warning HYUNDAI I20 2017 User Guide

9
"&t%'s%st&'!"'%!'&&

To reinstall the headrest :
1. Put the headrest poles (2) into theholes while pressing the release
button (1).
2. Recline the seatback (4) with the recline lever (3).
3. Adjust the headrest to the appro priate height.
Seatback pocket (if equipped)Rear seats
Headrest
The rear seats are equipped with
headrests in all the seating positions
for the occupant's safety and com
fort.
The headrest not only provides com
fort for passengers, but also helps to
protect the head and neck in the
event of a collision.
OIB034007
OIB034008
Seatback pockets
Do not put heavy or sharp objects
in the seatback pockets. In an
accident they could come loose
from the pocket and injure vehicle
occupants.
WARNING
Always make sure the headrest
locks into position after reinstalling
and adjusting it properly.
WARNING
OIB034038

To prevent damage, NEVER hit or
pull on the headrests.
Adjusting the height up and down
(if equipped)
To raise the headrest, pull it up (1).
To lower the headrest, push and hold
the release button (2) on the head
rest support and lower the headrest
(3).
NOTICE
1
"&t%'s%st&'!"'%!'&&
(Continued)
•NEVER adjust the headrest
position of the driver’s seat when
the vehicle is in motion.
•Adjust the headrest as close to
the passenger’s head as possi
ble. Do not use a seat cushion
that holds the body away from
the seatback.
•Make sure the headrest locks
into position after adjusting it.
OIB034009
To reduce the risk of serious injury
or death in an accident, take the
following precautions when
adjusting your headrests:
•Always properly adjust the head
rests for all passengers BEFORE
starting the vehicle.
•NEVER let anyone ride in a seat
with the headrests removed.
•
Adjust the headrests so the middle
of the headrests is at the same
height as the height of the top of
the eyes.(Continued)
WARNING
OLF034072N

11
"&t%'s%st&'!"'%!'&&

Removal (if equipped)
To remove the headrest, raise it as far
as it can go then press the release
button (1) while pulling upward (2).To reinstall the headrest, put the
headrest poles (3) into the holes
while pressing the release button (1).
Then adjust it to the appropriate
height.
Folding the rear seat
The rear seatbacks (or cushions)
may be folded to facilitate carrying
long items or to increase the luggage
capacity of the vehicle. 1. Set the front seatback to the
upright position and if necessary,
slide the front seat forward.
2. Insert the rear lap\fshoulder belt plate into the holder on the side
trim. It will prevent the lap\fshoulder
belt from interfering with the seat
back when folding.
•Never allow passengers to sit on
top of the folded down seatback
while the vehicle is moving as
this is not a proper seating posi
tion and no seat belts are avail
able for use. This could result in
serious injury or death in case of
an accident or sudden stop.
•Objects carried on the folded
down seatback should not
extend higher than the top of the
front seats. This could allow
cargo to slide forward and cause
in

jury or damage during sudden
stops.
WARNING
OIB034010
Make sure the headrest locks in
position after adjusting it to prop
erly protect the occupants.
WARNING
OIB037011

12
"&t%'s%st&'!"'%!'&&
3. Pull up both sides of the seatback lever and fold the seatback toward
the front of the vehicle. To use the rear seat, lift and push up
the seatback backward. Push the
seatback firmly until it clicks into
place. Make sure the seatback is
locked in place.
When returning the rear seatbacks to
the upright position, remember to
return the rear shoulder belts to their
proper position.
Information
If you are not able to pull out the seat
belt from the retractor, firmly pull the
belt out and release it. Then you will
be able to pull the belt out smoothly.
iOIB037012
OIB034013
When you return the rear seat
back to its upright position after
being folded down:
Be careful not to damage the seat
belt webbing or buckle. Do not
allow the seat belt webbing or
buckle to get caught or pinched in
the rear seat. Ensure that the
seatback is completely locked into
its upright position by pushing on
the top of the seatback.
Otherwise, in an accident or sud
den stop, the seat could fold down
and allow cargo to enter the pas
sen

ger compartment, which could
result in serious injury or death.
WARNING

1
"&t%'s%st&'!"'%!'&&

• When returning the rear seatbacksto the upright position, remember
to return the rear shoulder belts to
their proper position.
• Routing the seat belt webbing through the rear seat belt guides
will help keep the seat belts from
being trapped behind or under the
seats.
Armrest (if equipped)
The armrest is located in the center
of the rear seat. Pull the armrest
down from the seatback to use it.
NOTICE
Cargo loading
Make sure the engine is off, the
Continuously Variable Transaxle
is in P (Park) or the Manual
Transaxle is in R (Reverse) or 1st,
and the parking brake is securely
applied whenever loading or
unloading cargo. Failure to take
these steps may allow the vehicle
to move if the shift lever is inad
vertently moved to another posi
tion.
WARNING
Cargo
Cargo should always be secured
to prevent it from being thrown
about the vehicle in a collision and
causing injury to the vehicle occu
pants. Do not place objects in the
rear seats, since they cannot be
properly secured and may hit the
front seat occupants in a collision.
WARNING OIB037043

1
"&t%'s%st&'!"'%!'&&

$#%$!%

•For maximum restraint system
protection, the seat belts must
always be used whenever the
car is moving.
•Seat belts are most effective
when seatbacks are in the
upright position.
•Children age 12 and under must
always be properly restrained in
the rear seat. Never allow chil
dren to ride in the front passen
ger seat. If a child over 12 must
be seated in the front seat,
he\fshe must be properly belted
and the seat should be moved
a

s far back as possible.
(Continued)
WARNING (Continued)
•Never wear the shoulder belt
under your arm or behind your
back. An improperly positioned
shoulder belt can cause serious
injuries in a crash. The shoulder
belt should be positioned mid
way over your shoulder across
your collarbone.
•Never wear a seat belt over
fragile objects. If there is a sud
den stop or impact, the seat belt
can damage it.
•Avoid wearing twisted seat
belts. A twisted belt can't do its
job as

well. In a collision, it could
even cut into you. Be sure the
belt webbing is straight and not
twisted.
•Be careful not to damage the
belt webbing or hardware. If the
belt webbing or hardware is
damaged, replace it.
Seat belts are designed to bear
upon the bony structure of the
body, and should be worn low
across the front of the pelvis or the
pelvis, chest and shoulders, as
applicable; wearing the lap section
of the belt across the abdominal
area must be avoided.
Seat belts should be adjusted as
firmly as possible, consistent with
comfort, to provide the protection for
which they have been designed.
A slack belt will greatly reduce the
protection afforded to the wearer.
Care sh

ould be taken to avoid con
tamination of the webbing with pol
ishes, oils and chemicals, and par
ticularly battery acid. Cleaning may
safely be carried out using mild
soap and water. The belt should be
replaced if webbing becomes
frayed, contaminated or damaged.
(Continued)
WARNING

1
"&t%'s%st&'!"'%!'&&

Seat belt warning (if equipped)
As a reminder to the driver (or front
passemgers)*, the driver’s (or front
passemger’s)* seat belt warning
lights will illuminate for approximate
ly 6 seconds each time you turn the
ignition switch ON regardless of belt
fastening.
If the driver’s (or front passemger’s)*
seat belt is not fastened when the
ignition switch is turned ON or if it is
disconnected after the ignition switch
is turned ON, the seat belt warning
light will illuminate until the belt is
fastened.
(Continued)
It is essential to replace the entire
assembly after it has been worn in
a severe impact even if damage to
the assembly is not obvious. Belts
should not be worn with straps
twisted. Each belt assembly must
only be used by one occupant; it is
dangerous to put a belt around a
child being carried on the occu
pant's lap.
•No modifications or additions
should be made by the user
which will either prevent the seat
belt adjusting devices from oper
ating to remove slack, or prevent
the seat belt assembly from being
adjusted to remove slack.(Continued)
WARNING
(Continued)
•When you fasten the seat belt, be
careful not to latch the seat belt in
buckles of other seat. It's very dan
gerous and you may not be pro
tected by the seat belt properly.
•Do not unfasten the seat belt and
do not fasten and unfasten the
seat belt repeatedly while driving.
This could result in loss of control,
and an accident causing death,
serious injury, or property dam
age.
•When fastening the seat belt,
make sure that the seat belt does
not pass
over objects that are
hard or can break easily.
•Make sure there is nothing in the
buckle. The seat belt may not be
fastened securely.
1GQA2083

1
"&t%'s%st&'!"'%!'&&
If you continue not to fasten the seat
belt and you drive over 9 km\fh, the
illuminated warning light will start to
blink until you drive under 6 km\fh.
If you continue not to fasten the seat
belt and you drive over 20 km\fh (12
mph) the seat belt warning chime will
sound for approximately 100 sec
onds and the corresponding warning
light will blink.
*: if equipped
Lap\fshoulder belt
To fasten your seat belt:
To fasten your seat belt, pull it out of
the retractor and insert the metal tab
(1) into the buckle (2). There will be
an audible "click" when the tab locks
into the buckle. You should place the lap belt (1) por
tion across your hips and the shoul
der belt (2) por tion across your
chest.
The seat belt automatically adjusts to
the proper length only after the lap
belt portion is adjusted manually so
that it fits snugly around your hips. If
you lean forward in a slow, easy
motion, the belt will extend and let
you move around. If there is a sud
den stop or impact, however, the belt
will lock into position. It will also lock
if you try to lean forward too quickly.
ODH033055
ODH033053

18
"&t%'s%st&'!"'%!'&&
To release the seat belt:
The seat belt is released by pressing
the release button (1) in the locking
buckle. When it is released, the belt
should automatically draw back into
the retractor.
If this does not happen, check the
belt to be sure it is not twisted, then
try again.
Lap belt (if equipped)
To fasten your seat belt:
To fasten a 2point static type belt,
insert the metal tab into the locking
buckle. There will be an audible
"click" when the tab locks into the
buckle. Check to make sure the belt
is properly locked and that the belt is
not twisted.
OLMB033088
OLMB033089
OLMB033025
You should place the lap belt por
tion as low as possible and snugly
across your hips, not on your waist.
If the lap belt is located too high on
your waist, it may increase the
chance of injury in the event of a
collision. Both arms should not be
under or over the belt. Rather, one
should be over and the other
under, as shown in the illustration.
Never wear the seat belt under the
arm nearest the door.
WARNING

19
"&t%'s%st&'!"'%!'&&

With a 2point static type seat belt, the
length must be adjusted manually so
it fits snugly around your body. Fasten
the belt and pull on the loose end to
tighten. The belt should be placed as
low as possible on your hips, not on
your waist. If the belt is too high, it
could increase the possibility of your
being injured in an accident. When using the rear center seat belt,
the buckle with the “CENTER” mark
must be used.To release the seat belt:
When you want to release the seat
belt, press the button (1) in the lock
ing buckle.
OIB034016
The center lap belt latching mech
anism is different from those for
the rear seat shoulder belts. When
fastening the rear seat shoulder
belts or the center lap belt, make
sure they are inserted into the cor
rect buckles to obtain maximum
protection from the seat belt sys
tem and assure proper operation.
WARNING
OLMB03309OLMB033090
Too high
ShortenCorrect