battery HYUNDAI PALISADE 2023 Service Manual

Convenience Features5-160
Information
B0920EU02

[ Rated voltage : AC 115 volts

[ Maximum electric power : 150 watts

[ In order to avoid an electrical system
failure, electric shock, etc., be sure to
read owner’s manual before use.

[ Be sure to close the cover except the
time of use.
WARNING
To reduce a risk of serious or fatal
injuries:

[Do not use a heated electric device
such as a coffeepot, toaster, heater,
iron, etc.

[ Do not insert foreign objects into the
outlet and do not touch the outlet as
you may get shocked.

[ Do not let children touch the AC
inverter.
NOTICE

[To prevent the battery from being
discharged, do not use the AC
inverter while the engine is not
running.

[ When not using the AC inverter,
make sure to close the AC inverter
cover.

[ After using an electric accessory
or equipment, pull the plug out.
Leaving the accessory or equipment
plugged in for a long time may cause
battery discharge.

[ Do not use an electric accessory or
equipment the power consumption
of which is greater than 220
volts/200 watts.

[ Some electric accessories or
equipment can cause electronic
interference. It may cause excessive
audio noise and malfunctions in
other electric systems or devices in
the vehicle.

[ Do not use broken electric
accessories or equipment, which
may damage the AC inverter and
electrical systems of the vehicle.

[ Do not use two or more electric
accessories or equipment at the
same time. It may cause damage to
the electrical systems of the vehicle.

[ When the input voltage is lower,
outlet LED will blink and the AC
inverter will turn off automatically. If
the input voltage goes up to normal,
the AC inverter will turn on again.

6
Before Driving ........................................................................\
........................... 6-4Before Entering the Vehicle ........................................................................\
................ 6-4
Before Starting ........................................................................\
.................................... 6-4
Ignition Switch ........................................................................\
.......................... 6-5Key Ignition Switch ........................................................................\
...............................6-5
Engine Start/Stop Button ........................................................................\
................... 6-8
Vehicle Auto-Shut Off ........................................................................\
.............. 6-13Operating Conditions ........................................................................\
........................ 6-13
Deactivating Conditions ........................................................................\
................... 6-13
System Operation ........................................................................\
............................... 6-13
Automatic Transmission ........................................................................\
..........6-14Automatic Transmission Operation ........................................................................\
... 6-14
LCD Display Messages (Cluster) ........................................................................\
....... 6-20
Paddle Shifter (Manual Shift Mode) ........................................................................\
.. 6-25
Good Driving Practices ........................................................................\
...................... 6-25
Braking System ........................................................................\
........................6-27
Power-Assist Brakes ........................................................................\
........................... 6-27
Disc Brakes Wear Indicator......................................................................\
.................. 6-27
Electronic Parking Brake (EPB) ........................................................................\
..........6-28
Auto Hold ........................................................................\
...........................................6-33
Anti-Lock Brake System (ABS) ........................................................................\
.......... 6-36
Electronic Stability Control (ESC) ........................................................................\
.... 6-38
Vehicle Stability Management (VSM) ...................................................................... 6-40
Hill-Start Assist Control (HAC) ........................................................................\
.......... 6-42
Trailer Stability Assist (TSA) ........................................................................\
.............. 6-42
Downhill Brake Control (DBC) ........................................................................\
.......... 6-43
Good Braking Practices ................................................................\
............................ 6-46
All Wheel Drive (AWD) ........................................................................\
............ 6-47All Wheel Drive (AWD) Operation ........................................................................\
......6-47
AWD Operation ........................................................................\
.................................. 6-48
Emergency Precautions ........................................................................\
.................... 6-50
Idle Stop and Go (ISG) ........................................................................\
........... 6-52ISG System Operation ........................................................................\
........................6-52
ISG System Off ........................................................................\
.................................. 6-54
Forced to Restart Engine ........................................................................\
...................6-55
ISG Malfunction ........................................................................\
..................................6-55
Calibrating the Battery Sensor ........................................................................\
..........6-55
6. Driving Your Vehicle

Driving Your Vehicle6-6
Key Ignition Switch Positions
Switch
Position Action Notes
LOCK T
o turn the ignition switch to the LOCK
position, push the key in at the ACC
position and turn the key towards the
LOCK position.
The ignition key can be removed in
the LOCK position.
The steering wheel locks to protect
the vehicle from theft. (if equipped)
ACC Some electrical accessories are
usable. The steering wheel unlocks.
If difficulty is experienced turning the
ignition switch to the ACC position,
turn the key while turning the steering
wheel right and left to release.
ON This is the normal key position when
the engine has started. All features
and accessories are usable.
The warning lights can be checked
when you turn the ignition switch
from ACC to ON. Do not leave the ignition switch in the
ON position when the engine is not
running to prevent the battery from
discharging.
START To start the engine, turn the ignition
switch to the START position. The
switch returns to the ON position
when you let go of the key. The engine will crank until you release
the key.

06
6-9
Engine Stop/Start Button Positions
Button PositionAction Notes
OFF T
o turn off the engine, press the
Engine Start/Stop button with the
vehicle shifted to P (Park).
Note if the Engine Start/Stop
button is pressed with the vehicle
shifted to D (Drive) or R (Reverse),
the gear will automatically shift to
P (Park).
If the Engine Start/Stop button is
pressed with the gear shifted to
N (Neutral), the Engine Start/Stop
button will change to the ACC
position.
ACC Press the Engine Start/Stop button
when the button is in the OFF
position without depressing the
brake pedal.
Some of the electrical accessories
are usable. If you leave the Engine Start/Stop
button in the ACC position for
more than one hour, the battery
power will turn off automatically
to prevent the battery from
discharging.
ON Press the Engine Start/Stop button
while it is in the ACC position
without depressing the brake
pedal.
The warning lights can be checked
before the engine is started. Do not leave the Engine Start/Stop
button in the ON position when the
engine is not running to prevent
the battery from discharging.
START To start the engine, depress the
brake pedal and press the Engine
Start/ Stop button with the gear
shifted to the P (Park) or the N
(Neutral) position.
For your safety, start the engine
with the gear shifted to the P
(Park) position. If you press the Engine Start/Stop
button without depressing the
brake pedal, the engine does not
start and the Engine Start/Stop
button changes as follows:
2))
Ÿ$&&
Ÿ21
Ÿ2))
Information
To prevent vehicle battery discharge, the Engine Start/Stop button changes to the OFF
position when the Engine Start/Stop button is in the ACC or ON position with the gear in
P (Park) for a certain period of time. When the function operates, the tail lamps will turn
off. To use the tail lamps again, turn the headlight switch located on the steering column
to the OFF and ON position again.

06
6-11
NOTICE
To prevent damage to the vehicle:

[If the engine stalls while you are in
motion, do not attempt to shift the
gear to the P (Park) position.
If traffic and road conditions permit,
you may put the gear in N (Neutral)
while the vehicle is still moving and
press the Engine Start/Stop button in
an attempt to restart the engine.

[ Do not push or tow your vehicle to
start the vehicle.
NOTICE
To prevent damage to the vehicle:
Do not press the Engine Start/Stop
button for more than 10 seconds except
when the stop lamp fuse is blown.
When the stop lamp fuse is blown,
you cannot normally start the engine.
Replace the fuse with a new one. If you
are not able to replace the fuse, you
can start the engine by pressing and
holding the Engine Start/Stop button
for 10 seconds with the Engine Start/
Stop button in the ACC position.
For your safety always depress the
brake pedal before starting the vehicle.
Emergency Starting
B0248KO01
If the smart key battery is weak or the
smart key does not work correctly, you
can start the vehicle by pressing the
Engine Start/Stop button with the smart
key in the direction of the picture above.
Turning Off the Engine
1. Stop the vehicle and depress the
brake pedal fully.
2. Press the P button to shift to P (Park).
3. Press the Engine Start/Stop button to the OFF position and apply the
parking brake.

Driving Your Vehicle6-18
4. Press and hold the OK button A on
the steering wheel for more than 1
second.
5. When the message ‘Vehicle will stay in (N). Change gear to cancel’ appears
on the cluster LCD display, press the
ignition switch or Engine Start/Stop
button while depressing the brake
pedal.
If you wish to cancel, change gear to
P (Park), D (Drive) or R (Reverse), or N
(Neutral) will stay engaged when the
vehicle is Off.
Also, if you open the driver's door, the
gear will automatically shift to P (Park)
and the ignition switch or Engine
Start/Stop button will change to the
LOCK/OFF position.
NOTICE
With the gear in N (Neutral) the ignition
switch or Engine Start/Stop button
will be in the ACC position. In the ACC
position, the doors cannot be locked.
The battery may discharge if left in the
ACC position for a long time.
D (Drive)
This is the normal driving position.
The tr

ansmission will automatically shift
through an 8-gear sequence, providing
the best fuel economy and power.
For extra power when passing another
vehicle or driving uphill, depress the
accelerator pedal further until you feel
the transmission downshift to a lower
gear.
B0252EU08
To shift the gear D (Drive), press the D
button while depressing the brake pedal.
When the vehicle is stopped in the D
(Drive) position, if you open the driver's
door with the seat belt unfastened, the
gear will automatically shift to P (Park).
However, if the vehicle is in motion, the
gear may not automatically shift to P
(Park) to prevent automatic transmission
damage.
NOTICE
Always come to a complete stop before
shifting into D (Drive).
CAUTION
When you start after stopping on a
steep incline, even if the gear is in
D (Drive), if you do not depress the
accelerator or brake pedal, the vehicle
may roll backwards, which can cause an
accident.

06
6-19
When the battery is discharged
You cannot shift gears, when the battery
is discharged.
In emergencies, do the following to shift
the gear to N (Neutral) on a level ground.
1. Connect the battery cables from another vehicle or from a another
battery to the jump-starting terminals
inside the engine compartment.
For more details, refer to "Jump
Starting" section in chapter 8.
2. Release the Electronic Parking Brake with the ignition switch or Engine
Start/Stop button in the ON position.
3. Shift the gear to the N (Neutral) position. Refer to the “To stay in N
(Neutral) when vehicle is Off" in this
chapter.
Information
In situations when the gear needs to be
shifted from P (Park) to N (Neutral) when
the ignition switch or Engine Start/Stop
button is in the OFF position, refer to the
“To stay in N (Neutral) when vehicle is
OFF” in this chapter.
Shift-lock system
For your safety, the automatic
transmission has a shift-lock system
which prevents shifting the transmission
from P (Park) into R (Reverse) or D (Drive)
unless the brake pedal is depressed.
To shift from P (Park) or N (Neutral) into R
(Reverse) or D (Drive):
1. Depress and hold the brake pedal.
2. Start the engine.
3. Shift gear while depressing the brake pedal.
Ignition key interlock system (if
equipped)
The ignition key cannot be removed
unless the shift button is in the P (Park)
position.

06
6-23
Turn engine On to change gear (if
equipped)
B0253EU13
The message is displayed when the
engine is off or battery level is low.
Vehicle will stay in (N). Change gear
to cancel
B0253EU05
This message is displayed when pushing
the “OK” button on the steering wheel
after the message ‘Press and hold the
OK button on the steering wheel to stay
in Neutral’ appears on the cluster LCD
display. The gear stays in N(Neutral)
position after turning off the engine.
NEUTRAL engaged
B0253EU06
This message is displayed when the N
(Neutral) position is engaged.
Shift button held down
B0253EU08
When the shift button is pressed
continuously or the shift button does not
properly operate. Clean the surroundings
of gear shift button.
Immediately have the vehicle inspected
by an authorized HYUNDAI dealer.

06
6-29
Releasing the parking brake
B0260EU02
To release EPB (Electronic Parking
Brake):
1. Place the ignition switch or press the E
ngine Start/Stop button to the ON or
START position.
2. Press the EPB switch while depressing the brake pedal.
Make sure the Parking Brake warning
light goes off.
To release EPB (Electronic Parking Brake)
automatically:

[ Gear in P (P
ark)
With the engine running depress the
brake pedal and shift out of P (Park) to
R (Reverse) or D (Drive).

[ Gear in N (Neutral)
With the engine running depress
the brake pedal and shift out of N
(Neutral) to R (Reverse) or D (Drive).

[Satisfy the following conditions
1. Ensure seat belts are fastened and the doors, hood and liftgate are closed.
2. With the engine running, depress the brake pedal and shift out of P (Park) to
R (Reverse), D (Drive) or Manual shift
mode.
3. Depress the accelerator pedal. Make sure the Parking Brake warning
light goes off.
Information

[For your safety, you can engage EPB
even though the ignition switch is in the
LOCK/OFF position (only if battery
power is available), but you cannot
release it.

[ For your safety, depress the brake
pedal and release the parking brake
manually with the EPB switch when
you drive downhill or when backing up
the vehicle.
NOTICE

[If the Parking Brake warning light is
still on even though the EPB has been
released, have the system checked
by an authorized HYUNDAI dealer.

[ Do not drive your vehicle with EPB
applied. It may cause excessive brake
pad and brake rotor wear.

06
6-37
Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
do not attempt to modulate your brake
pressure and do not try to pump your
brakes. Depress your brake pedal as hard
as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your ABS is active.
ABS does not reduce the time or distance
it takes to stop the vehicle.
Always maintain a safe distance from the
vehicle in front of you.
ABS will not prevent a skid that results
from sudden changes in direction, such
as trying to take a corner too fast or
making a sudden lane change. Always
drive at a safe speed for the road and
weather conditions.
ABS cannot prevent a loss of stability.
Always steer moderately when braking
hard. Severe or sharp steering wheel
movement can still cause your vehicle to
veer into oncoming traffic or off the road.
On loose or uneven road surfaces,
operation of the anti-lock brake system
may result in a longer stopping distance
than for vehicles equipped with a
conventional brake system.
The ABS (
) warning light will stay on
for several seconds after the ignition
switch or Engine Start/Stop button is in
the ON position.
During that time, ABS will go through
self-diagnosis and the light will go off if
everything is normal. If the light stays on,
you may have a problem with your ABS.
Contact an authorized HYUNDAI dealer
as soon as possible.
WARNING
If the ABS () warning light is on and
stays on, you may have a problem with
the ABS. Your power brakes will work
normally. To reduce the risk of serious
injury or death, contact your authorized
HYUNDAI dealer as soon as possible.
NOTICE
When you drive on a road having poor
traction, such as an icy road, and apply
your brakes continuously, ABS will be
active continuously and the ABS (
)
warning light may illuminate. Pull your
vehicle over to a safe place and turn the
vehicle off.
Restart the vehicle. If the ABS warning
light is off, then your ABS system is
normal.
Otherwise, you may have a problem
with your ABS system. Contact an
authorized HYUNDAI dealer as soon as
possible.
Information
When you jump start your vehicle because
of a drained battery, the ABS ()
warning light may turn on at the same
time. This happens because of the low
battery voltage. It does not mean your
ABS is malfunctioning. Have the battery
recharged before driving the vehicle.