garage door opener HYUNDAI PALISADE 2022 Owners Manual

3-41
Convenience Features
HomeLink®Wireless Control System
Your new mirror comes with an inte-
grated HomeLink Universal
Transceiver, which allows you to pro-
gram the mirror to activate your
garage door(s), estate gate, home
lighting, etc. The mirror actually
learns the codes from your various
existing transmitters.Retain the original transmitter for
future programming procedures (i.e.,
new vehicle purchase). It is also sug-
gested that upon the sale of the vehi-
cle, the programmed HomeLink but-
tons be erased for security purposes
(follow step 1 in the "Programming"
portion of this text).
Programming
Your vehicle may require the ignition
switch to be turned to the ACC posi-
tion for programming and/or operation
of HomeLink. It is also recommended
that a new battery be replaced in the
hand-held transmitter of the device
being programmed to HomeLink for
quicker training and accurate trans-
mission of the radio-frequency.
Follow these steps to train your
HomeLink mirror:
3
OHD046305N
Glare detection sensorIndicator light
Homelink buttons
When programming the
HomeLink®Wireless Control
System, you may be operating
a garage door or gate operator.
Make sure that people and
objects are out of the way of
the moving door or gate to pre-
vent potential harm or damage.
Do not use HomeLink with
any garage door opener that
lacks the safety stop and
reverse feature as required by
U.S. federal safety standards.
(This includes any garage
door opener model manufac-
tured before April 1, 1982.) A
garage door opener which
cannot detect an object, sig-
naling the door to stop and
reverse, does not meet cur-
rent U.S. federal safety stan-
dards. Using a garage door
opener without these features
increases risk of serious
injury or death. For more
details, call 1-800-355-3515 or
on the internet at www.home-
link.com.
WARNING

3-42
1. When programming the buttons forthe first time, press and hold the
left and center buttons ( , )
simultaneously for approximately
20 seconds until the indicator light
begins to flash. (This procedure
erases the factory-set default
codes. Do not perform this step to
program additional hand-held
transmitters.) For non rolling code garage door
openers, follow steps 2 - 3.
For rolling code garage door
openers, follow steps 2 - 6.
For Canadian Programming,
please follow the Canadian
Programming section.
For help with determining whether
your garage is non-rolling code or
rolling code, please refer to the
garage door openers owner's
manual or contact HomeLink cus-
tomer service at 1-800-355-3515.
2. Press and hold the button on the
HomeLink system you wish to train
and the button on the transmitter
while the transmitter is approxi-
mately 1 to 3 inches away from the
mirror. Do not release the buttons
until step 3 has been completed.
3. The HomeLink indicator light will flash, first slowly and then rapidly.
When the indicator light flashes
rapidly, both buttons may be
released. (The rapid flashing light
indicates successful programming
of the new frequency signal.)
NOTICE
Convenience Features
OHD046307N
Flashing
1-3inchesTransmitterOHD046306N
Flashing

3-43
Convenience Features
Some gate operators and garage
door openers may require you to
replace step #3 with the "cycling"
procedure noted in the "Canadian
Programming" section of this doc-
ument.
Rolling code programming
To train a garage door opener (or
other rolling code equipped devices)
with the rolling code feature, follow
these instructions after completing
the "Programming" portion of this
text. (A second person may make the
following training procedures quicker
& easier.)
4. Locate the "learn" or "smart" but-ton on the device's motor head
unit. Exact location and color of
the button may vary by product
brand. If there is difficulty locating
the "learn" or "smart" button, refer-
ence the device's owner's manual
or contact HomeLink at 1-800-
355-3515 or on the internet at
www.homelink.com. 5. Press and release the "learn" or
"smart" button on the device’s
motor head unit. You have 30 sec-
onds to complete step number 6.
6. Return to the vehicle and firmly press and release the pro-
grammed HomeLink button up to
three times. The rolling code
equipped device should now rec-
ognize the HomeLink signal and
activate when the HomeLink but-
ton is pressed. The remaining two
buttons may now be programmed
if this has not previously been
done. Refer to the "Programming"
portion of this text.
Operating HomeLink
To operate, simply press the pro-
grammed HomeLink button.
Activation will now occur for the
trained product (garage door, securi-
ty system, entry door lock, estate
gate, or home or office lighting). For
convenience, the hand-held trans-
mitter of the device may also be used
at any time. The HomeLink Wireless
Controls System (once programmed)
or the original hand-held transmitter
may be used to activate the device
(e.g. garage door, entry door lock,
etc.). In the event that there are still
programming difficulties, contact
HomeLink at 1-800-355-3515 or on
the internet at www.homelink.com.
NOTICE
3

3-45
Convenience Features
Integrated HomeLink®Wireless
Control System
The HomeLink®Wireless Control
System provides a convenient way to
replace up to three handheld radio-
frequency (RF) transmitters used to
activate compatible devices such as
gate operators, garage door open-
ers, entry door locks, security sys-
tems, and home lighting.
Considering the Home Security
when the vehicle is parked out-
side the garage, the HomeLink will
ONLY work when the ignition
switch is in ACC position or ON
position.
NOTICE
3
Before programming HomeLink
to a garage door opener or gate
operator, make sure that people
and objects are out of the way
of the device to prevent poten-
tial harm or damage. When pro-
gramming a garage door open-
er, it is advised to park outside
of the garage.
Do not use HomeLink with any
garage door opener that lacks
safety stop and reverse features
as required by U.S. federal safe-
ty standards (this includes any
garage door opener model man-
ufactured before April 1, 1982).
A garage door that cannot
detect an object signaling the
door to stop and reverse - does
not meet current U.S. federal
safety standards. For more
information, contact HomeLink
at www.homelink.com, or call
HomeLink customer support at
1-800-355-3515.
(Continued)
(Continued)
It is also recommended that a
new battery be replaced in the
hand-held transmitter of the
device being trained to
HomeLink for quicker training
and accurate transmission of
the radio frequency.WARNING

3-46
1. Programming homelink®
The following steps show how to pro-
gram HomeLink. If you have any
questions or are having difficulty pro-
gramming your HomeLink buttons,
refer o the HomeLink website or call
the HomeLink customer support toll-
free number. Do this, before going
back to the dealer who sold you the
car.
Visit the HomeLink website at:www.homelink.com. Then at the
top of the page, choose your vehi-
cle make. Then watch the You Tube
video, and/or access additional
website information.
If you choose to access the website via your cell
phone, scan the QR
code.
Or, call HomeLink customer sup- port at 1-800-355-3515 (Please
have the vehicle make/model AND
the opener device make/model
readily available.) 1) Programming Preparation
1. When programming a garage door
opener, it is advised to park the
vehicle outside of the garage.
2. It is recommended that a new bat- tery be placed in the hand-held
transmitter of the device being
programmed to HomeLink for
quicker training and accurate
transmission of the radio-frequen-
cy signal.
3. Place the ignition switch to the ACC(Accessory) position for pro-
gramming of HomeLink. 2) Programming a New HomeLink
Button
1. Press and hold the HomeLink but- ton (1), (2) or (3), you would like to
program (Fig. 2). The HomeLink
indicator light (4) will flash slowly
in red (if not, perform the steps of
“Erasing HomeLink Buttons” sec-
tion, and start over).
Convenience Features
OHD046025N

3-47
Convenience Features
2. Position the garage door openerremote 1 – 3 inches (2 – 8 cm)
away from the HomeLink buttons
(Fig. 3). 3. While the HomeLink indicator light
(4) (Fig. 2) is flashing slowly in red,
press and hold the hand-held
remote button. Continue pressing
the HomeLink button and the
hand-held remote button until the
HomeLink indicator light (4) light
changes from slowly to rapidly. You
may now release the buttons. 4. Wait until your garage door comes
to a complete stop, regardless of
position, before proceeding to the
next steps.
5. Press the HomeLink button you are programming and observe the
indicator light.
es or solid red, your device
should operate when the
HomeLink button is pressed. At
this point, if your device operates,
programming is complete.
es, firmly press, hold for two sec-
onds and release the HomeLink
button up to three times in a row
slowly to complete the program-
ming process. Do not press the
HomeLink button rapidly. At this
point if your device operates, pro-
gramming is complete. If the
device does not operate, contin-
ue with step P6.
3
OHD046025NOHD046307N
Flashing
1-3 inches

3-48
6. At the garage door opener motor,(security gate motor, etc.) locate
the “Learn,”,”Smart”, “Set” or
“Program” button (Fig. 4). This can
usually be found where the hang-
ing antenna wire is attached to the
motor-head unit (see the device’s
manual to identify this button). The
name and color of the button may
vary by manufacturer.
[A] : LEARN BUTTON
A ladder and/or second person
may simplify the following steps. 7. Firmly press and release the
“Learn”, “Smart”, “Set” or
“Program” button. You now have
up to 30 seconds in which to com-
plete the next step.
8. Return to the vehicle and firmly press, hold for two seconds and
release, the HomeLink button up
to three times in a row slowly. Do
not press the HomeLink button
rapidly. As soon as you see the
garage door start to move, stop
pressing any buttons until a few
seconds after the garage door has
come to a complete stop, regard-
less of position. At this point pro-
gramming is complete and your
device should operate when the
HomeLink button is pressed and
released.
NOTICE
Convenience Features
ODL3A040504

3-49
Convenience Features
2. Operating homelink®
1) Operating HomeLink
1. Press the desired programmedHomeLink button (1, 2 or 3). The HomeLink indicator (4)
should flashing in red or solid red,
and your programmed device
should operate.
If your device does not operate,
the HomeLink programming was
not successful, and you’ll need to
reprogram the button.
3. Erasing homelink®buttons
If you recently purchased your vehi-
cle and are programming HomeLink
for the first time, we recommend that
you follow the instructions below to
erase ALL HomeLink programming.
For new vehicles, there should not
be any programming associated with
any of the buttons. But clear them all
out anyway, if you are having any
programming issues. If you pur-
chased your vehicle “used”, then
you’ll need to erase ALL HomeLink
programming so the unit is clear to
accept new programming for your
devices. If you have owned your vehicle for
some time, and already have pro-
grammed one or more of the buttons,
there may be situations where you
only want to erase and reprogram a
single button. For example, you
move to a new home, and need to
erase and reprogram only button 1
for your personal garage door, and
you want to KEEP the programming
of buttons 2 and 3. The same would
be true if you had to purchase a
replacement garage door opener for
your current home. Therefore, if you
want to erase and reprogram a sin-
gle button, while keeping the pro-
gramming of one or more of the other
buttons, follow the instructions for
erasing and reprogramming a single
button.
NOTICE
3
OHD046025N
OHD046025N