lock HYUNDAI VENUE 2021 Owners Manual

08
8-27
WARNING
Tire failure may cause loss of
vehicle control resulting in an
accident. To reduce risk of SERIOUS
INJURY or DEATH, take the
following precautions:

[Inspect your tires monthly for
proper inflation as well as wear
and damage.

[The recommended cold tire
pressure for your vehicle can be
found in this manual and on the
tire label located on the driver’s
side center pillar. Always use a
tire pressure gauge to measure
tire pressure. Tires with too
much or too little pressure wear
unevenly causing poor handling.

[Check the pressure of the
spare every time you check the
pressure of the other tires on
your vehicle.

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, or traction.

[ALWAYS replace tires with
the same type, size, brand,
construction and tread pattern
as each tire that was originally
supplied with this vehicle. Using
tires and wheels other than the
recommended sizes could cause
unusual handling characteristics,
poor vehicle control, or
negatively affect your vehicle’s
Anti-Lock Brake System (ABS)
resulting in a serious accident.
Tire Care
For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended
tire inflation pressures and stay
within the load limits and weight
distribution recommended for your
vehicle.
OQX089049N
All specifications (sizes and
pressures) can be found on a label
attached to the driver’s side center
pillar.
Recommended Cold Tire
Inflation Pressures
All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold tires” means the
vehicle has not been driven for at
least three hours or has been driven
for less than one mile (1.6 km).
Warm tires normally exceed
recommended cold tire pressures
by 4 to 6 psi (28 to 41 kPa). Do not
release air from warm tires to adjust
the pressure or the tires will be
under-inflated. For recommended
inflation pressure, refer to “Tire and
Wheels” in chapter 2.
TIRES AND WHEELS

Maintenance
8-30
Tire Replacement
Tread wear indicatorTread wear indicator
OLMB073027
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 2/32 inch (1.6 mm) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the tread surface to
become level with the tread wear
indicators before replacing the tire.
WARNING
To reduce the risk of DEATH or
SERIOUS INJURY:

[Replace tires that are worn, show
uneven wear, or are damaged.
Worn tires can cause loss of
braking effectiveness, steering
control, and traction.

[Always replace tires with the
same size as each tire that was
originally supplied with this
vehicle. Using tires and wheels
other than the recommended
sizes could cause unusual
handling characteristics, poor
vehicle control, or negatively
affect your vehicle’s Anti-Lock
Brake System (ABS) resulting in a
serious accident.

[Tires degrade over time, even
when they are not being used.
Regardless of the remaining
tread, HYUNDAI recommends
that tires be replaced after six (6)
years of normal service.

[When replacing tires, it is
recommended to replace the
two front or two rear tires as a
pair. Replacing just one tire can
seriously affect your vehicle’s
handling. If only replacing one
pair of tires, it is recommended
to install the pair of new tires on
the rear axle.

[Heat caused by hot climates or
frequent high loading conditions
can accelerate the aging process.
Failure to follow this warning
may cause sudden tire failure,
which could lead to a loss of
vehicle control resulting in an
accident.

Maintenance
8-40
Instrument Panel Fuse
Replacement
OQX089024L
1. Turn the engine off.
2. Turn all other switches OFF.
3. Open the fuse panel cover.
4. Refer to the label on the inside of
the fuse panel cover to locate the
suspected fuse location.
OQXI079022
5. Pull the suspected fuse straight out.
Use the removal tool provided in the
engine compartment fuse panel.
6. Check the removed fuse; replace it if
it is blown. Spare fuses are provided in
the instrument panel fuse panels (or in
the engine compartment fuse panel).7. Push in a new fuse of the same
rating, and make sure it fits tightly in
the clips. If it fits loosely, consult an
authorized HYUNDAI dealer.
In an emergency, if you do not have a
spare fuse, use a fuse of the same rating
from a circuit you may not need for
operating the vehicle.
If the headlamps or other electrical
components do not work and the fuses
are undamaged, check the fuse panel
in the engine compartment. If a fuse is
blown, it must be replaced with the same
rating.
Fuse switch
OQX089036L
Always, place the fuse switch to the ON
position.
If you move the switch to the OFF
position, some items such as the audio
system and digital clock must be reset
and the smart key may not work properly.

08
8-45
Driver’s side fuse panel
Fuse Name (A) Circuit Protected
S/HEATER 20A Front Seat Warmer Control Module
MODULE 1 7.5A Stop Lamp Switch, ATM Shift Lever
MEMORY 2 7.5A SRS Control Module
AIR BAG 10A Passenger Occupant Detection Sensor, SRS Control Module
DOOR LOCK 20A Tail Gate Relay, T/Turn Unlock Realy, Door Lock/Unlock Realy
ECU 6 10A ECM, PCM
DRL 10A DRL Relay
MODULE 6 10A Data Link Connector, Key Interlock Solenoid
T/SIGNAL LAMP 15A IBU
MODULE 2 10ACrash Pad Switch, Multifunction Camera Unit, Blind Spot
Collision Warning Unit LH/RH
SUNROOF 15A Sunroof Motor
MODULE 3 7.5AConsole Switch, ATM Shift Lever Indicator, A/C Control Module,
Audio, Front Seat Warmer Control Module

Maintenance
8-46
Driver’s side fuse panel
Fuse Name (A) Circuit Protected
WIPER RR 15A E/R Junction Block (Wiper RR Relay), Rear Wiper Motor
WASHER 15A Multifunction Switch
A/BAG IND 7.5A Center Facia Switch, Instrument Cluster
IBU 2 7.5A IBU
ABS3 7.5AE/R Junction Block (Multipurpose Check Connector), ESC
Module
WIPER FRT 25A E/R Junction Block (Wiper FRT Low Relay), Front Wiper Motor
A/C 2 7.5A E/R Junction Block (Blower Relay), A/C Control Module
HEATED
STEERING15A Not Used
CLUSTER 7.5A Instrument Cluster
MODULE 7 10APower Outlet Relay, Power Outside Mirror Switch, IBU, Audio,
A/V & Navigation Head Unit
MDPS 2 7.5A MDPS Unit
MODULE 5 10A IBU, Front Seat Warmer Control Module
MODULE 4 7.5A IBU
A/C 3 7.5A Blower Motor, A/C Control Module

Maintenance
8-48
Engine compartment fuse panel
Fuse Name (A) Circuit Protected
MULTI
FUSEALT 125AAlternator, Multi Fuse - MDPS 1, Fuse - Rear Heated,
Blower, ABS 1, ABS 2
MDPS 1 80A MDPS Unit
FUSEREAR
HEATED40A ICU Junction Block (Rear Heated Relay)
ABS 1 40A Multipurpose Check Connector, ESC Module
ABS 2 40A ESC Module
BLOWER 40A Blower Relay
WIPER 10A Wiper FRT LO Realy, IBU
ECU2 15A ECM/PCM
ECU4 15A ECM/PCM
ECU5 15A ECM/PCM
IGN COIL 20A Ignition Coil #1~#4
INJECTOR 15A ECM/PCM, Injector #1~#4, Fuel Pump Relay
PTC HEATER 50A PTC Heater Relay
B+3 50AICU Junction Block (Fuse - DOOR LOCK, S/HEATER,
SAFETY P/WINDOW, SUNROOF, Power Window Relay)
IG2 40A Start Relay, PDM Relay Box (IG2 Relay), Ignition Switch

08
8-49
Engine compartment fuse panel
Fuse Name (A) Circuit Protected
FUSECOOLING
FAN40A Cooling Fan 1/2 Relay
B+4 40AICU Junction Block (Fuse - MODULE 6, BRAKE
SWITCH, T/SIGNAL LAMP, DRL, IBU 1, Leak Current
Autocut Device)
ECU1 30A Main Relay, Fuse - ECU 4, ECU 5
A/C 1 10A A/C Relay
FUEL PUMP 20A Fuel Pump Relay
HORN 15A Horn Relay
B+2 30A ICU Junction Block (IPS (5CH) E-SWITCH, IPS (2CH))
IG1 30A[With Smart Key] PDM Relay Box (IG1 Relay)
[W/O Smart Key] Ignition Switch
POWER
OUTLET 140A ICU Junction Block (Power Outlet Relay)
B+1 30A ICU Junction Block (IPS (5CH) E-SWITCH, IPS (1CH))

Maintenance
8-50
Consult an authorized HYUNDAI dealer
to replace most vehicle light bulbs. It is
difficult to replace vehicle light bulbs
because other parts of the vehicle must
be removed before you can get to the
bulb. This is especially true for removing
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to the
vehicle.
Information
The headlamp and tail lamp lenses could
appear frosty if the vehicle is washed after
driving or the vehicle is driven at night
in wet weather. This condition is caused
by temperature difference between the
lamp inside and outside and, it does not
indicate a problem with your vehicle.
When moisture condenses in the lamp,
it will be removed after driving with the
headlamp on. The removable level may
differ depending on lamp size, lamp
position and environmental condition.
However, if moisture is not removed, we
recommend that your vehicle is inspected
by an authorized HYUNDAI dealer.
WARNING

[Prior to replacing a lamp, depress the
foot brake, move the shift lever into P
(Park) apply the parking brake, place
the ignition switch to the LOCK/OFF
position, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle and
to prevent possible electric shock.

[Be aware the bulbs may be hot and
may burn your fingers.
Headlamp, Parking lamp,
Daytime Running Light, Turn
signal lamp, Cornering lamp and
Side marker
Type A
OQX089014N
(1) Headlamp (High/Low)
(2) Parking lamp
(3) Turn signal lamp
(4) Side marker
Headlamp and parking lamp
WARNING
OQX089043

[Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.

[Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.
LIGHT BULBS

08
8-51

[Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.

[Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.

[A bulb should be operated only when
installed in a headlamp.

[If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
Headlamp and parking lamp
„Headlamp (high/low beam)
OQX089015L
„Parking lamp
OQX089016N
1. Open the hood.
2. Disconnect the negative battery
cable.
3. Remove the headlamp bulb cover by
turning it counterclockwise.
4. Disconnect the headlamp bulb
socket-connector.5. Remove the bulb from the headlamp
assembly.
6. Install a new headlamp bulb and snap
the headlamp bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
7. Connect the headlamp bulb socket-
connector.
8. Install the headlamp bulb cover by
turning it clockwise.
Information
The headlamp aiming should be adjusted
after an accident or after the headlamp
assembly is reinstalled at an authorized
HYUNDAI dealer.
OQX089017L
Turn signal lamp/side marker
1. Open the hood.
2. Disconnect the negative battery
cable.
3. Remove the socket (1) from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.

Maintenance
8-52
5. Install a new bulb by inserting it into
the socket and rotating it until it locks
into place.
6. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
7. Push the socket into the assembly and
turn the socket clockwise.
Type B, C
OQX089055N
(1) Cornering lamp
(2) Headlamp (Low/High)
(3) Daytime running lamp/parking lamp
(4) Turn signal lamp
(5) Side marker
Headlamp (bulb type)
WARNING
OQX089043

[Handle halogen bulbs with care.
Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass that could cause injuries if
broken.

[Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.

[Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.

[Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.

[A bulb should be operated only when
installed in a headlamp.

[If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.