service HYUNDAI I20 2023 Owner's Manual

8-15
08
If the indicators do not extinguish after
a few minutes, it is recommended to
contact the nearest authorised HYUNDAI
dealer.
Each wheel is equipped with a tyre
pressure sensor mounted inside the tyre
behind the valve stem (except for the
spare tyre). You must use TPMS specific
wheels. It is recommended that you
always have your tyres serviced by a
HYUNDAI authorised repairer.
You may not be able to identify a tyre
with low pressure by simply looking at it.
Always use a good quality tyre pressure
gauge to measure. Please note that a
tyre that is hot (from being driven) will
have a higher pressure measurement
than a tyre that is cold.
A cold tyre means the vehicle has been
sitting for 3 hours and driven for less
than 1 mile (1.6 km) in that 3 hour period.
Allow the tyre to cool before measuring
the inflation pressure. Always be sure
the tyre is cold before inflating to the
recommended pressure.
WARNING

[The TPMS cannot alert you to severe
and sudden tyre damage caused by
external factors such as nails or road
debris.

[If you feel any vehicle instability,
immediately take your foot off
the accelerator, apply the brakes
gradually with light force, and slowly
move to a safe position off the road.
WARNING
Tampering with, modifying, or disabling
the Tyre Pressure Monitoring System
(TPMS) components may interfere
with the system’s ability to warn the
driver of low tyre pressure conditions
and/or TPMS malfunctions. Tampering
with, modifying, or disabling the Tyre
Pressure Monitoring System (TPMS)
components may void the warranty for
that portion of the vehicle.
WARNING

[Do not modify the vehicle; it may
interfere with the TPMS function.

[The wheels on the market do not
have a TPMS sensor.

[For your safety, we recommend that
you use parts for replacement from a
HYUNDAI authorised repairer.

[If you use the wheels on the market,
use a TPMS sensor approved by a
HYUNDAI dealer or the equivalent
approved for your vehicle. If your
vehicle is not equipped with a TPMS
sensor or TPMS does not work
properly, you may fail the periodic
vehicle inspection conducted in your
country.

8-17
08
Changing tyres
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:

[Do not get under a vehicle that is
supported by a jack.

[NEVER attempt to change a tyre in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tyre. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.

[Be sure to use the jack provided with
the vehicle.

[ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.

[Do not start or run the engine whilst
the vehicle is on the jack.

[Do not allow anyone to remain in the
vehicle whilst it is on the jack.

[Keep children away from the road
and the vehicle.
Follow these steps to change your
vehicle’s tyre:
1. Park on a level, firm surface.
2. Move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tyre from
the vehicle.
OBC3080005
[A] : Block
5. Block both the front and rear of the
tyre diagonally opposite of the tyre
you are changing.
OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tyre has
been raised off of the ground.

8-19
08
If you have a tyre gauge, check the tyre
pressure (see “Tyres and Wheels” in
chapter 2 for tyre pressure instructions.).
If the pressure is lower or higher than
recommended, drive slowly to the
nearest service station and adjust it to
the recommended pressure. Always
reinstall the valve cap after checking
or adjusting tyre pressure. If the cap
is not replaced, air may leak from the
tyre. If you lose a valve cap, buy another
and install it as soon as possible. After
changing tyres, secure the flat tyre and
return the jack and tools to their proper
storage locations.
NOTICE

[ &KHFNWKHW\UHSUHVVXUHDVVRRQ
as possible after installing a spare
tyre. Adjust it to the recommended
pressure.

[ &KHFNDQGWLJKWHQWKHZKHHOOXJQXWV
after driving over 50 km if tyres are
replaced. Re-check the tyre wheel
lug nuts after driving over 1,000 km.
CAUTION
Your vehicle has metric threads on
the studs and lug nuts. Make certain
during tyre changing that the same
nuts that were removed are reinstalled.
If you have to replace your lug nuts
make sure they have metric threads to
avoid damaging the studs and ensure
the wheel is properly secured to the
hub. We recommend that you consult
a HYUNDAI authorised repairer for
assistance.
If any of the equipment such as the jack,
lug nuts, studs, or other equipment is
damaged or in poor condition, do not
attempt to change the tyre and call for
assistance.
Use of compact spare tyres
(if equipped)
Compact spare tyres are designed for
emergency use only. Drive carefully
on the compact spare tyre and always
follow the safety precautions.
WARNING
To prevent compact spare tyre failure
and loss of control possibly resulting in
an accident:

[ 8VHWKHFRPSDFWVSDUHW\UHRQO\LQDQ
emergency.

[ 1(9(5RSHUDWH\RXUYHKLFOHRYHU
mph (80 km/h).

[ 'RQRWH[FHHGWKHYHKLFOH
TV
maximum load rating or the load
carrying capacity shown on the
sidewall of the compact spare tyre.

[ 'RQRWXVHWKHFRPSDFWVSDUHW\UH
continuously. Repair or replace the
original tyre as soon as possible to
avoid failure of the compact spare
tyre.

8-31
08
WARNING
Carbon monoxide
Do not leave your vehicle running in
a poorly ventilated area for extended
periods of time.
Carbon monoxide poisoning and
suffocation can occur.
Distributing the sealant
11. Immediately drive approximately
4~6miles (7~10km or, about 10 mins)
to evenly distribute the sealant in the
tyre.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
Whilst driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off the
vehicle on the side of the road.
Call for road side service or towing.
When you use the Tyre Mobility Kit, the
tyre pressure valve and wheel may be
damaged by sealant, remove the sealant
stained. We recommend that the tyre
pressure valve and wheel be inspected
by an authorized HYUNDAI dealer.

Checking the tyre inflation
pressure
1. After driving approximately 4 ~6miles
(7~10km or about 10min), stop at a
safety location.
2. Connect connection hose (10) of the
compressor directly to the tyre valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tyre inflation pressure to
the recommended tyre inflation.
With the ignition switched on, proceed
as follows.
- To increase the inflation pressure :
Switch on the compressor, position
I. To check the current inflation
pressure setting, briefly switch off
the compressor.
i Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tyre pressure,
the compressor needs to be turned off.
NOTICE
- Tyre pressure valve
We recommend that you use the
sealant of tyre mobility kit from a
HYUNDAI authorised repairer. The
sealant on the tyre pressure valve and
wheel should be removed when you
replace the tyre with a new one and
we recommend that the tyre pressure
valve be inspected by an authorized
HYUNDAI dealer.

8-32
Emergency situations
Towing service
OBC3080014
[A] : Dolly
If emergency towing is necessary,
we recommend having it done by a
HYUNDAI authorised repairer or a
commercial tow-truck service.
Proper lifting and towing procedures
are necessary to prevent damage to
the vehicle. The use of wheel dollies or
flatbed is recommended.
It is acceptable to tow the vehicle with
the rear wheels on the ground (without
dollies) and the front wheels off the
ground.
If any of the loaded wheels or
suspension components are damaged or
the vehicle is being towed with the front
wheels on the ground, use a towing dolly
under the front wheels.
When being towed by a commercial tow
truck and wheel dollies are not used, the
front of the vehicle should always be
lifted, not the rear.
CAUTION

[Do not tow the vehicle with the front
wheels on the ground as this may
cause damage to the vehicle.
OBC3080015

[Do not tow with sling-type
equipment. Use wheel lift or flatbed
equipment.
OBC3080016
TOWING

8-34
Emergency situations
Emergency towing
OBC3080019
„Front
„Rear
OBC3080020
If towing is necessary, we recommend
you have it done by a HYUNDAI
authorised repairer or a commercial tow
truck service.
If towing service is not available in
an emergency, your vehicle may be
temporarily towed using a cable or chain
secured to the emergency towing hook
at the front (or rear) of the vehicle.
Use extreme caution when towing the
vehicle with a cable or chain. A driver
must be in the vehicle to steer it and
operate the brakes.
Towing in this manner may be done
only on hard-surfaced roads for a short
distance and at low speeds. Also, the
wheels, axles, power train, steering and
brakes must all be in good condition.
CAUTION
The driver must be in the vehicle for
steering and braking operations when
the vehicle is being towed. Passengers
other than the driver must not be in the
vehicle.
Always follow these emergency towing
precautions:

[Place the ignition switch in the ACC
position so the steering wheel is not
locked.

[Place the shift lever in N (Neutral).

[Release the parking brake.

[Depress the brake pedal with more
force than normal since you will have
reduced braking performance.

[More steering effort will be required
because the power steering system
will be disabled.

[Use a vehicle heavier than your own to
tow your vehicle.

[The drivers of both vehicles should
communicate with each other
frequently.

[Before emergency towing, check that
the hook is not broken or damaged.

[Fasten the towing cable or chain
securely to the hook.

[Do not jerk the hook. Apply steady and
even force.

8-38
Emergency situations
Once the data which is stored in the Pan-European eCall system is delivered to the
rescue centre to assist the driver and passengers with proper rescue operations, the
data will be deleted after rescue operation is completed.
Description of the ecall in-vehicle system
OAC3079020TU
Overview of the 112-based eCall in-vehicle system, its operation and functionalities:
refer to this section. The 112-based eCall service is a public service of general interest
and is accessible free of charge.
The 112-based eCall in-vehicle system is activated by default. It is activated
automatically by means of in- vehicle sensors in the event of a severe accident.

8-41
08
Modalities for exercising data
subject’s rights
The data subject (the vehicle’s owner)
has a right of access to data and as
appropriate to request the rectification,
erasure or blocking of data, concerning
him or her, the processing of which
does not comply with the provisions
of Directive 95/46/EC. Any third
parties to whom the data have been
disclosed have to be notified of such
rectification, erasure or blocking carried
out in compliance with this Directive,
unless it proves impossible or involves a
disproportionate effort.
The data subject has a right to complain
to the competent data protection
authority if he or she considers that his
or her rights have been infringed as a
result of the processing of his or her
personal data.
Contact service responsible for handling
access requests (if any): Not applicable
Pan-European eCall System
OBC3N080014
Elements of the Pan-European
eCall system, installed in passenger
compartment:
(1) SOS button
(2) LED
SOS button: the driver/passenger makes
an emergency call to the single duty
dispatch service by pressing the button.
LED: the red and green LED illuminates
for 3 seconds when the ignition switch
is in the ON position. After that they will
switch off at normal operation of the
system.
If there are some problems in the
system, the LED remains in red.

8-42
Emergency situations
Automatic accident reporting
OBC3080024
System operation in the event of a traffic accidentConnection with the Public Safety Answering Point(PSAP)
Emergency services
The Pan-European eCall device automatically makes an emergency call to the Public
Safety Answering Point (PSAP) for proper rescuing operations in the event of vehicle
accident.
For proper emergency services and support, the Pan-European eCall system
automatically transmits the accident data to the Public Safety Answering Point (PSAP)
when a traffic accident is detected.
In this case, the emergency call cannot be hung up by pressing the SOS button and
the Pan-European eCall system remains connected until the emergency service
officer, receiving the call, disconnects the emergency call.
In minor traffic accidents, the Pan-European eCall system may not execute an
emergency call. However, an emergency call may be made manually by pressing the
SOS button.
CAUTION
Operation of the system is impossible in case of absence of mobile transmission
and GPS and Galileo signals.

8-43
08
Manual accident reporting
OBC3080026
The driver or passenger manually can make an emergency call in the Public Safety
Answering Point(PSAP), by pressing SOS button to call the necessary emergency
services.
A call to the emergency services through the Pan-European eCall system can be
cancelled by pressing the SOS button again only before the call connection.
After activation of emergency call in the manual mode (for proper emergency services
and support), the Pan-European eCall system automatically transmits the road
accident data / or data on other accident to the officer of the Public Safety Answering
Point(PSAP) (during emergency call) by pressing the SOS button.
It can be canceled by pressing the button again in 3 seconds. It can’t be canceled
after that.
In case of road accident or other accidents for activation of emergency call in manual
mode it is necessary:
1. Stop the vehicle in accordance with traffic rules to ensure safety to yourself and
other participants of road traffic;
2. Press the SOS button, when pressing the button SOS registration of the device
in the wireless telephonic communication networks is carried out, minimum
data set about vehicle and its location is collected in accordance with of the
technical requirements of the device. After that connection with the officer of the
Pan-European eCall system is made for clearing up reasons (conditions) of the
emergency call.
3. After clearing up reasons of the emergency call, the officer of the Public Safety
Answering Point(PSAP) sends emergency services and completes the emergency
call.
If the emergency call is not carried out in accordance with the procedure, mentioned
above, the emergency call will be considered as erroneous.