clock HYUNDAI I20 2021 Owner's Manual

9-16
Emergency situations
OBC3080007OBC3080007
7. Place the jack at the designated
jacking position under the frame
closest to the tire you are changing.
The jacking positions are plates
welded to the frame with two tabs
and a raised dot. Never jack any other
position or part of the vehicle.
OAI3079010OAI3079010
8. Insert the jack handle into the jack and
turn it clockwise, raising the vehicle
until the tire clears the ground. Make
sure the vehicle is stable on the jack.
9. Loosen the lug nuts with the wheel
lug nut wrench and remove them with
your fingers. Remove the wheel from
the studs and lay it flat on the ground
out of the way. Before removing the
wheel lug nuts, make sure the vehicle
is stable on the jack.10. Install the spare tire onto the studs of
the hub.
11. Tighten the lug nuts with your fingers
onto the studs with the smaller end of
the lug nuts closest to the wheel.
12. Lower the vehicle to the ground
by turning the jack handle
counterclockwise.
OBC3080009OBC3080009
13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug nut
until they are tight. After changing
tires, we recommend that an
authorized HYUNDAI dealer tighten
the lug nuts to their proper torque as
soon as possible. The wheel lug nut
should be tightened to 11~13 kgf.m
(79~94 lbf.ft).

9-22
Emergency situations
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
NOTICE
Failure to place the shift lever in N
(Neutral) when being towed with the
front wheels on the ground can cause
internal damage to the transmission.
Removable towing hook
OBC3080018OBC3080018
„„5 Door5 Door
1. Open the tailgate/trunk, and remove
the towing hook from the tool case.
2. Remove the hole cover pressing the
lower part of the cover on the front
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

10-33
10
OBI3090009OBI3090009
„„Petrol Engine (1.0 T-GDi)Petrol Engine (1.0 T-GDi)
OBC3090006OBC3090006
„„Petrol Engine (Smartstream G1.2)Petrol Engine (Smartstream G1.2)
WARNING
Removing radiator cap
• Never attempt to remove the radiator
cap while the engine is operating or
hot. Doing so might lead to cooling
system and engine damage and could
result in serious personal injury from
escaping hot coolant or steam.• Turn the engine off and wait until it
cools down. Use extreme care when
removing the radiator cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back while the pressure
is released from the cooling system.
When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove
it.
• Even if the engine is not operating,
do not remove the radiator cap
or the drain plug while the engine
and radiator are hot. Hot coolant
and steam may still blow out under
pressure, causing serious injury.
WARNING
The electric motor (cooling
fan) is controlled by engine
coolant temperature,
refrigerant pressure and
vehicle speed. It may
sometimes operate even when the
engine is not running. Use extreme
caution when working near the blades
of the cooling fan so that you are not
injured by a rotating fan blades. As the
engine coolant temperature decreases,
the electric motor will automatically
shut off. This is a normal condition.

10-79
10
Headlight (Low/High) & Position
Light
1. Turn the front wheel at inwards.
OAC3089042TUOAC3089042TU
OAC3089043TUOAC3089043TU
OBC3090055OBC3090055
2. Remove retainers available on under
cover bottom area in the respective
side of headlight for bulb A/S.
3. Remove Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blot (C1) & retainer (C2).
OBC3090038OBC3090038
4. Pushing the Wheel guard aside & pull
front bumper near fender to unlock
front bumper with bumper bracket
near to headlight.
5. Remove the headlight bulb cover by
turning it counter-clockwise from bulb
assembly.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.

10-80
Maintenance
OBC3090057OBC3090057
Turn signal light
1. Open the hood.
2. Remove the turn signal light by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
Day running light (if equipped)
If not LED lamp does not operate,
we recommend that the system be
inspected by an authorized HYUNDAI
dealer. The LED lamps cannot be
replace as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
„„Front Fog lightFront Fog light
OBI3090025OBI3090025
Fog light (if equipped)
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.

10-82
Maintenance
OBC3090038OBC3090038
4. Pushing the Wheel guard aside & pull
front bumper near fender to unlock
front bumper with bumper bracket
near to headlight.
5. Remove the headlight bulb cover by
turning it counter-clockwise from bulb
assembly.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.
„„Front Fog lightFront Fog light
OBI3090025OBI3090025
Fog light (if equipped)
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.

10-83
10
Side repeater light replacement
OAC3089047TUOAC3089047TU
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.
Rear combination light bulb
replacement
Type A
OBI3090027OBI3090027
(1) Turn signal light
(2) Tail/Stop light
(3) Tail light
(4) Back-up light

10-84
Maintenance
OIB074037OIB074037
OIB074038AOIB074038A
1. Open the tailgate
2. Remove Lamp flange with given 2
provisions.
3. Loosen the light assembly retaining
screws with a cross-tip screwdriver.
4. Remove the rear combination light
assembly from the body of the
vehicle.
OBI3090041LOBI3090041L
[1] : Turn signal light, [2] : Tail/Stop light,
[3] : Tail light, [4] : Back-up light
Turn signal light, Tail/stop light
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.

10-85
10
Tail light & Back-up light
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the bulbs by rotating them in
counter clock wise direction.
4. Replace with new bulbs into the
sockets and then fix it in their
positions respectively.
Type B
OBI3090028OBI3090028
(1) Turn signal light
(2) Tail light
(3) Tail light
(4) Back-up light
(5) Stop light
OIB074037OIB074037
OIB074038AOIB074038A
1. Open the tailgate
2. Remove Lamp flange with given 2
provisions.
3. Loosen the light assembly retaining
screws with a cross-tip screwdriver.
4. Remove the rear combination light
assembly from the body of the
vehicle.

10-86
Maintenance
OBI3090042LOBI3090042L
[1] : Turn signal light, [2] : Back-up light
Turn signal light
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
Back-up light
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the bulb by rotating them in
counter clock wise direction.
4. Replace with new bulb into the Socket
and then fix it in its position.
Tail light, Stop light
If not LED lamp does not operate,
we recommend that the system be
inspected by an authorized HYUNDAI
dealer. The LED lamps cannot be
replace as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.