Eco HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 620 of 649
9-61
09
OLMB073042L
WARNING
[ Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.
[ Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.
[ Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
[ Never touch the glass with bare
hands. Residual oil may cause the bulb
to overheat and burst when lit.
[ A bulb should be operated only when
installed in a headlight.
[ If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
i Information
: H U H F R P P H Q G W K D W W K H K H D G O L J K W D L P L Q J
E H D G M X V W H G D I W H U D Q D F F L G H Q W R U D I W H U W K H
K H D G O L J K W D V V H P E O \ L V U H L Q V W D O O H G
❈ 7 U D I I L F & K D Q J H ) R U ( X U R S H
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direction,
this asymmetric part will dazzle
oncoming car driver. To prevent dazzle,
ECE regulation demands several
technical solutions (ex. automatic
change system, adhesive sheet, down
aiming). This headlamps are designed
not to dazzle opposite drivers.
So, you need not change your
headlamps in a country with the
opposite traffic direction.
Page 622 of 649
9-63
09
OBC3090039
OBC3TN091006
„CUV
7 X U Q V L J Q D O O L J K W
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3 R V L W L R Q O L J K W ' D \ W L P H U X Q Q L Q J O L J K W
L I H T X L S S H G
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
Page 623 of 649
9-64
Maintenance
Type D (LED)
OBC3090037
Type E (LED)-N line
OBC3TN091001
(1) headlight (Low)
(2) headlight (High)
(3) Static Bending Light
(4) Turn signal light
(5) Daytime running light & Position light
(6) Front fog light
Type F (LED)-CUV
OBC3V091005
(1) Headlight (Low)
(2) Headlight (High)
(3) Static Bending Light
(4) Daytime running light & Position &
Turn signal light
+ H D G O L J K W 3 R V L W L R Q O L J K W 7 X U Q V L J Q D O
O L J K W ' D \ W L P H U X Q Q L Q J O L J K W / R Z
E H D P D V V L V W V W D W L F O L J K W E X O E U H S O D F H
P H Q W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
Page 629 of 649
9-70
Maintenance
Side repeater light replacement
Type A
OBC3090044
If the LED lamp does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
OAC3089047TU
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.
Page 633 of 649
![HYUNDAI I20 2023 Owners Manual 9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the](/img/35/56129/w960_56129-632.png "HYUNDAI I20 2023 Owners Manual 9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the")
9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7 X U Q V L J Q D O O L J K W
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
7 D L O O L J K W 6 W R S O L J K W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
OBC3090050
[1] : Rear Fog Light, [2] : Back-up Light
5 H D U I R J O L J K W
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.
% D F N X S O L J K W
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
4. Take the light assembly out.
Page 636 of 649
9-77
09
Type D
OBC3V091006
(1) Turn signal lamp
(2) Tail/Stop light
(3) Rear fog light/Rear reflection light
7 X U Q V L J Q D O O D P S 7 D L O O L J K W 6 W R S
O L J K W
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit.
The LED lamp has to be replaced with
the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
OBC3V091004
[1] : Rear Fog Light
5 H D U I R J O L J K W 5 H D U U H I O H F W L R Q O L J K W
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.
Page 641 of 649
9-82
Maintenance
Finish damage repair
Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major repair
expense.
NOTICE
If your vehicle is damaged and requires
any metal repair or replacement,
be sure the body shop applies anti-
corrosion materials to the parts
repaired or replaced.
NOTICE
Matte paint finish vehicle
(if equipped)
In case of matte paint finish vehicles,
it is impossible to modify only the
damaged area and repair of the whole
part is necessary. If the vehicle is
damaged and painting is required, we
recommend that you have your vehicle
maintained and repaired by a HYUNDAI
authorised repairer. Take extreme care,
as it is difficult to restore the quality
after the repair.
Bright-metal maintenance
[ 7 R U H P R Y H U R D G W D U D Q G L Q V H F W V X V H
a tar remover, not a scraper or other
sharp object.
[ 7 R S U R W H F W W K H V X U I D F H V R I E U L J K W P H W D O
parts from corrosion, apply a coating
of wax or chrome preservative and rub
to a high luster.
[ ' X U L Q J Z L Q W H U Z H D W K H U R U L Q F R D V W D O
areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, accelerated
rusting can occur on underbody parts
such as the fuel lines, frame, floor pan
and exhaust system, even though they
have been treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter.
Pay special attention to these areas
because it is difficult to see all the mud
and dirt. It will do more harm than good
to wet down the road grime without
removing it. The lower edges of doors,
rocker panels, and frame members have
drain holes that should not be allowed
to clog with dirt; trapped water in these
areas can cause rusting.
Page 644 of 649
9-85
09
Keep your garage dry
Don’t park your vehicle in a damp,
poorly ventilated garage. This creates
a favorable environment for corrosion.
This is particularly true if you wash your
vehicle in the garage or drive it into the
garage when it is still wet or covered
with snow, ice or mud. Even a heated
garage can contribute to corrosion
unless it is well ventilated so moisture is
dispersed.
Keep paint and trim in good condition
Scratches or chips in the finish should
be covered with “touch-up” paint as
soon as possible to reduce the possibility
of corrosion. If bare metal is showing
through, the attention of a qualified
body and paint shop is recommended.
Bird droppings : Bird droppings are
highly corrosive and may damage
painted surfaces in just a few hours.
Always remove bird droppings as soon
as possible.
Don’t neglect the interior
Moisture can collect under the floor
mats and carpeting to cause corrosion.
Check under the mats periodically to be
sure the carpeting is dry. Use particular
care if you carry fertilizers, cleaning
materials or chemicals in the vehicle.
These should be carried only in proper
containers and any spills or leaks should
be cleaned up, flushed with clean water
and thoroughly dried.
Interior care
Interior general precautions
Prevent chemicals such as perfume,
cosmetic oil, sun cream, hand cleaner
and air freshener from contacting the
interior parts because they may cause
damage or discolouration. If they do
contact the interior parts, wipe them off
immediately.
See the instructions that follow for the
proper way to clean vinyl.
NOTICE
Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as this may damage them.
NOTICE
When cleaning leather products
(steering wheel, seats etc.), use neutral
detergents or low alcohol content
solutions. If you use high alcohol
content solutions or acid/alkaline
detergents, the colour of the leather
may fade or the surface may get
stripped off.
Page 645 of 649
9-86
Maintenance
Cleaning the upholstery and interior
trim
9 L Q \ O L I H T X L S S H G
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl surfaces with a vinyl cleaner.
) D E U L F L I H T X L S S H G
Remove dust and loose dirt from
fabric with a whisk broom or vacuum
cleaner. Clean with a mild soap solution
recommended for upholstery or carpets.
Remove fresh spots immediately with
a fabric spot cleaner. If fresh spots do
not receive immediate attention, the
fabric can be stained and its colour
can be affected. Also, its fire-resistant
properties can be reduced if the material
is not properly maintained.
NOTICE
Using anything but recommended
cleaners and procedures may affect the
fabric’s appearance and fire-resistant
properties.
/ H D W K H U L I H T X L S S H G
[ ) H D W X U H V R I 6 H D W / H D W K H U
- Leather is made from the outer skin
of an animal, which goes through a
special process to be available for
use. Since it is a natural product,
each part differs in thickness or
density.
Wrinkles may appear as a natural
result of stretching and shrinking
depending on the temperature and
humidity.
- The seat is made of stretchable
fabric to improve comfort.
- The parts contacting the body are
curved and the side supporting
area is high which provides driving
comfort and stability.
- Wrinkles may appear naturally
from usage. It is not a fault of the
products.
CAUTION
[ : U L Q N O H V R U D E U D V L R Q V Z K L F K D S S H D U
naturally from usage are not covered
by warranty.
[ % H O W V Z L W K P H W D O O L F D F F H V V R U L H V
zippers or keys inside the back
pocket may damage the seat fabric.
[ 0 D N H V X U H Q R W W R Z H W W K H V H D W , W P D \
change the nature of natural leather.
[ - H D Q V R U F O R W K H V Z K L F K F R X O G E O H D F K
may contaminate the surface of the
seat covering fabric.
Page 646 of 649
9-87
09
[ & D U L Q J I R U W K H O H D W K H U V H D W V
- Vacuum the seat periodically to
remove dust and sand on the seat. It
will prevent abrasion or damage of
the leather and maintain its quality.
- Wipe the natural leather seat cover
often with dry or soft cloth.
- Use of proper leather protector may
prevent abrasion of the cover and
helps maintain the colour. Be sure to
read the instructions and consult a
specialist when using leather coating
or protective agent.
- Light coloured (such as beige
or cream beige) leather is easily
contaminated and the stain
is noticeable. Clean the seats
frequently.
- Avoid wiping with wet cloth. It may
cause the surface to crack.
[ & O H D Q L Q J W K H O H D W K H U V H D W V
- Remove all contaminations instantly.
Refer to instructions below for
removal of each contaminant.
- Cosmetic products (sunscreen,
foundation, etc.)
Apply cleansing cream on a cloth and
wipe the contaminated spot. Wipe
off the cream with a wet cloth and
remove water with a dry cloth.
- Beverages (coffee, soft drink, etc.)
Apply a small amount of neutral
detergent and wipe until
contaminations do not smear.
- Oil
Remove oil instantly with absorbable
cloth and wipe with stain remover
used only for natural leather.
- Chewing gum
Harden the gum with ice and remove
gradually. Cleaning the lap/shoulder belt
webbing
Clean the belt webbing with any
mild soap solution recommended for
cleaning upholstery or carpet. Follow
the instructions provided with the soap.
Do not bleach or re-dye the webbing
because this may weaken it.
Cleaning the interior window glass
If the interior glass surfaces of the
vehicle become fogged (that is, covered
with an oily, greasy or waxy film), they
should be cleaned with glass cleaner.
Follow the directions on the glass
cleaner container.
NOTICE
Do not scrape or scratch the inside of
the rear window. This may result in
damage to the rear window defroster
grid.