low beam HYUNDAI I20 2023 User Guide

9-63
09
OBC3090039
OBC3TN091006
„CUV
7XUQVLJQDOOLJKW
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3RVLWLRQOLJKW'D\WLPHUXQQLQJOLJKW
LIHTXLSSHG
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.

9-66
Maintenance
3. Draw vertical lines (Vertical lines
passing through respective head
light centres) and a horizontal line
(Horizontal line passing through
centre of head lamps) on the screen.
4. With the headlight and battery in
normal condition, aim the headlights
so the brightest portion falls on the
horizontal and vertical lines.
5. To aim the low beam left or
right, turn the driver clockwise or
counterclockwise. To aim the low
beam up or down, turn the driver
clockwise or counterclockwise.
To aim the high beam up or
down, turn the driver clockwise or
counterclockwise.Front fog light aiming (if equipped)
OBC3090042
The front fog light can be aimed as the
same manner of the head lights aiming.
With the front fog lights and battery
normal condition, aim the front fog
lights. To aim the front fog light up
or down, turn the driver clockwise or
counterclockwise.

9-67
09
Aiming point
OBC3090043

H1 : Lighting centre Ground clearance of Headlight Low & High BeamH3 : Lighting centre Ground clearance of Front fog lightW1 : Lighting centre Distance between Headlight Low & High BeamW3 : Lighting centre Distance between Front fog light
1. Headlamp (LOW - H1, W1 / HIGH BEAM - H2, W2) mm(in.)
Vehicle condition “H1” “H2” “W1” “W2”
Without driver (HAL 2 MFR) 654.9 (25.8) 654.9 (25.8) 1320 (52.0) 1320 (52.0)
Without driver (LED 4 MFR) 670.4 (26.4) 622.3 (24.5) 1396.8 (55.0) 1233.6 (48.57)
With driver (HAL 2 MFR) 646.9 (25.5) 646.9 (25.5) 1320 (52.0) 1320 (52.0)
With driver (LED 4 MFR) 662.4 (26.1) 614.3 (24.2) 1396.8 (55.0) 1233.6 (48.57)
2. Fog lamp (H3, W3)
Vehicle condition “H3” “W3”
Without driver 352 (13.9) 1434.4 (56.5)
With driver 344 (13.6) 1434.4 (56.5)

9-68
Maintenance
Head lamp low beam
OBC3090059
„ Based on 10m screen
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the
horizontal aiming.
4. If the head lamp leveling device is equipped, adjust the head lamp levelling device
switch with 0 position.