automatic transmission HYUNDAI I20 2023 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 345 of 649
6-72
Driving your vehicle
Ready to leave after parking on a
hill
1. With the shift lever to P (Park, for
Automatic transmission/Dual clutch
transmission vehicle) or neutral (for
Manual transmission vehicle), apply
your brakes and hold the brake pedal
down whilst you:
V Start your engine;
V Shift into gear; and
V Release the parking brake.
2. Slowly remove your foot from the
brake pedal.
3. Drive slowly until the trailer is clear of
the chocks.
4. Stop and have someone pick up and
store the chocks.
Maintenance when towing a
trailer
Your vehicle will need service more
often when you regularly pull a trailer.
Important items to pay particular
attention to include engine oil,
automatic transmission/dual clutch
transmission fluid, axle lubricant and
cooling system fluid. Brake condition
is another important item to frequently
check. If you’re trailering, it’s a good
idea to review these items before
you start your trip. Don’t forget to
also maintain your trailer and towbar.
Follow the maintenance schedule that
accompanied your trailer and check it
periodically. Preferably, conduct the
check at the start of each day’s driving.
Most importantly, all towbar nuts and
bolts should be tight.
NOTICE
To prevent vehicle damage:
V Due to higher load during trailer
usage, overheating might occur on
hot days or during uphill driving. If
the coolant gauge indicates over-
heating, switch off the air conditioner
and stop the vehicle in a safe area to
cool down the engine.
V When towing check Automatic
transmission/Dual clutch
transmission fluid more frequently.
V If your vehicle is not equipped with
an air conditioner, you should install
a condenser fan to improve engine
performance when towing a trailer.
Page 519 of 649
8-4
Emergency situations
IN CASE OF AN EMERGENCY WHILST DRIVING
If the engine stalls whilst driving
[ Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.
[ Turn on your hazard warning flasher.
[ Try to start the engine again. If your
vehicle will not start, we recommend
that you contact a HYUNDAI
authorised repairer.
If the engine stalls at a
crossroad or crossing
If the engine stalls at a crossroads or
crossing, if safe to do so, move the shift
lever to the N (Neutral) position and then
push the vehicle to a safe location.
If you have a flat tyre whilst
driving
If a tyre goes flat whilst you are driving:
[ Take your foot off the accelerator
pedal and let the vehicle slow down
whilst driving straight ahead. Do
not apply the brakes immediately or
attempt to pull off the road as this
may cause loss of vehicle control
resulting in an accident. When the
vehicle has slowed to such a speed
that it is safe to do so, brake carefully
and pull off the road. Drive off the
road as far as possible and park on
firm, level ground. If you are on a
divided highway, do not park in the
median area between the two traffic
lanes.
[ When the vehicle is stopped, press
the hazard warning flasher button,
move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
[ Have all passengers get out of the
vehicle. Be sure they all get out on the
side of the vehicle that is away from
traffic.
[ When changing a flat tyre, follow
the instructions provided later in this
chapter.
Page 520 of 649
8-5
08
If the engine doesn’t turn over
or turns over slowly
[ Be sure the shift lever is in N (Neutral)
or P (Park) if it is an automatic
transmission/dual clutch transmission
vehicle. The engine starts only when
the shift lever is in N (Neutral) or P
(Park).
[ Check the battery connections to be
sure they are clean and tight.
[ Turn on the interior light. If the light
dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to start
it. This could cause damage to your
vehicle. See instructions for “Jump
Starting” provided in this chapter.
CAUTION
Push or pull starting the vehicle may
cause the catalytic converter to
overload which can lead to damage to
the emission control system.
If the engine turns over normally
but doesn’t start
[ Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call a HYUNDAI
authorised repairer for assistance.
IF THE ENGINE WILL NOT START
Page 522 of 649
8-7
08
i Information
Pb
An inappropriately disposed
battery can be harmful to the
environment and human
health. Dispose of the battery
according to your local law(s)
or regulations.
Jump starting procedure
1. Position the vehicles close enough
that the jumper cables will reach, but
do not allow the vehicles to touch.
2. Avoid fans or any moving parts in the
engine compartment at all times, even
when the vehicles are turned off.
3. Turn off all electrical devices such
as radios, lights, air conditioning,
etc. Put the vehicles in P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral (for
manual transmission vehicle), and set
the parking brakes. Turn both vehicles
OFF.1VQA4001
4. Connect the jumper cables in
the exact sequence shown in the
illustration. First connect one jumper
cable to the red, positive (+) jumper
terminal of your vehicle (1).
5. Connect the other end of the jumper
cable to the red, positive (+) battery/
jumper terminal of the assisting
vehicle (2).
6. Connect the second jumper cable to
the black, negative (-) battery/ chassis
ground of the assisting vehicle (3).
7. Connect the other end of the second
jumper cable to the black, negative (-)
chassis ground of your vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over the
battery when making connections.
8. Start the engine of the assisting
vehicle and let it run at approximately
2,000rpm for a few minutes. Then
start your vehicle.
If your vehicle will not start after a
few attempts, it probably requires
servicing. In this event, please seek
qualified assistance. If the cause of your
battery discharging is not apparent, we
recommend that you have your vehicle
checked by a HYUNDAI authorised
repairer.
Page 524 of 649
8-9
08
If your temperature gauge indicates
overheating, you experience a loss of
power, or hear loud pinging or knocking,
the engine may be overheating. If this
happens, you should:
1. Pull off the road and stop as soon as it
is safe to do so.
2. Place the shift lever in P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral (for
manual transmission/dual clutch
transmission vehicle) and set the
parking brake. If the air conditioning is
ON, turn it OFF.
3. If engine coolant is running out under
the vehicle or steam is coming out
from the bonnet, stop the engine. Do
not open the bonnet until the coolant
has stopped running or the steaming
has stopped. If there is no visible
loss of engine coolant and no steam,
leave the engine running and check
to be sure the engine cooling fan is
operating. If the fan is not running,
turn the engine off.
WARNING
Whilst the engine is
running, keep hands,
clothing and tools away
from the moving parts such
as the cooling fan and drive
belt to prevent serious
injury.4. Check for coolant leaking from the
radiator, hoses or under the vehicle. (If
the air conditioning had been in use, it
is normal for cold water to be draining
from it when you stop.)
5. If engine coolant is leaking out, stop
the engine immediately and we
recommend that you call a HYUNDAI
authorised repairer for assistance.
WARNING
NEVER remove the radiator
cap or the drain plug whilst
the engine and radiator are
hot. Hot coolant and steam
may blow out under
pressure, causing serious injury.
Turn the engine off and wait until the
engine cools down. Use extreme care
when removing the radiator cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back whilst the pressure
is released from the cooling system.
When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove it.
IF THE ENGINE OVERHEATS
Page 532 of 649
8-17
08
Changing tyres
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:
[ Do not get under a vehicle that is
supported by a jack.
[ NEVER attempt to change a tyre in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tyre. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.
[ Be sure to use the jack provided with
the vehicle.
[ ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.
[ Do not start or run the engine whilst
the vehicle is on the jack.
[ Do not allow anyone to remain in the
vehicle whilst it is on the jack.
[ Keep children away from the road
and the vehicle.
Follow these steps to change your
vehicle’s tyre:
1. Park on a level, firm surface.
2. Move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tyre from
the vehicle.
OBC3080005
[A] : Block
5. Block both the front and rear of the
tyre diagonally opposite of the tyre
you are changing.
OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tyre has
been raised off of the ground.
Page 536 of 649
8-21
08
Jack label
OHYK065011/OAC3N070038TU
„Type A
„Type B
The actual Jack label in the vehicle may differ from the illustration.
For more detailed specifications, refer to the label attached to the jack.
1. Model Name
2. Maximum allowable load
3. When using the jack, set your parking brake.
4. When using the jack, stop the engine.
5. Do not get under a vehicle that is supported by a jack.
6. The designated locations under the frame
7. When supporting the vehicle, the base plate of jack must be vertical under the
lifting point.
8. Shift into Reverse gear on vehicles with manual transmission or move the shift lever
to the P position on vehicles with automatic transmission/dual clutch transmission.
9. The jack should be used on firm level ground.
10. Jack manufacture
11. Production date
12. Representative company and address
Page 550 of 649
8-35
08
OBC3080021
[ Use a towing cable or chain less than 5
m (16 feet) long. Attach a white or red
cloth (about 30cm (12 inches) in width)
in the middle of the cable or chain for
easy visibility.
[ Drive carefully so the towing cable or
chain remains tight during towing.
[ Before towing, check the automatic
transmission/dual clutch transmission
for fluid leaks under your vehicle.
If the automatic transmission fluid is
leaking, flatbed equipment or a towing
dolly must be used.
NOTICE
Accelerate or decelerate the vehicle
in a slow and gradual manner whilst
maintaining tension on the tow rope
or chain to start or drive the vehicle,
otherwise tow hooks and the vehicle
may be damaged.
NOTICE
To avoid damage to your vehicle and
vehicle components when towing:
[ $ O Z D \ V S X O O V W U D L J K W D K H D G Z K H Q
using the towing hooks. Do not pull
from the side or at a vertical angle.
[ ' R Q R W X V H W K H W R Z L Q J K R R N V W R S X O O
a vehicle out of mud, sand or other
conditions from which the vehicle
cannot be driven out under its own
power.
[ / L P L W W K H Y H K L F O H V S H H G W R P S K
(15 km/h) and drive less than 1
mile (1.5 km) when towing to avoid
serious damage to transmission. (for
Automatic transmission/Dual clutch
transmission)
[ 7 K H Y H K L F O H V K R X O G E H W R Z H G D W D
speed of 15 mph (25 km/h) or less
within the distance of 12 miles (20
km). (for Manual transmission/
Intelligent manual transmission)
Page 557 of 649
8-42
Emergency situations
Automatic accident reporting
OBC3080024
System operation in the event of a traffic accidentConnection with the Public Safety Answering Point(PSAP)
Emergency services
The Pan-European eCall device automatically makes an emergency call to the Public
Safety Answering Point (PSAP) for proper rescuing operations in the event of vehicle
accident.
For proper emergency services and support, the Pan-European eCall system
automatically transmits the accident data to the Public Safety Answering Point (PSAP)
when a traffic accident is detected.
In this case, the emergency call cannot be hung up by pressing the SOS button and
the Pan-European eCall system remains connected until the emergency service
officer, receiving the call, disconnects the emergency call.
In minor traffic accidents, the Pan-European eCall system may not execute an
emergency call. However, an emergency call may be made manually by pressing the
SOS button.
CAUTION
Operation of the system is impossible in case of absence of mobile transmission
and GPS and Galileo signals.
Page 566 of 649
9-7
09
WARNING
Performing maintenance work on a
vehicle can be dangerous. If you lack
sufficient knowledge and experience
or the proper tools and equipment
to do the work, we recommend that
the system be serviced by a HYUNDAI
authorised repairer. ALWAYS follow
these precautions for performing
maintenance work:
[ 3 D U N \ R X U Y H K L F O H R Q O H Y H O J U R X Q G
move the shift lever into the P (Park,
for automatic transmission/dual
clutch transmission vehicle) position,
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
[ % O R F N W K H W \ U H V I U R Q W D Q G E D F N W R
prevent the vehicle from moving.
Remove loose clothing or jewellery
that can become entangled in
moving parts.
[ , I \ R X P X V W U X Q W K H H Q J L Q H G X U L Q J
maintenance, do so out doors or in an
area with plenty of ventilation.
[ . H H S I O D P H V V S D U N V R U V P R N L Q J
materials away from the battery and
fuel-related parts.The following lists are vehicle checks
and inspections that should be
performed by the owner or a HYUNDAI
authorised repairer at the frequencies
indicated to help ensure safe,
dependable operation of your vehicle.
Any adverse conditions should be
brought to the attention of your dealer
as soon as possible.
These Owner Maintenance vehicle
checks are generally not covered by
warranties and you may be charged for
labour, parts and lubricants used.
Owner maintenance schedule
When you stop for fuel:
[ Check the coolant level in the engine
coolant reservoir.
[ Check the windscreen washer fluid
level.
[ Check for low or under-inflated tyres.
[ Check the radiator and condenser.
Check if the front of the radiator and
condenser are clean and not blocked
with leaves, dirt or insects, etc.
If any of the above parts are extremely
dirty or you are not sure of their
condition, we recommend that
you contact a HYUNDAI authorised
repairer.
WARNING
% H F D U H I X O Z K H Q F K H F N L Q J \ R X U H Q J L Q H
coolant level when the engine is hot.
This may result in coolant being blown
out of the opening and cause serious
burns and other injuries.
OWNER MAINTENANCE