warning light HYUNDAI PALISADE 2023 Owner's Guide

Instrument Cluster4-24
Battery discharging due to external
electrical devices (if equipped)
This message is displayed if the battery
voltage is weak due to any non-factory
electrical accessories (ex. dashboard
camera) while parking. Be careful that
the battery is not discharged.
If the warning message appears after
removing the non-factory electrical
accessories, have the vehicle inspected
by an authorized HYUNDAI dealer.
Press START button with key
(for smart key system)
This warning message is displayed if you
press the Engine Start/Stop button while
the warning message "Key not detected"
is displayed.
At this time, the immobilizer indicator
light blinks.
Place digital key on the wireless
charger to keep the vehicle running
If the vehicle is remotely started and
‘Start Vehicle’ is deselected from the
Settings menu in the infotainment
system screen for Driver 1 and Driver 2,
this message will be displayed for up to
30 seconds when a door is opened after
unlocking the doors with a digital key.
To drive your vehicle, place the
registered digital key on the wireless
charger, when this message appears.
Vehicle is On (started by digital key)
This message is displayed for up to 10
seconds if the driver's door is opened
without the driver's seat belt fastened
after turning on the engine with a digital
key. After the message is displayed, a
warning sounds when the door is closed.
Information
Since the engine was started with a digital
key, if the engine is turned off, and there is
no smart key or digital key in the vehicle,
it may be difficult to start the engine
again.
Place saved digital key on wireless
charger, then press the START
button
This message is displayed for 6 seconds
and the immobilizer indicator light
(
) will blink for 10 seconds after the
message “Press START button with key”
is displayed for 4 seconds if the smart
key is not in the vehicle or not detected,
or the digital key is not placed on the
wireless charger when you press the
Engine Start/Stop button. To start the
vehicle, place a registered digital key on
the wireless charger, and then press the
Engine Start/Stop button.
Scan an authorized fingerprint, then
press the START button
This message is displayed for 6 seconds
and the immobilizer indicator light
(
) will blink for 10 seconds after the
message “Press START button with key”
is displayed for 4 seconds if the smart
key is not in the vehicle or not detected,
or your fingerprint is not verified when
you press the Engine Start/Stop button.
To start the vehicle, have an authorized
fingerprint verified on the fingerprint
sensor, and then press the Engine Start/
Stop button.
Digital key(s) active
This message is displayed for 4 seconds
when a smartphone key or NFC card
key is registered, and vehicle doors are
locked and unlocked after more than
10 minutes and the ignition switch is
placed to the ON position. The message
is not displayed again until more than 10
minutes have passed after the doors are
relocked.

04
4-27
Low washer fluid
This message is displayed if the washer
fluid level in the reservoir is nearly empty.
Have the washer fluid reservoir refilled.
Low fuel
This message is displayed if the fuel tank
is almost out of fuel.
When this message is displayed, the low
fuel level warning light in the cluster will
come on.
It is recommended to look for the nearest
fueling station and refuel as soon as
possible.
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended Lubricants and
Capacities“ section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
Information
After adding engine oil, if you travel
approximately 31~62 miles (50~100 km)
after the engine warms up, the warning
message should disappear.
If the warning message remains on, have
the vehicle inspected by an authorized
HYUNDAI dealer as soon as possible.
Engine overheated
This message is displayed when the
engine coolant temperature is above
approximately 248°F (120°C). This means
that the engine is overheated and may
be damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check haptic steering wheel system
This message is displayed if there is a
problem with the haptic steering wheel
system. Have the vehicle inspected by an
authorized HYUNDAI dealer.
Check headlight
This message is displayed if the
headlights are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check turn signal
This message is displayed if the turn
signal lamps are not operating properly.
A lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same wattage
rating.
Check headlight LED (if equipped)
This message is displayed if there is a
problem with the LED headlight. Have
the vehicle inspected by an authorized
HYUNDAI dealer.

05
5-5
Using Remote Key (if equipped)
B0921EU01
B0921EU02
Your HYUNDAI uses a remote key, which
you can use to lock or unlock the driver
and passenger doors or the liftgate.
M Door Lock
N Door Unlocka
O Liftgate Unlock (if equipped)
P Panic
Locking
To lock :
M Close all doors, engine hood and liftgate.
N Press the Door Lock button M on the remote key.
O The doors will lock. The hazard warning lights will blink.
P Make sure the doors are locked by checking the indicator light on the
driver side door lock button.
WARNING
Do not leave the Remote key in
your vehicle with children that are
unattended or unsupervised.
Children could inadvertently press
the Engine Start/Stop button or could
operate the power windows or other
vehicle controls or even cause the
vehicle to move. This could result in
serious injury or death.
Unlocking your vehicle
To unlock your vehicle :
1. Press the Door Unlock button N on the remote key.
2. The driver’s door will unlock. The hazard warning lights will blink two
times.
Two Press Unlock Feature
The priority for unlocking the driver door
only, or unlocking all the doors with
one press may be adjusted in the User
Settings mode in the cluster LCD display.
The Two Press Unlock feature, when
enabled, will require the user to press
the door unlock button once for driver
door only and twice for unlocking all the
doors.
You can activate or deactivate the Two
Press Unlock feature from the Settings
menu in the infotainment system.
Select:
- 6HWXS

Convenience Features5-6
The Two Press Unlock feature can also be
enabled or disabled by pressing the door
lock and unlock buttons simultaneously
on the Key:
Press and hold both the Door Lock
button and the Door Unlock button
simultaneously until the hazard warning
lights blink.
This will enable or disable the Two Press
Unlock feature. Repeat this procedure to
enable/disable the mode again.
Information
After unlocking the doors, the doors will
automatically relock after 30 seconds
unless a door is opened.
Liftgate unlocking (if equipped)
To unlock the liftgate :
1. Press and hold the Liftgate Unlock button O on the remote key for more
than one second.
2. The hazard warning lights will blink two times and the liftgate will open.
3. Once the liftgate is opened and then closed, the liftgate will automatically
re-lock after 30 seconds.
Information
The word “HOLD” is written on the
button to inform you that you must press
and hold the button for more than one
second.
Panic alarm
The horn sounds and the hazard warning
lights blink for about 30 seconds if this
button P is pressed for more than 1
second. To stop the horn and lights,
press any button on the transmitter.
Start-up
For detailed information refer to “Ignition
switch” in chapter 6.
NOTICE
To prevent damaging the remote key:

[Keep the remote key away from
liquids or any type of extreme heat.
If water or liquid gets inside of the
remote or if the remote is subjected
to extreme heat, damage to the
internal circuit may result. This
would void the vehicle warranty.

[ Avoid dropping or throwing the
remote key.

[ Protect the remote key from extreme
temperatures.

05
5-9
Locking your vehicle (Button type)
B0097KO01
To lock your vehicle using the door
handle button or the Smart Key:
1. Make sure all doors, the hood and the liftgate are closed.
2. Make sure you have the smart key in your possession.
3. Press either the button on the door handle or the Door Lock button M on
the smart key. The chime will sound
once and the hazard warning lights
will blink.
4. Make sure the doors are locked by checking the position of the door lock
button inside the vehicle.
Even though you press the outside
door handle button, the doors will not
lock and the chime will sound for three
seconds if any of the following occur:

[ The Smart Key is in the vehicle.

[ The ignition switch is in ACC or ON
position.

[ Any door except the liftgate is open.
Locking your vehicle (Touch sensor
type)
B0097EU02
1. Make sure that all doors are closed.
2. While having the Smart Key in your
possession, touch the outer part of
the door handle on or near the handle
detent for about 1 second or until you
hear the door locks actuate.
3. The doors will be locked. If the liftgate was open, then when the liftgate is
closed it will be locked also.
The chime will sound once and the
hazard warning lights will blink.

[ The door handle button will only
operate when the smart key is within
28~40 inches (0.7~1 m) from the
outside door handle.

[ Make sure the doors are locked by
pulling the door handle. If you locked
the door with the touch sensor on
the door handle, the doors cannot
be unlocked with the sensor within 3
seconds.

Convenience Features5-10
Note that if you press the outside door
handle to lock the doors using the touch
sensor, the doors will not lock under the
following circumstances:

[ The Smart Key is in the vehicle

[ The Engine Start/Stop button is in the
ACC or ON position

[ Any of the doors are open (except for
the liftgate)
If this occurs, then a chime will sound
for about 3 seconds. Check the vehicle
before attempting to lock the car again.
CAUTION
Before you leave your vehicle with the
Smart Key, verify that your vehicle is
locked. When using the touch sensor
on the front door handle, listen to hear
that the lock has actuated, and then
pull the handle within 3 seconds to
confirm the doors are locked.
(If it has been longer than 3 seconds,
verify the doors are locked by pressing
the lock button on the Smart Key. You
will hear a single beep.)
WARNING
Do not leave the Smart Key in
your vehicle with children that are
unattended or unsupervised.
Children could inadvertently press
the Engine Start/Stop button or could
operate the power windows or other
vehicle controls or even cause the
vehicle to move. This could result in
serious injury or death.
Unlocking your vehicle (Button type)
B0097KO01
1. Have the smart key with you.
2. Press the door handle button or press the Door Lock button N on the smart
key to unlock the doors. The chime
sounds and hazard warning lights
blink two times.
If you unlock the doors using the
passenger side door handle, all the
doors are unlocked. If you unlock
the doors using the driver side door
handle, either the driver's side door is
unlocked or all the doors are unlocked
depending on the setting for the Two
Press Unlock feature.
Information

[ Change the Driver Door unlock mode
by referring to "Setting the Two Press
Unlock feature".

[ The door handle button or touch sensor
only operates when the smart key is
within 28-40 inches (0.7-1 m) from the
outside door handle.

[ If you do not open the door after
unlocking within 30 seconds, it returns
to the lock mode.

05
5-11
Unlocking your vehicle (Touch
sensor type)
B0097EU03
1. Have the smart key with you.
2. Press the Door Unlock button N on the Smart Key or simply Grab the door
handle inside portion to activate the
unlock door touch sensor to unlock
the doors. The chime sounds and
hazard warning lights blink two times.
If you unlock the doors using the
passenger side door handle, all the
doors are unlocked. If you unlock
the doors using the driver side door
handle, either the driver's side door is
unlocked or all the doors are unlocked
depending on the setting for the Two
Press Unlock feature.
Information

[Change the Driver Door unlock mode
by referring to User Settings.

[ The door handle button or touch sensor
only operates when the smart key is
within 28-40 inches (0.7-1 m) from the
outside door handle.

[ If you do not open the door after
unlocking within 30 seconds, it returns
to the lock mode.

[ If you unlock the door with the door
handle, the doors cannot be locked with
the touch sensor within 2 seconds. To prevent unintentional door lock or
unlock:
Press the lock button on the smart key
and immedia

tely press the unlock button
along with the lock button for more than
4 seconds. The hazard warning lights will
blink four times. At this time, the doors
will not lock or unlock even though the
touch sensor is touched on the outside
door handle.
To deactivate the function, press the
door lock or unlock button on the smart
key.
Setting the Two Press Unlock feature
You can activate or deactivate the Two
Pr
ess Unlock feature from the Settings
menu in the infotainment system.
Select:

- 6HWXS

Convenience Features5-12
Opening the liftgate
Non-power liftgate
To unlock and open the liftgate:
1.
Make sure you have the smart key in
your possession.
2. Press either the liftgate handle release switch on the vehicle for more than
one second. The hazard warning lights
will blink two times and the liftgate
latch will unlock.
3. Once the liftgate is opened and then closed, the liftgate will automatically
re-lock after 30 seconds.
Information
The liftgate handle switch will only
operate when the smart key is within 28
inches (0.7 m) from the liftgate handle.
Power liftgate
To unlock and open the liftgate:
1.

Make sure you have the smart key in
your possession.
2. Press either the liftgate handle release switch on the vehicle or press and
hold the Liftgate Unlock button P
on the smart key for more than one
second. The hazard warning lights will
blink two times and the liftgate latch
will open.
3. Once the liftgate is opened and then closed, the liftgate will automatically
re-lock after 30 seconds.
Information
The liftgate handle switch will only
operate when the smart key is within 28
inches (0.7 m) from the liftgate handle.
Remotely starting vehicle
(if equipped)
You can start the vehicle using the
Remote Start button on the smart key.
To start the vehicle remotely:
1. Before you can use remote start your vehicle, the door lock button must be
pressed. Press the door lock button
on the Smart Key. You must be within
about 32 feet (10m) from your vehicle.
2. Press and hold the remote start button on your Smart Key. You must
press the button within 4 seconds
from when you pressed the door lock
button to activate the remote start.
3. The hazard warning lights will blink and the engine will start.
4. To turn off the remote start function, press the Remote Start button once.

05
5-13
Information

[Laws in your country may restrict the
use of remote start. You should check
country regulations before using this
remote starting system.

[ The vehicle must be in P (Park) for the
remote start function to start.

[ The engine turns off if you get on the
vehicle without a registered smart key.

[ The engine turns off if you do not get
on the vehicle within 10 minutes after
remotely starting the vehicle.

[ The Remote Start button may not
operate if the smart key is not within 32
feet (10 m).

[ The vehicle will not remotely start if the
engine hood or liftgate is opened.

[ Do not idle the engine for a long period.

[ The Remote start function works the
same as Blue Link remote start. For
further caution information, refer to
the separately supplied “Blue Link
(Infotainment system) manual”.
Remote Smart Parking Assist
Feature (if equipped)
Some models are equipped with Remote
Smart Parking Assist Feature. With the
Smart Key, the vehicle can be moved
forward or backward remotely to enter or
exit a tight parking space.
For more details, refer to “Remote Smart
Parking Assist (RSPA)” section in chapter
7.
Panic alarm
The horn sounds and the hazard warning
lights blink for about 30 seconds if this
button is pressed for more than 1 second
To stop the horn and lights, press any
button on the transmitter.

Convenience Features5-14
Start-up (if equipped)
Some models are equipped with a push
button start instead of a key cylinder.
You can leave your Smart Key in your
pocket or purse when you start your
vehicle.
For more details, refer to the “Engine
Start/Stop Button” section in chapter 6.
Information
Preventing the doors/liftgate from locking/
unlocking

[ Activating the feature
With the engine off, press the
lock button on the smart key and
immediately press the unlock button
along with the lock button for more
than 4 seconds. When the feature is
activated, the hazard warning lights
will blink four times.

[ How the feature works
When the feature is activated, the
doors or liftgate will not lock or unlock
even though the outside door handle
button or liftgate handle release switch
is pressed with the smart key in your
possession. Also, Welcome System
(if equipped) and Smart Liftgate (if
equipped) will not operate even though
you approach the vehicle with the
smart key.

[ Deactivating the feature
Press the door lock or unlock button
on the smart key, the feature will
deactivate.
Information
If the smart key is not moved for some
time, the detection function for smart key
operation will pause. Lift the smart key to
activate the detection again.
NOTICE
To prevent damaging the smart key:

[Keep the smart key in a cool,
dry place to avoid damage or
malfunction. Exposure to moisture
or high temperature may cause
the internal circuit of the smart key
to malfunction which may not be
covered under warranty.

[ Avoid dropping or throwing the
smart key.

[ Protect the smart key from extreme
temperatures.