kept in a safe place, not in the vehicle. The
key number should also be recorded in a place
where it can be found in an emergency.
If you need additional keys, or if you should lose
your keys, your authorized Hyundai dealer can
make new keys if you can supply the key
number.
B030B01L
xgflhma-1.p656/16/04, 3:02 PM 4
ProCarManuals.com
Page 17 of 247
1
FEATURES OF YOUR HYUNDAI
5
B040C03L
UNLOCK
LOCK
HXG018 B040B01A-AAT
Locking and unlocking front doors with a
key
B040C02Y-AATLocking From the OutsideThe doors can be locked without a key. To lock
the doors, first push the inside lock switch to the
"LOCK" position so that the red mark on the
switch is not visible, then close the door.
The door will not lock if the key is left in the ignition
switch when the front doors close. This is
normal.NOTE:o When locking the door this way, be care-
ful not to lock the door with the ignition
key left in the vehicle.
o To prevent against theft, always remove
the ignition key, close all windows, and
lock all doors and the trunk lid when
leaving your vehicle unattended.
B040D02S-AATLocking From the Insideo To lock the doors from the inside, simply
close the door and push the lock switch to the
"LOCK" position. When this is done, neither
the outside nor the passenger's inside door
handle can be used.
o The driver's door can be opened by pulling
the inside door handle even if the lock switch
is depressed.NOTE:When the door is locked, the red mark on the
switch is not visible. o The door can be locked or unlocked with a
key.
o Lock the door by turning the key toward the
front of the vehicle and unlock it by turning the
key toward the rear.
HXGS226LOCK UNLOCK
xgflhma-1.p656/16/04, 3:02 PM 5
ProCarManuals.com
Page 19 of 247
1
FEATURES OF YOUR HYUNDAI
7
THEFT-ALARM SYSTEMB070A01S-AAT(If Installed)This system is designed to provide protection
from unauthorized entry into the car. This sys-
tem is operated in three stages : the first is the
"Armed" stage, the second is the "Alarm" stage,
and the third is the "Disarmed" stage. If trig-
gered, the system provides an audible alarm.B070B03Y-AATArmed StagePark the car and stop the engine. Arm the
system as described below.
1) Remove the ignition key from the ignition
switch.
2) Make sure that the engine hood and trunk lid
are locked.
3) Lock the doors using the transmitter of the
keyless entry system.
After completion of the steps above, the turn
signal light will blink once to indicate that the
system is armed.NOTE:1) If any door, trunk lid or engine hood
remains open, the system will not be
armed.
2) If this happens, rearm the system as
described above.
CAUTION:
Do not arm the system until all passengers
have left the car. If the system is armed while
a passenger(s) remains in the car, the alarm
may be activated when the remaining
passenger(s) leaves the car.B070C03L-GATAlarm StageThe alarm will be activated if any of the following
occurs while the car is parked and the system
is armed.
HXGS123
!
CAUTION:
Avoid trying to start the engine while the
system is armed.
!
1) A front or rear door is opened without using
the transmitter.
2) The trunk lid is opened without using the
transmitter.
3) The engine hood is opened.
The turn signal lights will blink continuously and
the siren will sound for 27 seconds. (EC only/
Except E.C: This happens 3 times). To turn off
the system, unlock the door or trunk lid with the
transmitter.
xgflhma-1.p656/16/04, 3:02 PM 7
ProCarManuals.com
Page 20 of 247
1FEATURES OF YOUR HYUNDAI8
B070E02HP-GATReplacing the batteryWhen the transmitter's battery begins to get
weak, it may take several pushes on the button
to lock or unlock the doors, and the LED will not
light. Replace the battery as soon as possible.
Battery type : CR2032
Replacement instructions:
1. Carefully separate the case with a blade
screwdriver as shown in the illustration.
HEF-192A
Screwdriver
CAUTION:
Only the transmitter can disarm the armed
stage. If the transmitter does not disarm the
system, it is necessary to take the following
steps;
1. Unlock the door with the key, which will
cause the alarm to be activated.
2. Insert the key in the ignition key cylinder
and turn the ignition key to "ON" posi-
tion.
3. Wait for 30 seconds.
After completing the steps above, the sys-
tem will be disarmed.
!
HXG117
UNLOCK
LOCK
TRUNK
B070D04L-AATDisarmed StageThe system will be disarmed when the following
step is taken:
The driver's or passenger's door is unlocked by
depressing the " " button on the transmitter.
After completion of the steps above, the turn
signal lights will blink twice to indicate that the
system is disarmed.
xgflhma-1.p656/16/04, 3:02 PM 8
ProCarManuals.com
Page 21 of 247
1
FEATURES OF YOUR HYUNDAI
9
2. Remove the old battery from the case and
note the polarity. Make sure the polarity of
the new battery is the same(+side facing
down), then insert it in the transmitter.
HEF-193
Battery
POWER WINDOWSB060A03Y-AATThe power windows operate when the ignition
key is in the "ON" position. The main switches
are located on the driver's armrest and control
the front and rear windows on both sides of the
vehicle. The windows may be opened by de-
pressing the appropriate window switch and
closed by pulling up the switch. To open the
window on the driver's side, press the switch(1)
halfway down. The window moves as long as
the switch is operated. To fully open the driver's
window automatically, press the switch fully
down. In automatic operation, the window will
fully open even if you let go of the switch. To stop
at the desired opening, pull up and release the
switch.In order to prevent operation of the passanger
front and rear windows, a window lock switch(2)
is provided on the armrest of the driver's door.
To disable the power windows, press the win-
dow lock switch. To return to normal operation,
press the window lock switch a second time.
NOTE:The power windows can be operated for 30
seconds after the ignition key is turned to
the "ACC" or "LOCK" positions, or removed
from the ignition switch.
If the front doors are opened during this 30
second period, the power windows can no
longer be operated without the ignition key
turned to the "ON" position.
HXG129-1
OpenClose
HXG025-1
(1)
(2)
xgflhma-1.p656/16/04, 3:02 PM 9
ProCarManuals.com
Page 22 of 247
1FEATURES OF YOUR HYUNDAI10
SEATS!
B080A01A-AATADJUSTABLE FRONT SEATS
WARNING:Never attempt to adjust the seat while the
vehicle is moving. This could result in loss
of control or an accident which may cause
death, serious injury, or property damage.
B080B01L-AATAdjusting Seat Forward and RearwardTo move the seat toward the front or rear, pull
the lock release lever upward. This will release
the seat on its track so you can move it forward
or rearward to the desired position. When you
find the position you want, release the lever and
slide the seat forward or rearward on its track
until it locks into the desired position and cannot
be moved further.
HXG179
!
WARNING:
To ensure the seat is locked securely, at-
tempt to move the seat forward or rearward
without using the control knob.
!
WARNING:
(1) Be careful that someone's head, hands
and body are not trapped by a closing
window.
(2) Never try to operate the main switch on
the driver's door and the individual door
window switch in opposing directions
at the same time. If this is done, the
window will stop and cannot be opened
or closed.
(3) Do not leave children alone in the car.
Always remove the ignition key for their
safety.
HXG029
Close
Open
xgflhma-1.p656/16/04, 3:02 PM 10
ProCarManuals.com
Page 26 of 247
1FEATURES OF YOUR HYUNDAI14
B090E05L-AATI.M.S (Integrated Memory System)
(If Installed)The Integrated Memory System controls are
located on the driver's door. After adjusting the
position of the driver's seat and outside rear-
view mirrors, use the I.M.S to memorize them.
Two different driving position profiles can be
entered in the I.M.S. If you turn the ignition key
to the "ON" position, the memorized position is
adjusted automatically.
HXG212
!
B090D01Y-AATAdjusting Seatback Angle
HXG181
Rotate the upper portion of the control knob
forward or backward to adjust the seatback to
the desired position. Release the control knob
and the seatback will remain in that position.
WARNING:
To minimize the risk of personal injury in
the event of a collision or a sudden stop,
both the driver's and passenger's seatbacks
should remain in an upright position while
the car is in motion. The protection pro-
vided by the seat belts and airbags may be
reduced significantly when the seatbacks
are reclined. There is a greater risk that the
seat occupants will slide under the seatbelt
resulting in serious injury if a crash occurs
when the seatbacks are reclined. The seat
belt cannot provide full protection to an
occupant if the seatback is reclined.
xgflhma-1.p656/16/04, 3:02 PM 14
ProCarManuals.com
Page 27 of 247
1
FEATURES OF YOUR HYUNDAI
15
Reverse Parking Aid FunctionWhen the "AUTO" button is "ON" and the
vehicle is moving backward, the outside rear-
view mirror(s) will move downward to aid re-
verse parking safely. According to the position
of the outside rearview mirror switch knob, the
outside rearview mirror(s) will operate as fol-
lows.
L: When the remote control outside rearview
mirror switch knob is selected to the "L"
position, both of the outside rearview mir-
rors will move downward.
R: When the remote control outside rearview
mirror switch knob is selected to the "R"
position, only the passenger's outside rear-
view mirror will move downward.
Neutral: When the remote control outside rear-
view mirror switch knob is placed in
the middle position, the outside rear-
view mirrors will not operate while the
vehicle is moving backward.NOTE:When the ignition key is in the "LOCK"
position, the selector lever is moved to any
position except "R" position, or the remote
control outside rearview mirror switch knob
is placed in the middle position, the outside
rearview mirrors will automatically revert to
original position.
!
CAUTION:
In the following conditions, the I.M.S will
not operate.
1. When the "1" or "2" button is not pushed
within five seconds.
2. When the seat is being adjusted.
3. When the "STOP" button is pushed.
4. While the vehicle is moving.To activate the memorized positionWhen you push button "1" or "2", the driving
position will be automatically adjusted to the
position recorded for that button.To memorize driving position1. Turn the ignition key "ON".
2. Adjust the driver's seat and outside rearview
mirrors to the desired position.
3. Push the "M" button on the I.M.S until the
signal beeps.
4. Within five seconds, push button "1" or "2"
until the signal beeps twice. The beep sounds
mean that the positions are memorized in the
I.M.S.
"AUTO" button functionWhen the "AUTO" button is "ON", the system
will move the driver's seat forward or rearward
so you can comfortably enter and exit the
vehicle.
o It will move driver's seat rearward when the
ignition key is pulled out.
o It will move driver's seat forward when the
ignition key is inserted.Note:In order for the "AUTO" functions to work,
the parking brake must be applied.
CAUTION:
In the following conditions, the "AUTO"
mode will not operate.
1. When AUTO button is in "OFF".
2. When the seat is being adjusted.
3. When the shift lever is positioned in
other than "P" position.
!
xgflhma-1.p656/16/04, 3:02 PM 15
ProCarManuals.com