warning HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 181 of 649
5-40
Convenient features
OBC3N050015
3. Pull the fuel filler door out (1) to fully
open.
4. To remove the fuel tank cap (2), turn
it counterclockwise. You may hear a
hissing noise as the pressure inside
the tank equalizes.
5. Place the cap on the fuel filler door
(3).
i Information
, I W K H I X H O I L O O H U G R R U G R H V Q R W R S H Q
because ice has formed around it, tap
lightly or push on the door to break the
L F H D Q G U H O H D V H W K H G R R U ' R Q R W S U \ R Q W K H
G R R U , I Q H F H V V D U \ V S U D \ D U R X Q G W K H G R R U
with an approved de-icer fluid (do not use
U D G L D W R U D Q W L I U H H ] H R U P R Y H W K H Y H K L F O H
to a warm place and allow the ice to melt.
Closing the fuel filler door
1. To install the fuel tank cap, turn it
clockwise until it “Clicks”.
2. Close the fuel filler door until it is
latched securely.
WARNING
3 H W U R O L V K L J K O \ I O D P P D E O H D Q G
H [ S O R V L Y H ) D L O X U H W R I R O O R Z W K H V H
guidelines may result in SERIOUS
INJURY or DEATH:
[ Read and follow all warnings posted
at the gas station.
[ Before refuelling, note the location
R I W K H ( P H U J H Q F \ 3 H W U R O 6 K X W 2 I I L I
available, at the gas station.
[ Before touching the fuel nozzle, you
should eliminate the potential build-
up of static electricity by touching
a metal part of the vehicle, a safe
distance away from the fuel filler
neck, nozzle, or other gas source,
with your bare hand.
[ Do not use mobile phones whilst
refuelling. Electric current and/or
electronic interference from mobile
phones can potentially ignite fuel
vapours and cause a fire.
Page 184 of 649
5-43
05
OAE046469L
Position light position ()
The position light, license plate light and
instrument panel light are turned ON.
OAE046467L
+ H D G O L J K W S R V L W L R Q )
The headlight, position light, license
plate light and instrument panel light are
turned ON.
i Information
7 K H L J Q L W L R Q V Z L W F K P X V W E H L Q W K H 2 1
position to turn on the headlight.
High beam operation
OAE046453L
To turn on the high beam headlight,
push the lever away from you.
The high beam indicator will light when
the headlight high beams are switched
on.
To turn off the high beam headlight, pull
the lever towards you. The low beams
will turn on.
WARNING
Do not use high beam when there are
other vehicles approaching you. Using
high beam could obstruct the other
driver’s vision.
Page 189 of 649
5-48
Convenient features
WARNING
If the function does not work properly,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. Do not attempt to inspect or
replace the wiring yourself.
Low Beam Assist-Static light
Whilst driving a corner, for greater
visibility and safety, either the left or
right side Low Beam Assist-Static light
will turn on automatically. The Low
Beam Assist-Static light will turn on
when one of the following conditions
occurs.
[ Vehicle speed is less than 6 mph (10
km/h) and steering wheel angle is
turned approximately 80 degrees with
the low beam on.
[ Vehicle speed is between 6 mph
(10 km/h) to 56 mph (90 km/h)
and steering wheel angle is turned
approximately 35 degrees with the low
beam on.
[ When the vehicle is in reverse with
one of the conditions above satisfied,
the light opposite to the direction the
steering wheel is turned will turn on.
Page 191 of 649
5-50
Convenient features
- If the light switch is pushed away
when High Beam Assist is operating,
High Beam Assist will turn off.
- If the light switch is pulled towards
you when the high beam is off, the
high beam will turn on. When you let
go of the light switch, the lever will
move to the middle and the high beam
will turn off.
- If the light switch is pulled towards
you when the high beam is on by High
Beam Assist, and High Beam Assist
will turn off.
- If the light switch is placed to the
headlight position (
), High Beam
Assist will turn off and the low beam
will be on continuously.
When High Beam Assist is operating, the
high beam switches to low beam in the
following conditions.
- When the headlight of an on-coming
vehicle is detected.
- When the tail light of a vehicle in front
is detected.
- When the headlight or tail light of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light is
bright enough that high beams are not
required.
- When streetlights or other lights are
detected.
- When the light switch is not in the
AUTO position.
- When High Beam Assist is off.
- When the vehicle speed is below 19
mph (30 km/h).
System malfunction and
limitations
System malfunction
OTM050218L
When High Beam Assist is not working
properly, the warning message will come
on for a few seconds. After the message
disappears, the master warning light
(
) will illuminate.
We recommend that you take your
vehicle to a HYUNDAI authorised
repairer and have the system checked.
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an
on-coming vehicle or a vehicle in
front is dim. Such examples may
include:
[ When the headlights of an oncoming
vehicle or the tail lights of a vehicle
in front is covered with dust, snow,
or water
[ When the headlights on an
R Q F R P L Q J Y H K L F O H D U H 2 ) ) E X W W K H
fog lights are ON)
Page 192 of 649
5-51
05
2. When the front view camera is
adversely affected by an external
condition. Such examples may
include:
[ When the vehicle’s headlights have
been damaged or not repaired
properly
[ When the vehicle headlights are not
aimed properly
[ When the vehicle is driven on a
narrow curved road or rough road
[ When the vehicle is driven on an
uphill road or downhill road
[ When only part of the vehicle in front
is visible on a crossroad or curved
road
[ When there is a traffic light,
reflecting sign, flashing sign or mirror
[ When the road conditions are bad
such as being wet or covered with
snow
[ When a vehicle suddenly appears
from a curve
[ When the vehicle is tilted from a flat
tyre or being towed
[ : K H Q / D Q H . H H S L Q J $ V V L V W V \ V W H P
warning light illuminates
[ When the light from the oncoming or
front vehicle is not detected because
of exhaust fume, smoke, fog, snow,
etc.
[ When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged
3. When the forward visibility is poor.
Such examples may include:
[ When the headlights of an oncoming
vehicle or a vehicle in front is not
detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.)
[ When the windscreen visibility is
poor WARNING
[ 7 K H I X Q F W L R Q P D \ Q R W Z R U N D U R X Q G
seconds after starting the vehicle or
the initialization or rebooting of the
front view camera.
[ ' R Q R W D W W H P S W W R G L V D V V H P E O H
the front view camera without the
assistance of a HYUNDAI authorised
repairer technician.
If the front view camera is removed
for any reason, the system may need
to be re-calibrated. We recommend
that the system be inspected by a
HYUNDAI authorised repairer.
[ , I W K H Z L Q G V F U H H Q R I \ R X U Y H K L F O H
is replaced, most likely the front
view camera will need to be
re-calibrated. If this occurs, have
your vehicle inspected and have the
system re-calibrated by a HYUNDAI
authorised repairer.
[ % H F D U H I X O W K D W Z D W H U G R H V QT W J H W L Q W R
front view camera unit and do not
remove or damage related parts of
High Beam Assist system.
[ ' R Q R W S O D F H R E M H F W V R Q W K H F U D V K
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.
[ $ W W L P H V + L J K % H D P $ V V L V W P D \
not work properly. The system is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.
[ : K H Q W K H V \ V W H P G R H V Q R W R S H U D W H
normally, change the light position
manually between the high beam and
low beam.
Page 196 of 649
5-55
05
AUTO (Automatic) control
(if equipped)
The rain sensor located at the top of the
windscreen glass senses the amount of
rainfall and controls the wiping cycle for
the proper interval. The wiper operation
time will be automatically controlled,
depending on rainfall.
When the rain stops, the wiper stops. To
vary the speed setting, turn the speed
control knob.
If the wiper switch is set in AUTO mode
when the ignition switch is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WARNING
To avoid personal injury from the
windscreen wipers, when the engine
is running and the windscreen wiper
switch is placed in the AUTO mode:
Do not touch the upper end of the
windscreen glass facing the rain sensor.
Do not wipe the top of the windscreen
glass with a damp or wet cloth.
Do not put pressure on the windscreen
glass.
NOTICE
When washing the vehicle, set the
Z L S H U V Z L W F K L Q W K H 2 ) ) S R V L W L R Q W R V W R S
the auto wiper operation. The wiper
may operate and be damaged if the
switch is set in the AUTO mode whilst
washing the vehicle.
Do not remove the sensor cover
located at the top of the passenger side
windscreen glass. Damage to system
parts could occur and may not be
covered by your vehicle warranty.
Windscreen washers
OTLE045168
In the OFF (O) position, pull the lever
gently toward you to spray washer
fluid on the windscreen and to run the
wipers 1-3 cycles. The spray and wiper
operation will continue until you release
the lever. If the washer does not work,
you may need to add washer fluid to the
washer fluid reservoir.
WARNING
When the outside temperature is
below freezing, ALWAYS warm the
windscreen using the defroster to
prevent the washer fluid from freezing
on the windscreen and obscuring your
vision which could result in an accident
and serious injury or death.
Page 202 of 649
5-61
05
i Information
2 S H U D W L Q J W K H V \ V W H P S U L P D U L O \ L Q ) U H V K
P R G H L V U H F R P P H Q G H G 8 V H 5 H F L U F X O D W L R Q
mode temporarily only when needed.
Prolonged operation of the heater in
5 H F L U F X O D W L R Q P R G H D Q G Z L W K R X W W K H $ &
2 1 F D Q F D X V H I R J J L Q J R I W K H Z L Q G V F U H H Q
, Q D G G L W L R Q S U R O R Q J H G X V H R I W K H $ &
2 1 L Q 5 H F L U F X O D W L R Q P R G H P D \ U H V X O W L Q
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
mode for a prolonged period of
time may cause drowsiness to the
occupants in the cabin. This may lead
to loss of vehicle control which may
lead to an accident.
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
P R G H Z L W K W K H $ & 2 ) ) P D \ D O O R Z
humidity to increase inside the cabin.
This may cause condensation to
accumulate on the windscreen and
obscure visibility.
[ ' R Q R W V O H H S L Q \ R X U Y H K L F O H R U
remain parked in your vehicle with
the windows up and either the
heater or the air conditioning ON for
prolonged periods of time. Doing so
may increase the levels of carbon
dioxide in the cabin which may lead
to serious injury or death.
Fan speed control
OBC3050106
Turn the knob to the right to increase
the fan speed and airflow. Turn the knob
to the left to decrease fan speed and
airflow.
Setting the fan speed control knob to
the “0” position turns off the fan.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Air conditioning (if equipped)
OBC3050107
Press the A/C button to turn the air
conditioning system on (indicator light
will illuminate). Press the button again to
turn the air conditioning system off.
Page 206 of 649
5-65
05
WARNING
Vehicles equipped with R-1234yf
Since the refrigerant is
mildly flammable and
operated at high pressure,
the air conditioning system
should only be serviced by
trained and certified
technicians (Refer to the
6 $ ( - , W L V L P S R U W D Q W
that the correct type and
amount of oil and
refrigerant are used.
All refrigerants should be reclaimed
with proper equipment.
Venting refrigerants directly to the
atmosphere is harmful to individuals
D Q G H Q Y L U R Q P H Q W ) D L O X U H W R K H H G W K H V H
warnings can lead to serious injuries.
OBC3050052
Air Conditioning refrigerant label
You can find out which air conditioning
refrigerant is applied to your vehicle on
the label located inside of the bonnet.
[ 7 \ S H %
OHYK059001
OHYK059004
„Example [ 7 \ S H $
Each symbol and specification on the air
conditioning refrigerant label are
represented as below:
1. Classification of refrigerant
2. Amount of refrigerant
3. Classification of compressor lubricant
4. Caution
5. Flammable refrigerant
6. To require registered technician to
service air conditioning system
7. Service manual
Page 212 of 649
5-71
05
i Information
2 S H U D W L Q J W K H V \ V W H P S U L P D U L O \ L Q ) U H V K
P R G H L V U H F R P P H Q G H G 8 V H 5 H F L U F X O D W L R Q
mode temporarily only when needed.
Prolonged operation of the heater in
5 H F L U F X O D W L R Q P R G H D Q G Z L W K R X W W K H $ &
2 1 F D Q F D X V H I R J J L Q J R I W K H Z L Q G V F U H H Q
, Q D G G L W L R Q S U R O R Q J H G X V H R I W K H $ &
2 1 L Q 5 H F L U F X O D W L R Q P R G H P D \ U H V X O W L Q
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
[ Continued use of the climate control
system operation in Recirculation
mode for a prolonged period of
time may cause drowsiness to the
occupants in the cabin. This may lead
to loss of vehicle control which may
lead to an accident.
[ Continued use of the climate control
system operation in Recirculation
P R G H Z L W K W K H $ & 2 ) ) P D \ D O O R Z
humidity to increase inside the cabin.
This may cause condensation to
accumulate on the windscreen and
obscure visibility.
[ Do not sleep in your vehicle or
remain parked in your vehicle with
the windows up and either the
heater or the air conditioning ON for
prolonged periods of time. Doing so
may increase the levels of carbon
dioxide in the cabin which may lead
to serious injury or death.
Fan speed control
OBC3050115R
Push the switch to up to increase the fan
speed and airflow. Push the switch to
down to decrease fan speed and airflow.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Page 217 of 649
5-76
Convenient features
WARNING
Vehicles equipped with R-1234yf
Since the refrigerant is
mildly flammable and
operated at high pressure,
the air conditioning system
should only be serviced by
trained and certified
technicians (Refer to the
6 $ ( - , W L V L P S R U W D Q W
that the correct type and
amount of oil and
refrigerant are used.
All refrigerants should be reclaimed
with proper equipment.
Venting refrigerants directly to the
atmosphere is harmful to individuals
D Q G H Q Y L U R Q P H Q W ) D L O X U H W R K H H G W K H V H
warnings can lead to serious injuries.
OBC3050052
Air Conditioning refrigerant label
You can find out which air conditioning
refrigerant is applied to your vehicle on
the label located inside of the bonnet.
[ 7 \ S H %
OHYK059001
OHYK059004
„Example [ 7 \ S H $
Each symbol and specification on the air
conditioning refrigerant label is
represented as below:
1. Classification of refrigerant
2. Amount of refrigerant
3. Classification of compressor lubricant
4. Caution
5. Flammable refrigerant
6. To require registered technician to
service air conditioning system
7. Service manual