coolant level Hyundai Matrix 2007 Owner's Guide

6 OWNER MAINTENANCE
14AIR CLEANER ELEMENT REPLACEMENT
G070A01E-EAT
HFC5003
Petrol engine
G070A02FC
Diesel engine
To replace the air cleaner element, remove the air intake ducting from theair flow sensor body and unfasten the spring clips holding the air flow sensor top to the body.
!
G050D02FC
6. Start the engine with the radiator cap still removed and continue to add coolant as the level decreases as air is expelled from the system.When the level remains constant, replace the radiator cap and replen- ish the coolant reservoir.
7. When the engine is hot, check to ensure that no coolant leaks arepresent. WARNING:
The cooling fan is controlled by
engine coolant temperature and maysometimes operate even when theengine is not running. Use extreme caution when working near the blades of the cooling fan so thatyou are not injured by a rotating fan blade. As the engine coolant tem- perature decreases, the fan will au-tomatically shut off. This is a nor- mal condition.
fcuk-6.p65 12/27/2006, 10:16 AM
14

6
OWNER MAINTENANCE
17
The level of windscreen washer fluid available should be checked on a daily basis. The level of fluid will be visible through the side of the reservoir.When the fluid is to be replenished, only a proprietary screen wash addi- tive should be used and in the concen- tration recommended by the manufac- turer. The windscreen washer reser- voir has a total capacity of 3 litres.
WINDSCREEN WASHER RESERVOIR REPLENISH- MENT
SG090A2-E
HFC5010
!CAUTION:
Engine coolant anti freeze must not be used in the windscreen washer system since damage to thepaintwork may result.
Undiluted windscreen washer addi-tive must not be allowed to comeinto contact with the paintwork. If spillage occurs, flush the affected area immediately with water. Do notoperate the windscreen washer for more than 15 seconds continuously or when the reservoir is empty since damage to the washer pump will result.
HHR5051
2. Pull up the wiper blade until you hear an audible "click" to engage in the end of the wiper arm.
NOTE: Do not allow the wiper arm to fall
against the windscreen.
fcuk-6.p65 12/27/2006, 10:16 AM
17

6
OWNER MAINTENANCE
21
!
3. Confirm that the fluid level is in
“HOT” range on the level gauge. If the fluid level is lower, add the specified fluid from the fill hole. If the fluid level is higher, drain thefluid from the drain hole.
4. If the fluid level is checked in cold condition (fluid temperature 20~30°C (68~86°F)) add the fluid to “COLD” line and then recheck the fluid levelaccording to the above step 2. WARNING:
The cooling fan is controlled by engine coolant temperature and may sometimes operate even when theengine is not running. Use extreme caution when working near the blades of the cooling fan so thatyou are not injured by a rotating fan blade. As the engine coolant tem- perature decreases, the fan will au-tomatically shut off. This is a nor- mal condition.
!
Fluid level should be within this range
C090A03FCWARNING (Diesel only):
Never work on injection system with engine running or within 30 sec- onds after shutting off engine. Highpressure pump, rail, injectors and high pressure pipes are subject to high pressure even after the enginestopped. The fuel jet produced by fuel leaks may cause serious injury, if it contacts the body. People using pacemakers should ensure that they keep a distance of 30cm from the ECU or wiring har-ness within the engine room whilst engine is running, since the high currents in the Common Rail sys-tem produce considerable magnetic fields.
fcuk-6.p65 12/27/2006, 10:16 AM
21

6
OWNER MAINTENANCE
31
!
SG220A1-E ELECTRIC COOLING FANS
WARNING:
The cooling fan is controlled by
engine coolant temperature and may sometimes operate even when the engine is not running. Use extreme caution when working near theblades of the cooling fan so that you are not injured by a rotating fan blade. As the engine coolant tem-perature decreases, the fan will au- tomatically shut off. This is a nor- mal condition.
The engine cooling fan should operate
before the temperature gauge reachesthe upper portion of the scale and thecondenser fan should operate when- ever the air conditioning is in use.
POWER STEERING FLUID LEVEL
SG230A1-E
HFC5004
G230A02FC
Petrol engine
Diesel engine
The power steering fluid level should be checked daily. To check the power steering fluid level, be sure the ignition is "OFF", thencheck to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings onthe fluid reservoir. NOTE: Grinding noise from power steering pump may be heard immediately after the engine is started in ex-tremely cold condition (below -4°F). If the noise stops dur- ing warm up, there is no abnormalfunction in the system. This is due to a power steering fluid character- istic in extremely cold conditions.
FLUID RECOMMENDATION Only automatic transmission fluidmeeting the specification of PSF-3 or Dexron 2 should be used in the power steering system.
fcuk-6.p65 12/27/2006, 10:16 AM
31

6 OWNER MAINTENANCE
34
G290A01FC
5. Open the bonnet.
6. Draw the vertical line (through the centre of each headlight beam pat- tern) and the horizontal line (through the centre of each headlight beampattern) on the aiming screen.And then, draw the horizontal paral-lel line at 1.18 in. (30 mm) under the horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillipsscrewdriver - VERTICAL AIMING
8. Adjust each cut-off line of the low beam to each vertical line with a phillips screwdriver - HORIZONTALAIMING.
Horizontal Aiming
Vertical Aiming
HEADLIGHT AIMING ADJUSTMENT
G290A01FC-EAT Before performing aiming adjustment,
make sure of the following.
1. Keep all tyres inflated to the correct
pressure.
2. Place the vehicle on level ground and press the front bumper & rear bumper down several times. Place the vehicle at a distance of 118 in. (3,000 mm) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,engine oil and fuel, and spare tyre,jack, and tools).
4. Clean the head lights lens and turn on the headlight (Low beam).
!WARNING:
o Do not smoke or have any other open flame near the vehicle whilst bleeding the fuel system.
o Be sure to carefully wipe away any water drained out in thismanner, because the fuel mixed in the water might be ignited and result in a fire.
Extracting air in the fuel filter If you drove until you have no fuel left
or if you replaced the fuel filter, be sureto extract air in the fuel system as it makes you difficult to start the engine.
1) Remove the air extract nozzle cap
on the fuel filter.
2) Pump up and down until the fuel flows out of the plug opening.
NOTE: Use cloths when you extract air so
that the fuel is not sprayed around. Clean the fuel around the fuel filteror the injection pump before start- ing the engine to prevent fire. Fi- nally, check each part if the fuel isleaking.
fcuk-6.p65 12/27/2006, 10:16 AM
34