climate control HYUNDAI VELOSTER 2011 User Guide

4105
Features of your vehicle
✽NOTICE
• Replace the filter according to the
Maintenance Schedule.
If the vehicle is being driven in severe
conditions such as dusty, rough roads,
more frequent climate control air fil-
ter inspections and changes are
required.
• When the air flow rate suddenly
decreases, the system should be
checked by an authorized HYUNDAI
dealer.
Checking the amount of air con-
ditioner refrigerant and compres-
sor lubricant
When the amount of refrigerant is low,
the performance of the air conditioning is
reduced. Overfilling also has a negative
influence on the air conditioning system.
Therefore, if abnormal operation is
found, have the system inspected by an
authorized HYUNDAI dealer.
✽NOTICE
It is important that the correct type and
amount of oil and refrigerant is used.
Otherwise, damage to the compressor
and abnormal system operation may
occur.
WARNING
The air conditioning system should
be serviced by an authorized
HYUNDAI dealer. Improper service
may cause serious injury to the
person performing the service.
procarmanuals.com

Features of your vehicle
106 4
• For maximum defrosting, set the tem-
perature control to the extreme
right/hot position and the fan speed
control to the highest speed.
• If warm air to the floor is desired while
defrosting or defogging, set the mode
to the floor-defrost position.
• Before driving, clear all snow and ice
from the windshield, rear window, out-
side rear view mirrors, and all side win-
dows.
• Clear all snow and ice from the hood
and air inlet in the cowl grill to improve
heater and defroster efficiency and to
reduce the probability of fogging up
inside of the windshield.
Manual climate control system
To defog inside windshield
1. Select any fan speed except “0” posi-
tion.
2. Select desired temperature.
3. Select the or position.
4. The outside (fresh) air will be selected
automatically. Additionally, the air con-
ditioning will automatically operate if
the mode is selected to the posi-
tion.
If the air conditioning and outside (fresh)
air position are not selected automatical-
ly, press the corresponding button manu-
ally.
WINDSHIELD DEFROSTING AND DEFOGGING
WARNING- Windshield
heating
Do not use the or position
during cooling operation in
extremely humid weather. The dif-
ference between the temperature of
the outside air and that of the wind-
shield could cause the outer sur-
face of the windshield to fog up,
causing loss of visibility. In this
case, set the mode selection knob
or button to the position and
fan speed control knob or button to
lower speed.
OFS040110
procarmanuals.com

4107
Features of your vehicle
To defrost outside windshield
1. Set the fan speed to the highest
(extreme right) position.
2. Set the temperature to the extreme hot
position.
3. Select the position.
4. The outside (fresh) air and air condi-
tioning will be selected automatically.
If the air-conditioning, outside (fresh) air
position and higher fan speed are not
selected automatically, adjust the corre-
sponding button or knob manually.
Automatic climate control system
To defog inside windshield
1. Select desired fan speed.
2. Select desired temperature.
3. Press the defroster button ( ).
4. The air-conditioning will turn on
according to the detected ambient
temperature, outside (fresh) air posi-
tion and higher fan speed will be
selected automatically.
5. If blower fan speed is low, the blower
fan speed will be set middle speed
automatically.
If the air-conditioning, outside (fresh) air
position and higher fan speed are not
selected automatically, adjust the corre-
sponding button or knob manually.
If the position is selected, lower fan
speed is controlled to higher fan speed.
To defrost outside windshield
1. Set fan speed to the highest position.
2. Set temperature to the extreme hot
(HI) position.
3. Press the defroster button ( ).
4. The air-conditioning will turn on
according to the detected ambient
temperature and outside (fresh) air
position will be selected automatically.
5. If the air-conditioning, outside (fresh)
air position and higher fan speed are
not selected automatically, adjust the
corresponding button or knob manual-
ly.
If the position is selected, lower fan
speed is controlled to higher fan speed.
OFS040111OFS040112OFS040113
procarmanuals.com

Features of your vehicle
108 4
Defogging logic
To reduce the probability of fogging up
the inside of the windshield, the air intake
or air conditioning are controlled auto-
matically according to certain conditions
such as or position. To cancel or
return the defogging logic, do the follow-
ing.
Manual climate control system
1. Turn the ignition switch to the ON posi-
tion.
2. Select the defrost button ( ).
3. Press the air intake control button at
least 5 times within 3 seconds.
The indicator on the air intake button
blinks 3 times with 0.5 seconds of inter-
val. It indicates that the defogging logic is
canceled or returned to the programmed
status.
If the battery has been discharged or dis-
connected, it resets to the defog logic
status.
Automatic climate control system
1. Turn the ignition switch to the ON posi-
tion.
2. Press the defrost button ( ).
3. While holding the air conditioning
(A/C) button, press the air intake con-
trol button at least 5 times within 3 sec-
onds.
The A/C display blinks 3 times with 0.5
seconds of interval. It indicates that the
defogging logic is canceled or returned to
the programmed status.
If the battery has been discharged or dis-
connected, it resets to the defog logic
status.
OFS040114OFS040115
procarmanuals.com

Driving your vehicle
14 5
✽NOTICE
• You must reach a speed of at least 10
km/h since last idle stop.
• If you unfasten the seat belt or open
the driver’s door (engine hood) in
auto stop mode, the light on the ISG
OFF button will illuminate and ISG
system is deactivated. If your vehicle
is equipped with a supervision cluster,
the notice will illuminate on the LCD
display.
Turn the ignition switch to the START
position to start the engine manually.
Auto start
To restart the engine from idle stop
mode
• Press the clutch pedal when the shift
lever is in the N (Neutral) position.
The engine will start and the green AUTO
STOP indicator ( ) on the instrument
cluster will go out.
The engine will also restart automati-
cally without the driver’s any actions
if the following occurs:
- The fan speed of manual climate con-
trol system is set above the 3rd position
when the air conditioning is on.
- The fan speed of automatic climate
control system is set above the 6th
position when the air conditioning is on.
- When a certain amount of time has
passed with the climate control system
on.
- When the defroster is on.
- The brake vaccum pressure is low.
- The battery charging status is low.
- The vehicle speed exceeds 5 km/h.
OFS052033L
OFS052026L
OFS052054L
■Type A
■Type BOFS052029L
procarmanuals.com

7
Engine compartment / 7-2
Maintenance services / 7-3
Owner maintenance / 7-5
Scheduled maintenance service / 7-7
Explanation of scheduled maintenance items / 7-28
Engine oil / 7-32
Engine coolant / 7-33
Brake/clutch fluid / 7-36
Washer fluid / 7-37
Parking brake / 7-37
Air cleaner / 7-38
Climate control air filter / 7-39
Wiper blades / 7-41
Battery / 7-43
Tires and wheels / 7-46
Fuses / 7-56
Light bulbs / 7-66
Appearance care / 7-78
Emission control system / 7-84
Maintenance
procarmanuals.com

79
Maintenance
NORMAL MAINTENANCE SCHEDULE -FOR EUROPE (CONT.)
15,000 km (10,000 miles)/12months
❑ Add fuel additives *5
(Add every 15,000km (10,000miles) or 12 months)
❑ Replace engine oil and engine oil filter (MPI engine) *2 *3 *4
(Replace every 15,000km (10,000miles) or 12months
30,000 km (20,000 miles)/12months
❑ Inspect air cleaner filter
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect parking brake
❑ Inspect steering gear rack, linkage and boots
❑ Replace climate control air filter (if equipped)
❑ Replace engine oil and engine oil filter (GDI) *
2*3*4
(Replace every 30,000km (20,000 miles) or 12 months)
60,000 km (40,000 miles) /24months
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect cooling system
(At first, inspect at 60,000km (40,000 miles) or 48 months :
After that, inspect every 30,000km (20,000 miles) or 24
months)
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect double clutch transmission fluid (if equipped) *
9
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect Fuel filter *
7
❑ Inspect fuel lines, hoses and connections
❑ Inspect fuel tank air filter
❑ Inspect manual transaxle fluid (if equipped) *
9
❑ Inspect parking brake
❑ Inspect steering gear rack, linkage and boots
(Continued)
procarmanuals.com

Maintenance
10 7
NORMAL MAINTENANCE SCHEDULE -FOR EUROPE (CONT.)
90,000km (60,000 miles)/36months
❑ Inspect air cleaner filter
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect cooling system
(At first, inspect at 60,000km (40,000 miles) or 48 months :
After that, inspect every 30,000km (20,000 miles) or 24
months)
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect drive belts *
1
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect parking brake
❑ Inspect steering gear rack, linkage and boots
❑ Inspect valve clearance *
6
❑ Replace climate control air filter (if equipped)
❑ Replace engine oil and engine oil filter (GDI engine) *2 *3 *4
(Continued)
❑ Inspect vapor hose and fuel filler cap
❑ Replace air cleaner filter
❑ Replace climate control air filter (if equipped)
❑ Replace spark plugs (MPI engine)
❑ Replace engine oil and engine oil filter *
2*3*4
(Replace every 30,000km (20,000 miles) or 12 months)
procarmanuals.com

711
Maintenance
NORMAL MAINTENANCE SCHEDULE -FOR EUROPE (CONT.)
120,000km (80,000 miles)/48months
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect cooling system
(At first, inspect at 60,000km (40,000 miles) or 48 months :
After that, inspect every 30,000km (20,000 miles) or 24
months)
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect double clutch transmission fluid (if equipped) *
9
❑ Inspect drive belts *1
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect Fuel filter *
7
❑ Inspect fuel lines, hoses and connections
❑ Inspect fuel tank air filter
❑ Inspect manual transaxle fluid (if equipped) *
9
❑ Inspect parking brake
(Continued)
(Continued)
❑ Inspect steering gear rack, linkage and boots
❑ Inspect vapor hose and fuel filler cap
❑ Replace air cleaner filter
❑ Replace climate control air filter (if equipped)
❑ Replace engine oil and engine oil filter (GDI engine) *
2 *3 *4
❑ Replace spark plugs (MPI engine)
procarmanuals.com

Maintenance
12 7
NORMAL MAINTENANCE SCHEDULE -FOR EUROPE (CONT.)
150,000km (100,000 miles)/60months
❑ Inspect air cleaner filter
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect cooling system
(At first, inspect at 60,000km (40,000 miles) or 48 months :
After that, inspect every 30,000km (20,000 miles) or 24
months)
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect drive belts *
1
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect parking brake
❑ Inspect steering gear rack, linkage and boots
❑ Replace climate control air filter (if equipped)
❑ Replace engine oil and engine oil filter (GDI engine) *
2 *3 *4
180,000km (120,000 miles)/72months
❑ Inspect air conditioner compressor (if equipped)
❑ Inspect air conditioner refrigerant (if equipped)
❑ Inspect battery condition
❑ Inspect brake lines, hoses and connections
❑ Inspect brake pedal, clutch pedal (if equipped)
❑ Inspect brake/clutch fluid
❑ Inspect cooling system
(At first, inspect at 60,000km (40,000 miles) or 48 months :
After that, inspect every 30,000km (20,000 miles) or 24
months)
❑ Inspect disc brakes and pads (if equipped)
❑ Inspect double clutch transmission fluid (if equipped) *
9
❑ Inspect drive belts *1
❑ Inspect drive shaft and boots
❑ Inspect exhaust system
❑ Inspect front suspension ball joints
❑ Inspect Fuel filter *
7
❑ Inspect fuel lines, hoses and connections
❑ Inspect fuel tank air filter
❑ Inspect manual transaxle fluid (if equipped) *
9
❑ Inspect parking brake
(Continued)
procarmanuals.com