headlamp HYUNDAI VENUE 2021 User Guide

Convenient Features
5-36
NOTICE

[Do not cover or spill anything on
the sensor (1) located in front of the
instrument panel.

[Do not clean the sensor using
a window cleaner, the cleanser
may leave a light film which could
interfere with sensor operation.

[If your vehicle has window tint or
other types of metallic coating on
the front windshield, the AUTO
headlamp system may not work
properly.
OIG046412
Parking lamp position ()
The parking lamp, license plate lamp and
instrument panel lamp are turned ON.
OIG046413
Headlamp position ()
The headlamp, parking lamp, license
plate lamp and instrument panel lamp
are turned ON.
Information
The ignition switch must be in the ON
position to turn on the headlamp.
High beam operation
OIG046415
To turn on the high beam headlamp,
push the lever away from you. The lever
will return to its original position.
The high beam indicator will light when
the headlamp high beams are switched
on.
To turn off the high beam headlamp, pull
the lever towards you. The low beams
will turn on.
WARNING
Do not use high beam when there are
other vehicles approaching you. Using
high beam could obstruct the other
driver’s vision.

05
5-37
OIG046414
To flash the high beam headlamp, pull
the lever towards you, then release the
lever. The high beams will remain ON as
long as you hold the lever towards you.
High Beam Assist (HBA) (if equipped)
OOS047409N
High Beam Assist (HBA) is a system that
automatically adjusts the headlamp
range (switches between high beam and
low beam) according to the brightness of
other vehicles and road conditions.
Operating condition
1. Place the headlamp switch in the
AUTO position.
2. Turn on the high beam by pushing the
lever away from you.
The High Beam Assist (
) indicator
will illuminate.
3. High Beam Assist system will turn on
when vehicle speed is above 25 mph
(40 km/h).

[If the headlamp switch is pushed
away when the High Beam Assist
system is operating, High Beam
Assist system will turn off and the
high beam will be on continuously.

[If the headlamp switch is pulled
towards you when the high beam
is OFF, the high beam will turn ON
without High Beam Assist system
canceled. When you let go of the
light switch, the lever will move to
the middle and the high beam will
turn OFF.

[If the headlamp switch is pulled
towards you when the high beam is
on by High Beam Assist system, the
low beam will be on and the High
Beam Assist system will turn OFF.

[If the headlamp switch is placed
to the headlamp ON position,
High Beam Assist system will turn
off and the low beam will be on
continuously.

Convenient Features
5-38
When High Beam Assist system is
operating, the high beam switches to low
beamif any of the following conditions
occur:
- When the headlamp of an on-coming
vehicle is detected.
- When the tail lamp of a vehicle in front
is detected.
- When the headlamp or tail lamp of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light is
bright enough that high beams are not
required.
- When streetlights or other lights are
detected.
- When the headlamp switch is not in
the AUTO position.
- When High Beam Assist system is off.
- When vehicle speed is below 22MPH
(35 km/h).
OIK047132N
Warning light and message
When High Beam Assist system is not
working properly, the Check High Beam
Assist warning message will come on
for a few second. After the message
disappears, the master warning light (
)
will illuminate. Take your vehicle to an
authorized HYUNDAI dealer and have the
system checked.
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an on-
coming vehicle or a vehicle in front is
dim. Such examples may include:

[When the headlamps of an on-
coming vehicle or the tail lamps of
a vehicle in front is covered with
dust, snow, or water.

[When the headlamps on an on-
coming vehicle are OFF, but the
fog lamps are ON.

05
5-39
2. When the High Beam Assist camera
is adversely affected by an external
condition. Such examples may
include:

[When the vehicle’s headlamps
have been damaged or not
repaired properly.

[When the vehicle headlamps are
not aimed properly.

[When the vehicle is driven on a
narrow curved road or rough road

[When the vehicle is driven on an
uphill road or downhill road

[When only part of the vehicle in
front is visible on a crossroad or
curved road.

[When there is a traffic light,
reflecting sign, flashing sign or
mirror.

[When the road conditions are bad
such as being wet or covered with
snow.

[When a vehicle suddenly appears
from a curve.

[When the vehicle is tilted from a
flat tire or being towed.

[When the Lane Keeping Assist
system warning light illuminates.

[When the light from the on-coming
or front vehicle is not detected
because of exhaust fume, smoke,
fog, snow, etc.

[When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged.
3. When the forward visibility is poor.
Such examples may include:

[When the headlamps of an on-
coming vehicle or a vehicle in front
is not detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.).

[When the windshield visibility is
poor. WARNING

[Do not attempt to disassemble
the front view camera without the
assistance of an authorized HYUNDAI
dealer technician. If the front camera
is removed for any reason, the
system may need to be re-calibrated.
Have the system inspected by an
authorized HYUNDAI dealer.

[If the windshield of your vehicle is
replaced, most likely the front view
camera will need to be re-calibrated.
If this occurs, have your vehicle
inspected and have the system re-
calibrated by an authorized HYUNDAI
dealer.

[Be careful that water doesn’t get into
High Beam Assist unit and do not
remove or damage related parts of
High Beam Assist system.

[Do not place objects on the crash
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.

[At times, High Beam Assist system
may not work properly. The system
is for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.

[When the system does not operate
normally, change the headlamp
position manually between the high
beam and low beam.

Convenient Features
5-40
Turn signals and lane change signals
OIG046417
To signal a turn, push down on the lever
for a left turn or up for a right turn in
position (A).
If an indicator stays on and does not flash
or if it flashes abnormally, one of the turn
signal bulbs may be burned out and will
require replacement.
Onetouch turn signal function
To activate the One Touch Turn Signal
function, push the turn signal lever up or
down to position (B) and then release it.
The lane change signals will blink 3, 5 or
7 times.
You can activate or deactivate the One
Touch Turn Signal function or choose
the number of blinks (3, 5, or 7) from the
User Settings mode in the LCD display.
For more information, refer to the “LCD
Display” section in this chapter.
Battery saver function
The purpose of this feature is to prevent
the battery from being discharged.
The system automatically turns off the
parking lamp when the driver turns the
vehicle off and opens the driver-side
door.
With this feature, the parking lamps will
turn off automatically if the driver parks
on the side of road at night.
If necessary, to keep the lamps on when
the vehicle is turned off, perform the
following:
(1) Open the driver-side door.
(2) Turn the parking lamps OFF and ON
again using the headlamp switch on
the steering column.
Headlamp delay function
If the key is removed from the ignition
switch or placed in the ACC position
or the LOCK/OFF position with the
headlamps ON, the headlamps (and/
or parking lamps) remain on for about
5 minutes. However, if the driver’s door
is opened and closed, the headlamps
are turned off after 15 seconds. Also,
with the engine off if the driver’s door is
opened and closed, the headlamps (and/
or parking lamps) are turned off after 15
seconds.
The headlamps (and/or parking lamps)
can be turned off by pressing the lock
button on the remote key or smart key
twice or turning the headlamp switch to
the OFF or AUTO position.
You can activate or deactivate the
Headlamp Delay function from the User
Settings Mode in the LCD display.
For more information, refer to the “LCD
Display” section in this chapter.

05
5-41
NOTICE
If the driver exits the vehicle through
another door besides the driver
door, the battery saver function
does not operate and the headlamp
delay function does not turn OFF
automatically.
This may cause the battery to
discharge. To avoid battery discharge,
turn OFF the headlamps manually from
the headlamp switch before exiting the
vehicle.
Interior Lights
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior lamp AUTO cut
The interior lamps will automatically go
off approximately 20 minutes after the
engine is turned off and the doors are
closed. If a door is opened, the lamp
will go off 40 minutes after the engine is
turned off. If the doors are locked by the
remote key or smart key and the vehicle
enters the armed stage of the theft
alarm system, the lamps will go off five
seconds later.
Front lamps
„Type A
OQX059041L
„Type B
OQX059023L
Front Map Lamp (1):
Press either lenses to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.

06
6-55
Detecting vehicles
The sensor may be limited when:

[The camera is blocked with a foreign
object or debris

[The camera lens is contaminated due
to tinted, filmed or coated windshield,
damaged glass, or stuck of foreign
matter (sticker, bug, etc.) on the glass

[Inclement weather such as heavy rain
or snow obscures the field of view of
the camera

[The camera sensor recognition is
limited

[The camera does not recognize the
entire vehicle in front.

[The camera is damaged.

[It is dark outside such as when the
headlamps are not on at night or the
vehicle is going through a tunnel.

[There is a shadow is on the road by a
median strip, trees, etc.

[The vehicle drives through a tollgate.

[The rear part of the vehicle in front is
not normally visible. (the vehicle turns
in other direction or the vehicle is
overturned.)

[The vehicle in front is too small to be
detected (for example a motorcycle or
a bicycle, etc.)

[The vehicle in front is an oversized
vehicle or trailer that is too big to be
detected by the camera recognition
system (for example a tractor trailer,
etc.)

[The camera's field of view is not well
illuminated (either too dark or too
much reflection or too much backlight
that obscures the field of view)
[The vehicle in front does not have
their rear lights properly turned ON or
their rear lights are unusually located.

[The outside brightness changes
suddenly, for example when entering
or exiting a tunnel

[When light coming from a street light
or an oncoming vehicle is reflected on
a wet road surface such as a puddle in
the road

[The field of view in front is obstructed
by sun glare

[The windshield glass is fogged up; a
clear view of the road is obstructed

[The vehicle in front is driving
erratically

[The vehicle is on unpaved or uneven
rough surfaces, or road with sudden
gradient changes.

[The vehicle drives inside a building,
such as a basement parking lot

[The adverse road conditions cause
excessive vehicle vibrations while
driving

[The sensor recognition changes
suddenly when passing over a speed
bump

[The vehicle in front is moving
vertically to the driving direction

[The vehicle in front is stopped
vertically

[The vehicle in front is driving towards
your vehicle or reversing

[You are on a roundabout and the
vehicle in front circles

06
6-77
When external condition is intervened

[The brightness outside changes
suddenly such as when entering or
exiting a tunnel or passing under a
bridge.

[The brightness outside is too low such
as when the headlamps are not on at
night or the vehicle is going through a
tunnel or passing under a bridge.

[There is a boundary structure in the
roadway such as a concrete barrier,
guardrail and reflector post that is
inadvertently being detected by the
camera.

[When light coming from a street light
or an oncoming vehicle is reflected on
a wet road surface such as a puddle in
the road.

[The field of view in front is obstructed
by sun glare.

[The lane suddenly disappears such as
at the intersection.

[There is not enough distance between
you and the vehicle in front to be able
to detect the lane line or the vehicle
ahead is driving on the lane line.

[Driving on a steep grade, over a hill, or
when driving on a curved road.

[The adverse road conditions cause
excessive vehicle vibrations while
driving.

[The surrounding of the inside rear
view mirror temperature is high due to
direct sunlight.
When front visibility is poor

[The windshield or the LKA system
camera lens is blocked with dirt or
debris.

[The windshield glass is fogged up; a
clear view of the road is obstructed.

[Placing objects on the dashboard, etc.LKA system Function Change
The driver can change LKA to Lane
Departure Warning system or change
LKA system mode between Standard LKA
and Active LKA from the LCD display. Go
WRWKH
8VHU6HWWLQJV

While Driving
6-86
Smooth Cornering
Avoid braking or gear changing in
corners, especially when roads are wet.
Ideally, corners should always be taken
under gentle acceleration.
Driving at Night
Night driving presents more hazards than
driving in the daylight. Here are some
important tips to remember:

[Slow down and keep more distance
between you and other vehicles, as it
may be more difficult to see at night,
especially in areas where there may
not be any street lights.

[Adjust your mirrors to reduce the glare
from other driver's headlamps.

[Keep your headlamps clean and
properly aimed. Dirty or improperly
aimed headlamps will make it much
more difficult to see at night.

[Avoid staring directly at the
headlamps of oncoming vehicles. You
could be temporarily blinded, and it
will take several seconds for your eyes
to readjust to the darkness.
Driving in the Rain
Rain and wet roads can make driving
dangerous. Here are a few things to
consider when driving in the rain or on
slick pavement:

[Slow down and allow extra following
distance. A heavy rainfall makes
it harder to see and increases the
distance needed to stop your vehicle.

[Turn OFF your Cruise Control.

[Replace your windshield wiper blades
when they show signs of streaking or
missing areas on the windshield.
[Tires should be properly maintained
with at least 2/32nds of an inch of
tread depth. If your tires do not have
enough tread, making a quick stop on
wet pavement can cause a skid and
possibly lead to an accident. See "Tire
Tread" in chapter 8.

[Turn on your headlamps to make it
easier for others to see you.

[Driving too fast through large puddles
can affect your brakes. If you must go
through puddles, try to drive through
them slowly.

[If you believe your brakes may be wet,
apply them lightly while driving until
normal braking operation returns.
Hydroplaning
If the road is wet enough and you are
going fast enough, your vehicle may
have little or no contact with the road
surface and actually ride on the water.
The best advice is SLOW DOWN when
the road is wet.
The risk of hydroplaning increases as
the depth of tire tread decreases, refer
to "Tire Tread" in chapter 8.
Driving in Flooded Areas
Avoid driving through flooded areas
unless you are sure the water is no
higher than the bottom of the wheel hub.
Drive through any water slowly. Allow
adequate stopping distance because
brake performance may be reduced.
After driving through water, dry the
brakes by gently applying them several
times while the vehicle is moving slowly.

8
Tires and Wheels ..............................................................................................8-27Tire Care ......................................................................................................................8-27
Recommended Cold Tire Inflation Pressures ........................................................... 8-27
Check Tire Inflation Pressure .....................................................................................8-28
Tire Rotation ...............................................................................................................8-29
Wheel Alignment and Tire Balance ...........................................................................8-29
Tire Replacement ...................................................................................................... 8-30
Wheel Replacement ................................................................................................... 8-31
Tire Traction ................................................................................................................ 8-31
Tire Maintenance........................................................................................................ 8-31
Tire Sidewall Labeling ................................................................................................ 8-31
Tire Terminology and Definitions ..............................................................................8-35
All Season Tires ........................................................................................................... 8-37
Summer Tires ............................................................................................................. 8-37
Snow Tires................................................................................................................... 8-37
Radial-Ply Tires .......................................................................................................... 8-38
Low Aspect Ratio Tires .............................................................................................. 8-38
Fuses ................................................................................................................ 8-39Instrument Panel Fuse Replacement ....................................................................... 8-40
Engine Compartment Panel Fuse Replacement ...................................................... 8-41
Fuse/Relay Panel Description................................................................................... 8-43
Light Bulbs ....................................................................................................... 8-50
Headlamp, Parking lamp, Daytime Running Light, Turn signal lamp,
Cornering lamp and Side marker ............................................................................. 8-50
Side Repeater Lamp Replacement .......................................................................... 8-54
Rear Combination Light Bulb Replacement .............................................................8-55
High Mounted Stop Lamp Replacement .................................................................. 8-57
License Plate Light Bulb Replacement ..................................................................... 8-57
Interior Light Bulb Replacement .............................................................................. 8-58
Appearance Care ............................................................................................ 8-59Exterior Care .............................................................................................................. 8-59
Interior Care ............................................................................................................... 8-63
Emission Control System ................................................................................ 8-65
Crankcase Emission Control System ....................................................................... 8-66
Evaporative Emission Control System
Including Onboard Refueling Vapor Recovery (ORVR) .......................................... 8-66
Exhaust Emission Control System ............................................................................ 8-66
California perchlorate notice .........................................................................8-68
Consumer Information ...................................................................................8-69
Reporting Safety Defects ............................................................................... 8-70