display HYUNDAI PALISADE 2023 Owner's Guide

Convenience Features5-40
System Precautions

[ Make sure that all the windows are
closed. If the window is open, the
alert may operate by the sensor
detecting an unintended movement
(for example, wind or bugs).

[
B0116EU01
A: Cluster,
B: Steering wheel
If you do not want to use Rear
Occupant Alert, press the OK button
on the steering wheel when the first
alert is displayed on the cluster. Doing
so will deactivate the second alert one
time.

[ An alert can occur if the there is an
impact on the roof.

[ If boxes or objects are stacked in the
vehicle, the system may not detect
the boxes or objects. Or, the alert may
operate if the boxes or objects fall off.

[ The sensor may not operate normally
if the senor is obscured by foreign
substances.

[ The alert may operate if movement
in the driver or passenger seat is
detected.

[ The alert may operate with the doors
locked due to car wash or surrounding
vibration or noise.

[ If the vehicle is started remotely (if
equipped with Remote Start), inside
movement detection will stop.
WARNING
Even if your vehicle is equipped with
Rear Occupant Alert, always make sure
to check the rear seat before you leave
the vehicle.
Rear Occupant Alert may not operate
when:

[Movement does not continue for
a certain period of time or the
movement is small.

[ The rear passenger is covered with
an object such as a blanket.

[ Always be cautious of the
passenger’s safety as the detection
function and second alert may
not operate depending on the
surrounding environment and
certain conditions.

05
5-41
B0122KO01
The IMS, or Integrated Memory System,
for the driver’s seat is provided to store
and recall the following memory settings
with a simple button operation.

[Driver’s seat position

[ Side view mirror position

[ Head-Up Display (HUD) position (if
equipped)
WARNING
Never attempt to operate the
integrated memory system while the
vehicle is moving.
This could result in loss of control, and
an accident causing death, serious
injury, or property damage.
Information

[If the battery is disconnected, the
memory settings will be erased.

[ If the Integrated Memory System does
not operate normally, have the system
inspected by an authorized HYUNDAI
dealer.
Storing Memory Positions
1. Shift to P (Park) while the Ignition
switch is in the ON position.
2. Adjust the driver’s seat position, side view mirror position and head-up
display height to the desired position.
3. Press the SET button. The system will beep once and notify you ‘Press
button to save settings’ on the cluster
LCD display.
4. Press one of the memory buttons (1 or 2) within 4 seconds. The system
will beep twice when the memory has
been successfully stored.
5. ‘Driver 1 (or 2) settings saved’ will appear on the cluster LCD display. The
message appears only for the driver’s
seat position memory setting.
,17(*5$7('0(025<6<67(0

Convenience Features5-42
Recalling Memory Positions
1. Shift to P (Park) while the Ignition switch is in the ON position.
2. Press the desired memory button (1 or 2). The system will beep once,
and then the driver’s seat position,
side view mirror position and head-
up display height will automatically
adjust to the stored positions.
3. ‘Driver 1 (or 2) settings applied’ will appear on the cluster LCD display.
Information

[Note that while the memory settings
are being recalled, if you press the
SET button or the corresponding IMS
memory button (1 or 2) for which the
settings are being recalled, the IMS will
temporarily deactivate. If you select the
alternate IMS memory button (1 or 2),
the IMS will activate according to the
settings of the alternate button.
For example, if you press the SET
button or the number 1 button with the
number 1 setting in operation, the IMS
will temporarily deactivate.
If you press the number 2 button, then
the IMS memory settings according to
number 2 will activate.

[ If you adjust the driver’s seat, side vew
mirror or head-up display while the
IMS is recalling the stored positions,
the memory settings will not be applied.
Resetting the System
Follow the below procedures to reset the
Integrated Memory System (IMS) if it is
not operating properly:
Resetting integrated memory
system
1. Stop the vehicle and open the driver’s
door with the vehicle shifted to P
(Park).
2. Adjust the driver’s seat and seatback to the foremost position.
3. Press the SET button and push forward the driver’s seat movement
switch over 2 seconds simultaneously.
While resetting integrated memory
system
1. Resetting starts with a notification sound.
2. The driver’s seat and seatback is adjusted to the rearward position with
the notification sound.
3. The driver’s seat and seatback is re-adjusted to the default position
(central position) with the notification
sound.
However, in the following cases, the
resetting procedure and the notification
sound may stop.

[ The memory button is pressed.

[ The seat control switch is operated.

[ The driving speed exceeds 2 mph
(3 km/h).

[ The driver’s door is closed.

Convenience Features5-52
3) Two-Way Communication Programming (For select garage door
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:

à A ladder and/or second person may
simplify the following steps. 2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication programming is now complete.
Information
If your garage door opener has Two-
Way Communication functionality,
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
Way Communication Programming
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
Button” and “Two-Way Communication
Programming” will restore door
operation.

05
5-53
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light S is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
S changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.
2. Operating HomeLink®
1) Operating HomeLink®
B0135EU05
1. Press and release the desired programmed HomeLink button (M, N
or O).
Information
The HomeLink indicator S should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.
2) Two-Way Communication Display
Behavior
B0135EU07
1. Press and release one of the programmed HomeLink buttons (M,
N or O).
B0135EU08
2. The indicator P and R operates as
below, if your garage door opener
has Two-Way Communication
functionality.

Convenience Features5-60
The Digital Center Mirror is a system
that uses the camera on the rear of the
vehicle and displays its image on the
screen of the Digital Center Mirror. The
Digital Center Mirror allows the driver to
see the rear view despite obstructions,
such as the headrest or luggage,
ensuring rear visibility.
WARNING

[ )DLOXUHWRIROORZWKHZDUQLQJVDQG
instructions for proper use of the
Digital Center Mirror could result in
serious accident.

- The Digital Center Mirror is a
convenience feature but it is not
a substitute for proper vehicle
operation. The system has areas
where objects cannot be viewed.
Check the blind spot of the Digital
Center Mirror before vehicle
operation. The driver is always
responsible for safe driving.

- Do not operate the Digital Center
Mirror while driving. Doing so
cannot be a distraction and it could
lose control of your vehicle and
cause an accident or serious injury.

- Do not disassemble or modify the
Digitaal Center Mirror, the camera
unit or wirings. If you do, it may
result in accidents or fire. In case
you notice smoke or smell coming
from the Digital Center Mirror, stop
using the system immediately.
Have you see an authorized
HYUNDAI dealer for servicing.
[
Be sure to adjust the Digital Center
Mirror before driving.

- Switch the system to the
conventional rearview mirror
mode and be properly seated on
the driver’s seat. Then adjust the
mirror so as to see the rear window
properly.

- Push the lever all the way to change
to digital mirror mode and adjust
the display settings. Driving without
adjusting the mirror may cause
difficulty in watching the display
at the Digital Mirror mode (camera
view mode) due to the reflection
from the surface of the mirror.

- As the range of the image display
by the Digital Center Mirror is
different from that of the optical
mirror, make sure to check this
difference before driving.

[ If the Digital Center Mirror
malfunction, immediately switch the
system to the conventional rearview
mirror mode.

[ When strong light (for example,
sunlight or high beams from
following vehicles) enters the
camera, a light beam or a glaring
light may appear on the monitor
screen of the Digital Center Mirror.
In that case, switch the system to the
conventional rearview mirror mode
appropriately.

[
B0362KO01
If the camera lens M is dirty, the
displayed image may not be clear.
In this case, clean it with a soft cloth
dampened with water or a swab.
',*,7$/&(17(50,5525

05
5-61
System component
ONE1052295N
1. Icon display areaDisplays icons, adjusting Brightness
& Tilt
2. Lever Operate to change between digital
mirror mode and optical mirror mode.
3. Menu button Press to display the icon display area
and select the item you want to adjust
(Brightness & Tilt).
4. Select/adjust button
Press to change the setting of the
item you want to adjust.
5. Camera indicator Indicates that the camera is operating
normally.
6. HomeLink buttons For the operation of the “HomeLink®
Universal Transceiver”.
How to change the mode
ONE1052296
The mode can be switched when the
switch is in the ON position.
1. Pull the mode select lever to all the way switch to the Digital Center Mirror
mode (camera view mode).

à Displays an image of the area behind
the vehicle. In this mode, camera
indicator R is shown.
2. Push the mode select lever to all the way switch to the optical inside
rearview mirror mode

à Turns off the display of the Digital
Center Mirror allows it to be used as
an optical mirror.

Convenience Features5-62
Adjusting the mirror height
B0913EU03
The height of the rearview mirror can be
adjusted to suit your driving posture.
Change to optical mirror mode, adjusting
the rearview mirror angle by moving it up
and down.
Display settings (Digital mirror
mode)
B0913EU01
1. Press the menu button M. The icons will be displayed.
Icons Settings
Select to adjust the brightness
of the display.
Select to adjust the display
up/down.
2. Press the menu button M repeatedly
and select the item you want to
adjust.
3. Press the button N or button O to change the setting.
The icons will disappear if the button
is not operated for approximately 5
seconds or more.

à If the brightness of the Digital Center
Mirror is set too high, it may cause eye
strain.
Adjust the Digital Center Mirror to
and appropriate brightness. If your
eyes become tired, change to optical
mirror mode.

05
5-63
B0913EU04
To prevent the light sensors from
malfunctioning
To prevent the light sensors from
malfunctioning, do no
t touch or cover
them.
Digital mirror mode operating
condition
The START/STOP button is in the ON
position.
When the START/STOP button is
changed ignition switch LOCK/OFF
or ACC position, the image will be
disappeared.
When using the Digital Center Mirror
in digital mirror mode

[ When the liftgate is open, the Digital
Center Mirror image may not display
properly. Before driving, make sure
the liftgate is closed.

[ If the display is difficult to see due to
reflected light, close the sunshade for
the sunroof (if equipped).

[ Any of the following conditions may
occur when driving in the dark, such
as at night. None of them indicates
that the malfunction has occurred.

- Colors of objects in the displayed
image may differ their actual color.

- Depending on your physical
condition or age, it may take longer
than usual to focus on the displayed
image. In this case, change to
optical mirror mode.

- Do not let passengers stare at the
displayed image when the vehicle is
being driven, as doing so may cause
motion sickness.

Convenience Features5-64
When the system malfunctions
B0913EU02
If the symbol shown in the illustration is
displayed when using the Digital Center
Mirror in digital mirror mode, the system
may be malfunctioning. The symbol will
disappear in a few seconds. Operate the
lever, change to optical mirror mode
and have the vehicle inspected by an
authorized HYUNDAI dealer.
CAUTION

[ To prevent the Digital Center Mirror
from malfunctioning

[ Do not use detergents, such as
thinner, benzene, and alcohol to
clean the mirror. They may dis color,
deteriorate or damage the mirror
surface.

[ Do not remove, disassemble or
modify the mirror and camera.

[ Do not allow an organic solvent,
vehicle wax, window cleaner or glass
coating to adhere to the camera. If
this happens, wipe it off as soon as
possible.

[ When cleaning the camera lens, wipe
the camera lens with a damp soft
cloth.

[ Do not strongly rub the camera lens,
as it may be scratched and will not be
able to transmit a clear image.
[
Do not subject the camera to a
strong impact as this could cause
a malfunction. If this happens,
we recommend that you have the
vehicle inspected by an authorized
HYUNDAI dealer as soon as possible.

[ Operating the system at the ON
position while the engine is not
running would cause discharging of
the battery.

[ Do not attach an antenna of wireless
device near the Digital Center Mirror.
Electric wave from wireless device
may cause disturbed image in Digital
Center Mirror.

[ Do not push buttons excessively
or operating the lever roughly may
cause a system failure or the Digital
Center Mirror itself to drop.

[ Never rotate the body of Digital
Center Mirror by 90° or more. It may
damage the Digital Center Mirror. Do
not apply strong shocks to the body
of Digital Center Mirror. It may cause
a system failure.

[ If it is difficult to see the Digital
Center Mirror display screen because
of a strong external light, switch the
mode to the conventional rearview
mirror mode for better use.