display HYUNDAI I20 2023 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 167 of 649
5-26
Convenient features
Folding the outside rearview mirror
OAI3059020
0 D Q X D O W \ S H L I H T X L S S H G
To fold the outside rearview mirror,
grasp the housing of the mirror and the
fold it toward the rear of the vehicle.
OBC3050016R
Electric type (if equipped)
The outside rearview mirror can be
folded or unfolded by pressing the
switch. When vehicle speed is over 9.3
mph (15 km/h), the outside rearview
mirror will not fold even though the
switch is pressed.
However, the outside rearview mirror
will unfold when the switch is pressed.
[ If 'Convenience J Welcome mirror
JOn door unlock' is selected in
the User Settings mode on the LCD
display, the User Settings mode on the
LCD display, the outside mirror will
fold or unfold automatically as follows:
- The mirror will fold or unfold when
the door is locked or unlocked by the
smart key.
- The mirror will fold or unfold when
the door is locked or unlocked by the
button on the outside door handle.
[ If 'Convenience J Welcome mirror
JOn door unlock' and 'Convenience
J Welcome mirror J On driver
approach' is selected in the User
Settings mode.
If your vehicle is equipped with
additional navigation, please refer
to the infotainment system manual
separately supplied.
NOTICE
The electric type outside rearview
mirror operates even though the
L J Q L W L R Q V Z L W F K L V L Q W K H 2 ) ) S R V L W L R Q
However, to prevent unnecessary
battery discharge, do not adjust the
mirrors longer than necessary whilst
the engine is not running.
NOTICE
Do not fold the electric type outside
rearview mirror by hand. It could cause
motor failure.
Page 176 of 649
5-35
05
Sunroof open warning
OCN7040018
If the driver turns off the engine when
the sunroof is not fully closed, the
warning chime will sound for several
seconds and the sunroof open warning
will appear on the cluster LCD display.
Close the sunroof securely when leaving
your vehicle.
CAUTION
Make sure the sunroof is closed fully
when leaving your vehicle.
If the sunroof is left open, rain or snow
may wet the interior of the vehicle.
Also, leaving the sunroof open when
the vehicle is unattended may invite
theft.
Page 178 of 649
5-37
05
Closing the bonnet
1. Before closing the bonnet, check the
following:
[ $ O O I L O O H U F D S V L Q H Q J L Q H F R P S D U W P H Q W
must be correctly installed.
[ * O R Y H V U D J V R U D Q \ R W K H U
combustible materials must
be removed from the engine
compartment.
2. Return the support rod to its clip
location for preventing it from rattling.
3. Lower the bonnet halfway (lifted
approximately 30cm from the closed
position) and push down to securely
lock in place. Then double check to be
sure the bonnet is secure.
If the bonnet can be raised slightly, it
is not securely locked. Open it again
and close it with more force.
WARNING
[ Before closing the bonnet, ensure
all obstructions are removed from
around the bonnet opening.
[ Always double check to be sure
that the bonnet is firmly latched
before driving away. Check there
is no bonnet open warning light or
message displayed on the instrument
cluster. Driving with the bonnet
opened may cause a total loss of
visibility, which might result in an
accident.
[ Do not move the vehicle with the
bonnet in the raised position, as
vision is obstructed, which might
result in an accident, and the bonnet
could fall or be damaged.
Tailgate
Opening the tailgate
OBC3050025
[ 7 K H W D L O J D W H L V O R F N H G R U X Q O R F N H G
when all doors are locked or unlocked
with the remote key, smart key or
central door lock/unlock switch.
[ , I X Q O R F N H G W K H W D L O J D W H F D Q E H
opened by pulling up the tailgate
outside handle.
i Information
, Q F R O G D Q G Z H W F O L P D W H V G R R U O R F N D Q G
door mechanisms may not work properly
G X H W R I U H H ] L Q J F R Q G L W L R Q V
WARNING
The tailgate swings upward. Make
sure no objects or people are near the
rear of the vehicle when opening the
tailgate.
Page 185 of 649
5-44
Convenient features
OAE046455L
To flash the high beam headlight, pull
the lever towards you, then release the
lever. The high beams will remain ON as
long as you hold the lever towards you.
Turn signals and lane change
signals
OTLE045284
To signal a turn, push down on the lever
for a left turn or up for a right turn in
position (A). To signal a lane change,
move the turn signal lever slightly and
hold it in position (B).
The lever will return to the OFF position
when released or when the turn is
completed.
If an indicator stays on and does not
flash or if it flashes abnormally, one of
the turn signal bulbs may be burned out
and will require replacement.
2 Q H W R X F K W X U Q V L J Q D O I X Q F W L R Q
To activate a one-touch turn signal
function, move the turn signal lever
slightly and then release it. The lane
change signals will blink 3, 5 or 7 times.
You can activate or deactivate the One
Touch Turn Signal function or choose
the number of blinks (3, 5, or 7) from the
User Settings Mode on the LCD display.
) R U P R U H G H W D L O V U H I H U W R U / & ' ' L V S O D \
0 R G H VV L Q F K D S W H U
Page 197 of 649
5-56
Convenient features
CAUTION
[ To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
[ To prevent possible damage to the
wipers or windscreen, do not operate
the wipers when the windscreen is
dry.
[ To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
[ To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
Rear window wiper and washer
switch (if equipped)
OTLE045167
The rear window wiper and washer
switch is located at the end of the wiper
and washer switch lever.
Turn the switch to desired position to
operate the rear wiper and washer.
· 2 – High wiper speed
· 1 – Low wiper speed
· O – Off
OTLE045167
Push the lever away from you to spray
rear washer fluid and to run the rear
wipers 1~3 cycles. The spray and wiper
operation will continue until you release
the lever. (if equipped)
Auto rear wiper (if equipped)
The rear wiper will operate whilst the
vehicle is in reverse with the front wiper
ON by selecting the function on the LCD
display.
* R W R S 8 V H U 6 H W W L Q J V
Page 211 of 649
5-70
Convenient features
Temperature control
OBC3050111R
The temperature will increase by
pushing the switch to up.
The temperature will decrease by
pushing the switch to down.
The temperature will increase or
decrease by 0.5°C (1°F) for each
incremental location. When set to the
lowest temperature setting, the air
conditioning will operate continuously.
7 H P S H U D W X U H F R Q Y H U V L R Q
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from °C
to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 seconds
whilst pressing the OFF button.
- Instrument cluster
Go to User Settings o Units o
Temperature Unit.
The temperature unit on both the cluster
LCD display and the climate control
screen will change.
Air intake control
OBC3050114R
This is used to select the outside (fresh)
air position or recirculated air position.
To change the air intake control position,
push the control button.
5 H F L U F X O D W H G D L U S R V L W L R Q
With the recirculated air
position selected, air from
the passenger
compartment will be
drawn through the heating
system and heated or
cooled according to the
function selected.
2 X W V L G H I U H V K D L U S R V L W L R Q
With the outside (fresh) air
position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.
Page 228 of 649
5-87
05
USB charger (if equipped)
OBC3N051027AU
The USB charger is located inside the
F R Q V R O H E R [ E H W Z H H Q W K H G U L Y H UT V V H D W
D Q G W K H I U R Q W S D V V H Q J H UT V V H D W , Q V H U W
the USB charger into the USB port, and
re-charge a smart phone or a tablet PC.
[ $ F K D U J L Q J V W D W X V F K D U J L Q J F R P S O H W L R Q
message is displayed on a screen of a
smart phone or a tablet PC.
[ $ V P D U W S K R Q H R U D W D E O H W 3 & P D \
get warmer during the re-charging
process. It does not indicate any
malfunction with the charging system.
[ $ V P D U W S K R Q H R U D W D E O H W 3 & Z K L F K
adopts a different re-charging
method, may not be properly
re-charged. In this case, use an
exclusive charger of your device.
[ 7 K H F K D U J L Q J W H U P L Q D O L V R Q O \ W R
re-charge a device. Do not use the
charging terminal either to turn ON an
audio or to play media on the AVN.
Wireless mobile phone charging
system (if equipped)
OBC3N050028
[A] : Charging pad
There is a wireless mobile phone charger
inside the front console.
The system is available when all doors
are closed, and when the ignition switch
is in the ON position.
Page 229 of 649
5-88
Convenient features
To charge a mobile phone
The wireless mobile phone charging
system charges only the Qi-enabled
mobile phones (
). Read the label on
the mobile phone accessory cover or
Y L V L W \ R X U P R E L O H S K R Q H P D Q X I D F W X U H UT V
website to check whether your mobile
phone supports the Qi technology.
The wireless charging process starts
when you put a Qi-enabled mobile
phone on the wireless charging unit.
1. Remove other items, including the
smart key, from the wireless charging
unit. If not, the wireless charging
process may be interrupted. Place
the mobile phone on the centre of
charging pad.
2. The indicator light is orange when
the mobile phone is charging. The
indicator light turns green when phone
charging is complete.
3. You can turn ON or OFF the wireless
charging function in the User Settings
mode on the instrument cluster. For
further information, refer to the “LCD
Display Modes” in this chapter 4.
If your mobile phone is not charging:
- Slightly change the position of the
mobile phone on the charging pad.
- Make sure the indicator light is orange.
The indicator light will blink orange for
10 seconds if there is a malfunction in
the wireless charging system.
In this case, temporarily stop the
charging process, and re-attempt to
wirelessly charge your mobile phone.
The system warns you with a message
on the LCD display if the mobile phone
is still on the wireless charging unit after
the engine is turned OFF and the front
door is opened.
) R U V R P H P D Q X I D F W X U H U VT P R E L O H S K R Q H V
the system may not warn you even
though the mobile phone is left on the
wireless charging unit. This is due to the
particular characteristic of the mobile
phone and not a malfunction of the
wireless charging.
Page 244 of 649
![HYUNDAI I20 2023 Owners Guide 5-103
05
❈ The system’s actual appearance and layout may differ depending on the vehicle
model and specification.
„Type B
: L W K Bluetooth p : L U H O H V V 7 H F K Q R O R J \](/img/35/56129/w960_56129-243.png "HYUNDAI I20 2023 Owners Guide 5-103
05
❈ The system’s actual appearance and layout may differ depending on the vehicle
model and specification.
„Type B
: L W K Bluetooth p : L U H O H V V 7 H F K Q R O R J \")
5-103
05
❈ The system’s actual appearance and layout may differ depending on the vehicle
model and specification.
„Type B
: L W K Bluetooth p : L U H O H V V 7 H F K Q R O R J \
(1) 6 ( ( . 7 5 $ & . E X W W R Q
[ Change the station/track/file.
[ Whilst listening to the radio, press
and hold to search for a station.
[ Whilst playing media, press and hold
to rewind or fast forward (except for
the Bluetooth audio mode).
(2) 0 ( 1 8 E X W W R Q & / 2 & . E X W W R Q
[ Press to access the menu screen for
the current mode.
[ Press and hold to access the time
setup screen.
(3) 7 8 1 ( N Q R E ) , / ( N Q R E ( 1 7 ( 5
E X W W R Q
[ Whilst listening to the radio, turn to
adjust the frequency.
[ Whilst playing media, turn to search
for a track/file (except for the
Bluetooth audio mode).
[ Whilst searching by turning the
knob, press to select the current
track/file (except for the Bluetooth
audio mode).(4) $ 8 ' , 2 E X W W R Q
[ Press to display the radio/media
mode selection window.
[ When the mode selection window
displays, turn the [ 7 8 1 (] knob to
select the desired mode and then
press the knob.
[ When the Mode popup is not
selected in [ 0 ( 1 8 & / 2 & .] X 0 R G H
S R S X S, press the [AUDIO] button
on the control panel to change the
mode. Each time you press the
[AUDIO] button on the control panel,
the mode switches to radio X media
in order.
Page 249 of 649
5-108
Convenient features
7 X U Q L Q J W K H G L V S O D \ R Q R U R I I
To prevent glare, you can turn off the
screen. The screen can be turned off
only whilst the system is on.
1. On the control panel, press the
[ 0 ( 1 8 & / 2 & .] button.
2. When the option selection window
displays, turn the [ 7 8 1 (] knob to
select ' L V S O D \ R I I, and then press the
knob.
[ To turn the screen back on, press
any of the control panel buttons.
* H W W L Q J W R N Q R Z W K H E D V L F
R S H U D W L R Q V
You can select an item or adjust the
settings by using the number buttons
and the [ 7 8 1 (] knob on the control
panel.
Selecting an item
1 X P E H U H G L W H P V
Press the corresponding number button.
1 X P E H U O H V V L W H P V
Turn the [ 7 8 1 (] knob to select the
desired item, and then press the knob.
Adjusting the settings
Turn the [ 7 8 1 (] knob to adjust the
value, and then press the knob to save
changes.
Turn the [ 7 8 1 (] knob to the right to
increase the value and turn the [ 7 8 1 (]
knob to the left to decrease the value.
❈ The system’s actual appearance and layout may differ depending on the vehicle
model and specification.