air condition HYUNDAI I20 2023 User Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 113 of 649
4-18
Instrument cluster
Immobiliser indicator
light (with smart key)
(if equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V I R U X S
W R V H F R Q G V
[ When the vehicle detects the smart
key in the vehicle with the Engine
Start/Stop button in the ACC or ON
position.
- At this time, you can start the engine.
- The indicator light goes off after
starting the engine.
7 K L V L Q G L F D W R U O L J K W E O L Q N V I R U D I H Z
V H F R Q G V
[ When the smart key is not in the
vehicle.
- At this time, you cannot start the
engine.
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V I R U
V H F R Q G V D Q G J R H V R I I
[ If the smart key is in the vehicle and
the Engine Start/Stop button is ON,
but the vehicle cannot detect the
smart key.
In this case, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
7 K L V L Q G L F D W R U O L J K W E O L Q N V
[ When there is a malfunction with the
immobiliser system.
In this case, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
Turn signal indicator
light
7 K L V L Q G L F D W R U O L J K W E O L Q N V
[ When you operate the turn signals.
If any of the following occur, there may
be a malfunction with the turn signal
system.
- The turn signal indicator light
illuminates but does not blink
- The turn signal indicator light blinks
rapidly
- The turn signal indicator light does not
illuminate at all
If any of these conditions occur, we
recommend that you have your vehicle
inspected by a HYUNDAI authorised
repairer.
Low beam indicator light
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
When the headlamps are on.
High beam indicator light
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
[ When the headlamps are on and in the
high beam position.
[ When the turn signal lever is pulled
into the Flash-to-Pass position.
Page 114 of 649
4-19
04
High Beam Assist
indicator light (if
equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
When the high-beam is on with the light
switch in the AUTO position.
If your vehicle detects oncoming or
preceding vehicles, High Beam Assist
will switch the high beam to low beam
automatically.
For more details, refer to “High Beam
Assist (HBA)” section in chapter 5.
Light ON indicator light
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
When the tail lights is on.
Front fog indicator light
(if equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
When the front fog lights are on.
Rear fog indicator light
(if equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
When the rear fog lights are on.
Forward Safety warning
light (if equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
[ When you set the ignition switch or
Engine Start/Stop button to the ON
position.
- The Forward Safety warning light
illuminates for approximately 3
seconds and then goes off.
[ Whenever there is a malfunction with
Forward Collision-Avoidance Assist.
If this occurs, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
For more details, refer to “Forward
Collision-Avoidance Assist (FCA)”
section in chapter 7.
Lane Safety indicator
light (if equipped)
7 K L V L Q G L F D W R U O L J K W L O O X P L Q D W H V
[ [Green] When the function operating
conditions are satisfied.
[ [White] The function operating
conditions are not satisfied.
[ [Yellow] Whenever there is a
malfunction with Lane Keeping Assist.
If this occurs, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
For more details, refer to “Lane Keeping
Assist (LKA)” section in chapter 7.
Page 119 of 649
4-24
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended lubricants and
capacities" section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
NOTICE
If the message is displayed
continuously after adding the engine
oil and travelling approximately 31~
62 mile (50~100 km) after the engine
warms up, we recommend that the
system be checked by a HYUNDAI
authorised repairer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check headlight (if equipped)
This warning message is displayed if the
headlamps are not operating properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check brake light (if equipped)
This warning message is displayed if the
stop lamps are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check Active Air Flap system (if
equipped)
This message is displayed in the
following situations:
- There is a malfunction with the
actuator flap
- There is a malfunction with the
actuator air flap controller
- The air flap does not open
When all of the above conditions are
fixed, the warning will disappear.
Page 143 of 649
5
Wipers and washers ...................................................................................... 5-54Windscreen wipers .................................................................................................. 5-54
Windscreen washers ............................................................................................... 5-55
Rear window wiper and washer switch ................................................................. 5-56
Manual climate control system .................................................................... 5-57Heating and air conditioning .................................................................................. 5-58
System operation .................................................................................................... 5-62
System maintenance .............................................................................................. 5-64
Automatic climate control system ...............................................................5-66Automatic heating and air conditioning ................................................................ 5-67
Manual heating and air conditioning ..................................................................... 5-68
System operation ..................................................................................................... 5-72
System maintenance ............................................................................................... 5-75
Windscreen defrosting and defogging ......................................................... 5-77Manual climate control system ............................................................................... 5-77
Automatic climate control system ..........................................................................5-78
Auto defogging system (only for automatic climate control system) ..................5-79
Defroster .................................................................................................................. 5-80
Storage compartment .................................................................................. 5-82Centre console storage ........................................................................................... 5-82
Glove box ................................................................................................................. 5-83
Interior features ............................................................................................ 5-84Ashtray ..................................................................................................................... 5-84
Cup holder ............................................................................................................... 5-84
Sliding armrest ........................................................................................................ 5-85
Sunvisor ................................................................................................................... 5-85
Power outlet ............................................................................................................ 5-86
USB charger ............................................................................................................. 5-87
Wireless mobile phone charging system ............................................................... 5-87
Clock ........................................................................................................................ 5-90
Coat hook ................................................................................................................. 5-90
Floor mat anchor(s) .................................................................................................. 5-91
Luggage net (holder) ............................................................................................... 5-92
Cargo area cover ..................................................................................................... 5-92
Page 189 of 649
5-48
Convenient features
WARNING
If the function does not work properly,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. Do not attempt to inspect or
replace the wiring yourself.
Low Beam Assist-Static light
Whilst driving a corner, for greater
visibility and safety, either the left or
right side Low Beam Assist-Static light
will turn on automatically. The Low
Beam Assist-Static light will turn on
when one of the following conditions
occurs.
[ Vehicle speed is less than 6 mph (10
km/h) and steering wheel angle is
turned approximately 80 degrees with
the low beam on.
[ Vehicle speed is between 6 mph
(10 km/h) to 56 mph (90 km/h)
and steering wheel angle is turned
approximately 35 degrees with the low
beam on.
[ When the vehicle is in reverse with
one of the conditions above satisfied,
the light opposite to the direction the
steering wheel is turned will turn on.
Page 191 of 649
5-50
Convenient features
- If the light switch is pushed away
when High Beam Assist is operating,
High Beam Assist will turn off.
- If the light switch is pulled towards
you when the high beam is off, the
high beam will turn on. When you let
go of the light switch, the lever will
move to the middle and the high beam
will turn off.
- If the light switch is pulled towards
you when the high beam is on by High
Beam Assist, and High Beam Assist
will turn off.
- If the light switch is placed to the
headlight position (
), High Beam
Assist will turn off and the low beam
will be on continuously.
When High Beam Assist is operating, the
high beam switches to low beam in the
following conditions.
- When the headlight of an on-coming
vehicle is detected.
- When the tail light of a vehicle in front
is detected.
- When the headlight or tail light of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light is
bright enough that high beams are not
required.
- When streetlights or other lights are
detected.
- When the light switch is not in the
AUTO position.
- When High Beam Assist is off.
- When the vehicle speed is below 19
mph (30 km/h).
System malfunction and
limitations
System malfunction
OTM050218L
When High Beam Assist is not working
properly, the warning message will come
on for a few seconds. After the message
disappears, the master warning light
(
) will illuminate.
We recommend that you take your
vehicle to a HYUNDAI authorised
repairer and have the system checked.
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an
on-coming vehicle or a vehicle in
front is dim. Such examples may
include:
[ When the headlights of an oncoming
vehicle or the tail lights of a vehicle
in front is covered with dust, snow,
or water
[ When the headlights on an
R Q F R P L Q J Y H K L F O H D U H 2 ) ) E X W W K H
fog lights are ON)
Page 192 of 649
5-51
05
2. When the front view camera is
adversely affected by an external
condition. Such examples may
include:
[ When the vehicle’s headlights have
been damaged or not repaired
properly
[ When the vehicle headlights are not
aimed properly
[ When the vehicle is driven on a
narrow curved road or rough road
[ When the vehicle is driven on an
uphill road or downhill road
[ When only part of the vehicle in front
is visible on a crossroad or curved
road
[ When there is a traffic light,
reflecting sign, flashing sign or mirror
[ When the road conditions are bad
such as being wet or covered with
snow
[ When a vehicle suddenly appears
from a curve
[ When the vehicle is tilted from a flat
tyre or being towed
[ : K H Q / D Q H . H H S L Q J $ V V L V W V \ V W H P
warning light illuminates
[ When the light from the oncoming or
front vehicle is not detected because
of exhaust fume, smoke, fog, snow,
etc.
[ When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged
3. When the forward visibility is poor.
Such examples may include:
[ When the headlights of an oncoming
vehicle or a vehicle in front is not
detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.)
[ When the windscreen visibility is
poor WARNING
[ 7 K H I X Q F W L R Q P D \ Q R W Z R U N D U R X Q G
seconds after starting the vehicle or
the initialization or rebooting of the
front view camera.
[ ' R Q R W D W W H P S W W R G L V D V V H P E O H
the front view camera without the
assistance of a HYUNDAI authorised
repairer technician.
If the front view camera is removed
for any reason, the system may need
to be re-calibrated. We recommend
that the system be inspected by a
HYUNDAI authorised repairer.
[ , I W K H Z L Q G V F U H H Q R I \ R X U Y H K L F O H
is replaced, most likely the front
view camera will need to be
re-calibrated. If this occurs, have
your vehicle inspected and have the
system re-calibrated by a HYUNDAI
authorised repairer.
[ % H F D U H I X O W K D W Z D W H U G R H V QT W J H W L Q W R
front view camera unit and do not
remove or damage related parts of
High Beam Assist system.
[ ' R Q R W S O D F H R E M H F W V R Q W K H F U D V K
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.
[ $ W W L P H V + L J K % H D P $ V V L V W P D \
not work properly. The system is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.
[ : K H Q W K H V \ V W H P G R H V Q R W R S H U D W H
normally, change the light position
manually between the high beam and
low beam.
Page 199 of 649
5-58
Convenient features
Heating and air conditioning
1. Start the engine.
2. Set the mode to the desired position.
To improve the effectiveness of heating and cooling :
- Heating:
- Cooling:
3. Set the temperature control to the desired position.
4. Set the air intake control to Fresh mode.
5. Set the fan speed control to the desired speed.
6. If air conditioning is desired, turn the air conditioning system on.
Mode selection
OBC3050102R
Page 202 of 649
5-61
05
i Information
2 S H U D W L Q J W K H V \ V W H P S U L P D U L O \ L Q ) U H V K
P R G H L V U H F R P P H Q G H G 8 V H 5 H F L U F X O D W L R Q
mode temporarily only when needed.
Prolonged operation of the heater in
5 H F L U F X O D W L R Q P R G H D Q G Z L W K R X W W K H $ &
2 1 F D Q F D X V H I R J J L Q J R I W K H Z L Q G V F U H H Q
, Q D G G L W L R Q S U R O R Q J H G X V H R I W K H $ &
2 1 L Q 5 H F L U F X O D W L R Q P R G H P D \ U H V X O W L Q
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
mode for a prolonged period of
time may cause drowsiness to the
occupants in the cabin. This may lead
to loss of vehicle control which may
lead to an accident.
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
P R G H Z L W K W K H $ & 2 ) ) P D \ D O O R Z
humidity to increase inside the cabin.
This may cause condensation to
accumulate on the windscreen and
obscure visibility.
[ ' R Q R W V O H H S L Q \ R X U Y H K L F O H R U
remain parked in your vehicle with
the windows up and either the
heater or the air conditioning ON for
prolonged periods of time. Doing so
may increase the levels of carbon
dioxide in the cabin which may lead
to serious injury or death.
Fan speed control
OBC3050106
Turn the knob to the right to increase
the fan speed and airflow. Turn the knob
to the left to decrease fan speed and
airflow.
Setting the fan speed control knob to
the “0” position turns off the fan.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Air conditioning (if equipped)
OBC3050107
Press the A/C button to turn the air
conditioning system on (indicator light
will illuminate). Press the button again to
turn the air conditioning system off.
Page 203 of 649
5-62
Convenient features
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.
2 S H U D W L R Q 7 L S V
[ 7 R N H H S G X V W R U X Q S O H D V D Q W I X P H V
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.
[ 7 R S U H Y H Q W L Q W H U L R U I R J R Q W K H
windscreen, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-134a or R1234yf refrigerant.
1. Start the engine.
2. Push the air conditioning button.
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
i Information
OBC3050052
< R X U Y H K L F O H L V I L O O H G Z L W K 5 D R U
5 \ I D F F R U G L Q J W R W K H U H J X O D W L R Q L Q
your country at the time of production.
< R X F D Q I L Q G R X W Z K L F K D L U F R Q G L W L R Q L Q J
refrigerant is applied to your vehicle on
the label located inside of the bonnet.