stop start HYUNDAI I20 2023 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 297 of 649
6-24
Driving your vehicle
Ignition key interlock system
(if equipped)
The ignition key cannot be removed
unless the shift lever is in the P (Park)
position.
3 D U N L Q J
Always come to a complete stop and
continue to depress the brake pedal.
Move the shift lever into the P (Park)
position, apply the parking brake, and
place the ignition switch in the LOCK/
OFF position. Take the Key with you
when exiting the vehicle.
WARNING
When you stay in the vehicle with
the engine running, be careful not to
depress the accelerator pedal for a long
period of time. The engine or exhaust
system may overheat and start a fire.
The exhaust gas and the exhaust
system are very hot. Keep away from
the exhaust system components.
Do not stop or park over flammable
materials, such as dry grass, paper or
leaves. They may ignite and cause a
fire.
Good driving practices
[ Never move the shift lever from P
(Park) or N (Neutral) to any other
position with the accelerator pedal
depressed.
[ Never move the shift lever into P
(Park) when the vehicle is in motion.
[ Be sure the vehicle is completely
stopped before you attempt to shift
into R (Reverse) or D (Drive).
[ Do not move the shift lever to N
(Neutral) when driving. Doing so may
result in an accident because of a loss
of engine braking and the transmission
could be damaged.
[ Driving uphill or downhill, always shift
to D (Drive) when driving forward or to
R (Reverse) when driving backwards,
and check the gear position indicated
on the cluster before driving. If you
drive in the opposite direction of the
selected gear, the engine will turn
off and a serious accident might be
occurred due to the degraded brake
performance.
[ Do not drive with your foot resting
on the brake pedal. Even light, but
consistent pedal pressure can result
in the brakes overheating, brake wear
and possibly even brake failure.
[ When driving in manual shift mode,
slow down before shifting to a lower
gear. Otherwise, the lower gear may
not be engaged if the engine rpms are
outside of the allowable range.
[ Always apply the parking brake when
leaving the vehicle. Do not depend on
placing the transmission in P (Park) to
keep the vehicle from moving.
[ Exercise extreme caution when driving
on a slippery surface. Be especially
careful when braking, accelerating or
shifting gears. On a slippery surface,
an abrupt change in vehicle speed can
cause the drive wheels to lose traction
and may cause loss of vehicle control
resulting in an accident.
Page 303 of 649
6-30
Driving your vehicle
Transmission ranges
The indicator in the instrument cluster
displays the shift lever position when the
ignition switch is in the ON position.
3 3 D U N
Always come to a complete stop before
shifting into P (Park).
To shift from P (Park), you must depress
firmly on the brake pedal and make sure
your foot is off the accelerator pedal.
If you have done all of the above and
still cannot shift the lever out of P
(Park), see “Shift-Lock Release” in this
chapter.
The shift lever must be in P (Park) before
turning the engine off.
WARNING
[ Shifting into P (Park) whilst the
vehicle is in motion may cause you to
lose control of the vehicle.
[ After the vehicle has stopped, always
make sure the shift lever is in P (Park),
apply the parking brake, and turn the
engine off.
[ When parking on an incline, place the
shift lever in P (Park) and apply the
parking brake to prevent the vehicle
from rolling downhill.
[ For safety, always engage the parking
brake with the shift lever in the P
(Park) position except for the case of
emergency parking.
5 5 H Y H U V H
Use this position to drive the vehicle
backward.
NOTICE
Always come to a complete stop before
shifting into or out of R (Reverse); you
may damage the transmission if you
shift into R (Reverse) whilst the vehicle
is in motion.
1 1 H X W U D O
The wheels and transmission are not
engaged.
Use N (Neutral) if you need to restart
a stalled engine, or if it is necessary to
stop with the engine ON. Shift into P
(Park) if you need to leave your vehicle
for any reason.
Always depress the brake pedal when
you are shifting from N (Neutral) to
another gear.
' ' U L Y H
This is the normal driving position. The
transmission will automatically shift
through a 7-gear sequence, providing
the best fuel economy and power.
For extra power when passing another
vehicle or driving uphill, depress the
accelerator fully. The transmission will
automatically downshift to the next
lower gear (or gears, as appropriate).
Page 306 of 649
6-33
06
Shift-lock release
If the shift lever cannot be moved from
the P (Park) position into R (Reverse)
position with the brake pedal depressed,
continue depressing the brake, and then
do the following:
OBC3060003R
1. Place the ignition switch in the LOCK/
OFF position.
2. Apply the parking brake.
3. Press the shift-lock release button.
4. Press and hold the lock release button
on the shift lever.
5. Move the shift lever.
If you need to use the shift-lock release,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer immediately.
Ignition key interlock system
(if equipped)
The ignition key cannot be removed
unless the shift lever is in the P (Park)
position.
Parking
Always come to a complete stop and
continue to depress the brake pedal.
Move the shift lever into the P (Park)
position, apply the parking brake, and
place the ignition switch in the LOCK/
OFF position. Take the Key with you
when exiting the vehicle.
WARNING
When you stay in the vehicle with
the engine running, be careful not to
depress the accelerator pedal for a long
period of time. The engine or exhaust
system may overheat and start a fire.
The exhaust gas and the exhaust
system are very hot. Keep away from
the exhaust system components.
Do not stop or park over flammable
materials, such as dry grass, paper or
leaves. They may ignite and cause a
fire.
Page 311 of 649
6-38
Driving your vehicle
Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
do not attempt to modulate your brake
pressure and do not try to pump your
brakes. Depress your brake pedal as
hard as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your ABS is active.
ABS does not reduce the time or
distance it takes to stop the vehicle.
Always maintain a safe distance from the
vehicle in front of you.
ABS will not prevent a skid that results
from sudden changes in direction, such
as trying to take a corner too fast or
making a sudden lane change. Always
drive at a safe speed for the road and
weather conditions.
ABS cannot prevent a loss of stability.
Always steer moderately when braking
hard. Severe or sharp steering wheel
movement can still cause your vehicle
to veer into oncoming traffic or off the
road.
On loose or uneven road surfaces,
operation of the anti-lock brake system
may result in a longer stopping distance
than for vehicles equipped with a
conventional brake system.
The ABS warning light (
) will stay
on for several seconds after the ignition
switch is in the ON position. During
that time, the ABS will go through self-
diagnosis and the light will go off if
everything is normal. If the light stays
on, you may have a problem with your
ABS. We recommend that you contact a
HYUNDAI authorised repairer as soon as
possible.
WARNING
If the ABS warning light () is on and
stays on, you may have a problem with
the ABS. Your power brakes will work
normally. To reduce the risk of serious
injury or death, we recommend that
you contact your HYUNDAI dealer as
soon as possible.
NOTICE
When you drive on a road having poor
traction, such as an icy road, and apply
your brakes continuously, the ABS will
be active continuously and the ABS
warning light (
) may illuminate. Pull
your vehicle over to a safe place and
turn the engine off.
Restart the engine. If the ABS warning
light is off, then your ABS system is
normal.
Otherwise, you may have a problem
with your ABS system. We recommend
that you contact a HYUNDAI authorised
repairer as soon as possible.
i Information
: K H Q \ R X M X P S V W D U W \ R X U Y H K L F O H
E H F D X V H R I D G U D L Q H G E D W W H U \ W K H $ % 6
Z D U Q L Q J O L J K W
P D \ W X U Q R Q D W W K H
V D P H W L P H 7 K L V K D S S H Q V E H F D X V H R I W K H
O R Z E D W W H U \ Y R O W D J H , W G R H V Q R W P H D Q \ R X U
$ % 6 L V P D O I X Q F W L R Q L Q J + D Y H W K H E D W W H U \
U H F K D U J H G E H I R U H G U L Y L Q J W K H Y H K L F O H
Page 316 of 649
6-43
06
Hill-Start Assist Control (HAC)
(if equipped)
The Hill-Start Assist Control (HAC)
helps prevent the vehicle from rolling
backwards when starting a vehicle from
a stop on a hill. The system operates the
brakes automatically for approximately
2 seconds and releases the brake after 2
seconds or when the accelerator pedal is
depressed.
WARNING
Always be ready to depress the
accelerator pedal when starting off on
an incline. The HAC activates only for
approximately 2 seconds.
i Information
Page 319 of 649
6-46
Driving your vehicle
Your vehicle may be equipped with
the ISG system, which reduces fuel
consumption by stopping and restarting
the engine automatically.
The engine starts automatically as soon
as the starting conditions are met.
NOTICE
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, EPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean
the system is malfunctioning.
Activating the ISG
Prerequisite for activation
The ISG system operates in the following
situations.
[ The driver’s seatbelt is fastened
[ The driver’s door and bonnet are
closed
[ The brake vacuum pressure is
adequate
[ The battery sensor is activated and the
battery is sufficiently charged
[ Outside temperature is not too low or
too high
[ The vehicle is driven over a constant
speed and stops
[ The climate control system satisfies
the conditions
[ The vehicle is sufficiently warmed up
[ The incline is gradual
[ The steering wheel is turned less than
180 degrees and then the vehicle
stops
Deactivating the ISG
OBC3N061014AU
If you want to deactivate the ISG system,
press the ISG OFF button.
The light on the ISG OFF button will
illuminate.
If you press the ISG OFF button again,
the system will be activated and the light
on the ISG OFF button will turn off.
, ' / ( 6 7 2 3 $ 1 ' * 2
Page 321 of 649
6-48
Driving your vehicle
Automatic Transmission/Dual Clutch
Transmission
- Conventional Idle STOP
[ ' H F U H D V H W K H Y H K L F O H V S H H G W R P S K
(0 km/h).
[ 3 U H V V W K H E U D N H S H G D O
- Extended Idle STOP
[ ' H F U H D V H W K H Y H K L F O H V S H H G O H V V W K D Q
15 mph (25 km/h).
[ 3 U H V V W K H E U D N H S H G D O
- During Sailing Mode
You can keep engine off status from
sailing to standstill by pressing brake
pedal below 24 mph (40 km/h).
NOTICE
Vehicle which is equipped automatic
transmission or dual clutch
transmission must reach a speed of at
least 18 mph (30 km/h) for Extended
Idle STOP or 3 mph (5 km/h) for
Conventional Idle STOP since last idle
stop.
- If you unfasten the seat belt or open
the driver’s door (engine bonnet)
in auto stop mode at standstill, ISG
system will be deactivated.
Auto start
To restart the engine from idle stop
mode (except 48V MHEV)
Manual transmission vehicle/ Intelligent
Manual Transmission
Vehicle which is equipped with manual
transmission or intelligent manual
transmission is available two version of
restart.
- Conventional restart
Press the clutch pedal when the shift
lever is in the N (Neutral) position.
- Late restart (if equipped)
1. Depress the clutch pedal
2. Engage the gear
3. Release the brake pedal
NOTICE
1. Late restart function is only operated
when it is on a level ground and the
vehicle is stable.
2. To start the engine when the brake
pedal is not pressed or gear is already
engaged, press the brake pedal first
and press on the clutch pedal for
safety.
3. To turn on the engine without vehicle
movement with the brake pedal
pressed (only with Late Restart),
[ 3 U H V V D Q G U H O H D V H W K H F O X W F K S H G D O
[ 3 U H V V W K H F O X W F K S H G D O D J D L Q
immediately
4. After the engine stall, If you operate
as below the engine will start.
[ 5 H O H D V H W K H F O X W F K S H G D O D I W H U W K H
engine completely stop
[ ' H S U H V V W K H F O X W F K S H G D O
Page 322 of 649
6-49
06
Automatic Transmission/Dual Clutch
Transmission
- Release the brake pedal.
The engine will start and the green AUTO
STOP indicator (
) on the instrument
cluster will go out.
7 R U H V W D U W W K H H Q J L Q H I U R P L G O H V W R S
P R G H I R U 9 0 + ( 9
Manual Transmission/Intelligent
Manual Transmission
- Before standstill
Press the clutch pedal if the clutch pedal
has not pressed.
If the clutch pedal has already been
pressed, release the brake pedal or
move the gear to a position other than N
position.
- After standstill
[ , I W K H F O X W F K S H G D O K D V D O U H D G \ E H H Q
pressed, release the brake pedal or
move the gear from N (Neutral).
[ , I W K H F O X W F K S H G D O L V Q R W S U H V V H G W K H
engine will restart in accordance with
the LATE Restart procedure.
1) Depress the clutch pedal
2) Engage the gear
3) Release only the brake pedal
NOTICE
1. Late restart function is only operated
when it is on a level ground and the
vehicle is stable.
2. To start the engine when the brake
pedal is not pressed or gear is already
engaged, press the brake pedal first
and press on the clutch pedal for
safety.
3. To turn on the engine without vehicle
movement with the brake pedal
pressed (only with Late Restart),
[ 3 U H V V D Q G U H O H D V H W K H F O X W F K S H G D O
[ 3 U H V V W K H F O X W F K S H G D O D J D L Q
immediately
4. After the engine stall, if you operate
as below the engine will start.
[ 5 H O H D V H W K H F O X W F K S H G D O D I W H U W K H
engine completely stops
[ ' H S U H V V W K H F O X W F K S H G D O
5. After operating ISG STOP, if the
vehicle speed increases instead of
decreasing, the engine may restart
automatically.
Automatic Transmission/Dual Clutch
Transmission
Release the brake pedal
NOTICE
After operating ISG STOP, if the vehicle
speed increases instead of decreasing,
the engine may restart automatically.
Page 324 of 649
6-51
06
ISG Indication
The ISG System is indicated by lamp on
the instrument cluster. If your vehicle is
equipped with a supervision cluster, the
notice will illuminate on the LCD display.
OBC3060009
The system may require the engine to
manually restart when the light on the
ISG OFF button will illuminate and if your
vehicle is equipped with a supervision
cluster, a warning message comes on
continuously.
OBC3N061014AU
OBC3070110TU/OBC3070111TU
The engine will not start if the shift lever
is moved from the N (neutral) stage to
the D (driving) stage, manual mode, or R
(reverse) stage without stepping on the
brake pedal whilst the engine is stopped
automatically. At this time, if you press
the brake it will be restarted.
Page 325 of 649
6-52
Driving your vehicle
Conventional MT vehicle (not MHEV or
not equipped with LATE Restart) is able
to restart engine, only in Neutral gear.
If you select a gear, without depressing
clutch pedal fully, then warning will be
displayed with beep. You should restart
the engine in Neutral gear position.
Unintentionally, when the engine is
turned off or the vehicle is moving, if the
gear is engaged and the clutch pedal
is not pressed, the system displays the
warning message as shown below. At
this time, if the driver presses the clutch
pedal all the way, the engine restarts
automatically. (Only with Late Restart
equipped ISG system, except MHEV)
OPDE050564L
ISG malfunction
The system may not operate when:
OBC3060009
The ISG related sensors or system error
occurs.
The yellow AUTO STOP indicator
(
) on the instrument cluster will
stay on after blinking for 5 seconds and
the light on the ISG OFF button will
illuminate.
NOTICE
[ , I W K H , 6 * 2 ) ) E X W W R Q O L J K W L V Q R W
turned off by pressing the ISG OFF
button again or if the ISG system
continuously does not work correctly,
have your vehicle inspected by a
professional workshop as soon as
possible. Hyundai recommends
to contact a HYUNDAI authorised
repairer.
[ : K H Q W K H , 6 * 2 ) ) E X W W R Q O L J K W F R P H V
on, it may stop illuminating after
driving your vehicle at approximately
50 mph (80 km/h) for a maximum
of two hours and setting the fan
speed control knob below the 2nd
position. If the ISG OFF button light
continues to be illuminated in spite
of the procedure, have your vehicle
inspected by a professional workshop
as soon as possible. Hyundai
recommends to contact a HYUNDAI
authorised repairer.