start stop button HYUNDAI I20 2023 Owner's Manual

6-17
06
The transmission is fully synchronized
in all forward gears so shifting to
either a higher or a lower gear is easily
accomplished. Depress the clutch pedal
down fully whilst shifting, then release it
slowly.
If your vehicle is equipped with an
ignition lock switch, the engine will not
start when starting the engine without
depressing the brake pedal and clutch
pedal. (if equipped)
The shift lever must be returned to the
neutral position before shifting into
R (Reverse). Push the button located
immediately below the shift knob
and pull the gearshift lever to the left
sufficiently, and then shift into reverse
(R) gear position. Make sure the vehicle
is completely stopped before shifting
into R (Reverse).
Never operate the engine with the
tachometer (rpm) in the red zone. CAUTION

[When downshifting from fifth gear
to fourth gear, caution should be
taken not to inadvertently press the
shift lever sideways in such a manner
that the second gear is engaged.
Such a drastic downshift may cause
the engine speed to increase to the
point that the tachometer will enter
the red-zone. Such overrevving of
the engine and transmission may
possibly cause engine damage.

[Do not downshift more than 2 gears
or downshift the gear when the
engine is running at high speed
(5,000 RPM or higher). Such a
downshifting may damage the
engine, clutch and the transmission.

[During cold weather, shifting may
be difficult until the transmission
lubricant is warmed up. This is
normal and not harmful to the
transmission.

[If you’ve come to a complete stop
and it’s hard to shift into the 1st gear
or R(Reverse), leave the shift lever at
N(Neutral) position and release the
clutch. Press the clutch pedal back
down, and then shift into the 1st gear
or R(Reverse) gear position.

6-33
06
Shift-lock release
If the shift lever cannot be moved from
the P (Park) position into R (Reverse)
position with the brake pedal depressed,
continue depressing the brake, and then
do the following:
OBC3060003R
1. Place the ignition switch in the LOCK/
OFF position.
2. Apply the parking brake.
3. Press the shift-lock release button.
4. Press and hold the lock release button
on the shift lever.
5. Move the shift lever.
If you need to use the shift-lock release,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer immediately.
Ignition key interlock system
(if equipped)
The ignition key cannot be removed
unless the shift lever is in the P (Park)
position.
Parking
Always come to a complete stop and
continue to depress the brake pedal.
Move the shift lever into the P (Park)
position, apply the parking brake, and
place the ignition switch in the LOCK/
OFF position. Take the Key with you
when exiting the vehicle.
WARNING
When you stay in the vehicle with
the engine running, be careful not to
depress the accelerator pedal for a long
period of time. The engine or exhaust
system may overheat and start a fire.
The exhaust gas and the exhaust
system are very hot. Keep away from
the exhaust system components.
Do not stop or park over flammable
materials, such as dry grass, paper or
leaves. They may ignite and cause a
fire.

6-46
Driving your vehicle
Your vehicle may be equipped with
the ISG system, which reduces fuel
consumption by stopping and restarting
the engine automatically.
The engine starts automatically as soon
as the starting conditions are met.
NOTICE
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, EPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean
the system is malfunctioning.
Activating the ISG
Prerequisite for activation
The ISG system operates in the following
situations.

[The driver’s seatbelt is fastened

[The driver’s door and bonnet are
closed

[The brake vacuum pressure is
adequate

[The battery sensor is activated and the
battery is sufficiently charged

[Outside temperature is not too low or
too high

[The vehicle is driven over a constant
speed and stops

[ The climate control system satisfies
the conditions

[The vehicle is sufficiently warmed up

[The incline is gradual

[The steering wheel is turned less than
180 degrees and then the vehicle
stops
Deactivating the ISG
OBC3N061014AU
If you want to deactivate the ISG system,
press the ISG OFF button.
The light on the ISG OFF button will
illuminate.
If you press the ISG OFF button again,
the system will be activated and the light
on the ISG OFF button will turn off.
,'/(6723$1'*2

6-51
06
ISG Indication
The ISG System is indicated by lamp on
the instrument cluster. If your vehicle is
equipped with a supervision cluster, the
notice will illuminate on the LCD display.
OBC3060009
The system may require the engine to
manually restart when the light on the
ISG OFF button will illuminate and if your
vehicle is equipped with a supervision
cluster, a warning message comes on
continuously.
OBC3N061014AU
OBC3070110TU/OBC3070111TU
The engine will not start if the shift lever
is moved from the N (neutral) stage to
the D (driving) stage, manual mode, or R
(reverse) stage without stepping on the
brake pedal whilst the engine is stopped
automatically. At this time, if you press
the brake it will be restarted.

6-52
Driving your vehicle
Conventional MT vehicle (not MHEV or
not equipped with LATE Restart) is able
to restart engine, only in Neutral gear.
If you select a gear, without depressing
clutch pedal fully, then warning will be
displayed with beep. You should restart
the engine in Neutral gear position.
Unintentionally, when the engine is
turned off or the vehicle is moving, if the
gear is engaged and the clutch pedal
is not pressed, the system displays the
warning message as shown below. At
this time, if the driver presses the clutch
pedal all the way, the engine restarts
automatically. (Only with Late Restart
equipped ISG system, except MHEV)
OPDE050564L
ISG malfunction
The system may not operate when:
OBC3060009
The ISG related sensors or system error
occurs.
The yellow AUTO STOP indicator
(
) on the instrument cluster will
stay on after blinking for 5 seconds and
the light on the ISG OFF button will
illuminate.
NOTICE

[ ,IWKH,6*2))EXWWRQOLJKWLVQRW
turned off by pressing the ISG OFF
button again or if the ISG system
continuously does not work correctly,
have your vehicle inspected by a
professional workshop as soon as
possible. Hyundai recommends
to contact a HYUNDAI authorised
repairer.

[ :KHQWKH,6*2))EXWWRQOLJKWFRPHV
on, it may stop illuminating after
driving your vehicle at approximately
50 mph (80 km/h) for a maximum
of two hours and setting the fan
speed control knob below the 2nd
position. If the ISG OFF button light
continues to be illuminated in spite
of the procedure, have your vehicle
inspected by a professional workshop
as soon as possible. Hyundai
recommends to contact a HYUNDAI
authorised repairer.

Driver assistance system
7-32
„Type A
OTM070141L
„Type B
ONX4E070090
Warning volume
With the Engine Start/Stop button in the
ON position, select ‘Driver Assistance

07
7-61
Safe Exit Warning settings
Setting features
OCN7070042L
Safe Exit Warning
With the Engine Start/Stop button in the
21SRVLWLRQVHOHFW
S'ULYHU$VVLVWDQFH

07
7-71
Speed Limit Offset
With the Engine Start/Stop button in the
ON position, when ‘Driver assistance

8-4
Emergency situations
IN CASE OF AN EMERGENCY WHILST DRIVING
If the engine stalls whilst driving

[Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.

[Turn on your hazard warning flasher.

[Try to start the engine again. If your
vehicle will not start, we recommend
that you contact a HYUNDAI
authorised repairer.
If the engine stalls at a
crossroad or crossing
If the engine stalls at a crossroads or
crossing, if safe to do so, move the shift
lever to the N (Neutral) position and then
push the vehicle to a safe location.
If you have a flat tyre whilst
driving
If a tyre goes flat whilst you are driving:

[Take your foot off the accelerator
pedal and let the vehicle slow down
whilst driving straight ahead. Do
not apply the brakes immediately or
attempt to pull off the road as this
may cause loss of vehicle control
resulting in an accident. When the
vehicle has slowed to such a speed
that it is safe to do so, brake carefully
and pull off the road. Drive off the
road as far as possible and park on
firm, level ground. If you are on a
divided highway, do not park in the
median area between the two traffic
lanes.

[When the vehicle is stopped, press
the hazard warning flasher button,
move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.

[Have all passengers get out of the
vehicle. Be sure they all get out on the
side of the vehicle that is away from
traffic.

[When changing a flat tyre, follow
the instructions provided later in this
chapter.

8-12
Emergency situations
Tyre pressure monitoring
system
WARNING
Over-inflation or under-inflation can
reduce tyre life, adversely affect
vehicle handling, and lead to sudden
tyre failure that may cause loss of
vehicle control resulting in an accident.
Each tyre, including the spare (if
provided), should be checked monthly
when cold and inflated to the inflation
pressure recommended by the vehicle
manufacturer on the vehicle placard
or tyre inflation pressure label. (If your
vehicle has tyres of a different size
than the size indicated on the vehicle
placard or tyre inflation pressure label,
you should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a tyre
pressure monitoring system (TPMS)
that illuminates a low tyre pressure
telltale when one or more of your
tyres is significantly under-inflated.
Accordingly, when the low tyre pressure
telltale illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper pressure.
Driving on a significantly under-inflated
tyre causes the tyre to overheat and can
lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and
may affect the vehicle’s handling and
stopping ability.
Please note that the TPMS is not a
substitute for proper tyre maintenance,
and it is the driver’s responsibility to
maintain correct tyre pressure, even if
under-inflation has not reached the level
to trigger illumination of the TPMS low
tyre pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator
to indicate when the system is
not operating properly. The TPMS
malfunction indicator is combined with
the low tyre pressure telltale. When
the system detects a malfunction, the
telltale will flash for approximately one
minute and then remain continuously
illuminated. This sequence will continue
upon subsequent vehicle start-ups as
long as the malfunction exists.
When the malfunction indicator is
illuminated, the system may not be able
to detect or signal low tyre pressure as
intended. TPMS malfunctions may occur
for a variety of reasons, including the
installation of replacement or alternate
tyres or wheels on the vehicle that
prevent the TPMS from functioning
properly.
Always check the TPMS malfunction
telltale after replacing one or more tyres
or wheels on your vehicle to ensure that
the replacement or alternate tyres and
wheels allow the TPMS to continue to
function properly.
NOTICE
If any of the below happens, we
recommend that you have the system
checked by a HYUNDAI authorised
repairer.
1. The Low Tyre Pressure Telltale/
TPMS Malfunction Indicator does not
illuminate for 3 seconds when the
Engine Start/Stop button is pressed
to the ON position or when the
engine is running.
2. The TPMS Malfunction Indicator
remains illuminated after blinking for
approximately 1 minute.
3. The Low Tyre Pressure Position
Telltale remains illuminated.