warning light HYUNDAI VENUE 2022 Repair Manual

06
6-27
WARNING
If ESC indicator light () or EPS
warning light () stays on or blinks,
your vehicle may have a malfunction
with the VSM system. When the
warning light illuminates, have your
vehicle checked by an authorized
HYUNDAI dealer as soon as possible.
Driving with wheels and tires with
different sizes may cause the ESC system
to malfunction. Before replacing tires,
make sure all four tires and wheels are
the same size. Never drive the vehicle
with different sized tires and wheels
installed.
Hill-Start Assist Control (HAC)
The Hill-Start Assist Control (HAC)
helps prevent the vehicle from rolling
backwards when starting a vehicle from
a stop on a hill. The system operates the
brakes automatically for approximately
2 seconds and releases the brake after 2
seconds or when the accelerator pedal is
depressed.
WARNING
Always be ready to depress the
accelerator pedal when starting off on
a incline. The HAC activates only for
approximately 2 seconds.
NOTICE

[The HAC does not operate when the
shift lever is in P (Park) or N (Neutral)

[The HAC activates even though the
ESC (Electronic Stability Control) is
off but does not activate when the
ESC has malfunctioned.
Good Braking Practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Move the shift lever into P (Park)
position, then apply the parking brake,
and place the ignition switch in the
LOCK/OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
is washed. Your vehicle will not stop as
quickly if the brakes are wet. Wet brakes
may cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal, taking care to keep the vehicle
under control at all times. If the braking
action does not return to normal, stop
as soon as it is safe to do so and call
an authorized HYUNDAI dealer for
assistance.
DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.

06
6-33
Warning and System Control
Blind-Spot Collision Warning system
„Left side
OQX069036L
„Right side
OQX069008L
First stage alert
If a vehicle is detected within the
boundary of the system, a yellow
warning light will illuminate on the outer
side view mirror.
If the detected vehicle is no longer within
the blind spot area, the warning will turn
off according to the driving conditions of
the vehicle.
„Left side
OQX069035L
„Right side
OQX069009L[A] : Warning sound
Second stage alert
A warning chime to alert the driver will
activate when:
1. A vehicle has been detected in the
blind spot area by the radar system
AND.
2. The turn signal is applied (same
side as where the vehicle is being
detected).
When this alert is activated, the warning
light on the outer side view mirror. Will
also blink. And a warning chime will
sound.
If you turn off the turn signal indicator,
the second stage alert will be
deactivated.
If the detected vehicle is no longer within
the blind spot area, the warning will turn
off according to the driving conditions of
the vehicle.

While Driving
6-34
WARNING

[The warning light on the outer side
view mirror will illuminate whenever
a vehicle is detected at the rear side
by the system.
To avoid accidents, do not focus only
on the warning light and neglect to
see the surroundings of the vehicle.

[Drive safely even though the vehicle
is equipped with Blind-Spot Collision
Warning system. Do not solely
rely on the system but check your
surroundings before changing lanes
or backing the vehicle up.

[The system may not alert the driver
in some situations due to system
limitations so always check your
surroundings while driving.
CAUTION

[Always pay attention to road and
traffic conditions while driving,
whether or not the warning light
on the outside rearview mirror
illuminates or there is a warning
alarm.

[Playing the vehicle audio system at
high volume may prevent occupants
from hearing Blind-Spot Collision
Warning system warning sounds.

[If any other warning sound such as
seat belt warning chime is already
generated, Blind-Spot Collision
Warning system warning may not
sound.
Detecting Sensor
OQX069011L
The rear corner radars are located inside
the rear bumper for detecting the side and
rear areas. Always keep the rear bumper
clean for proper operation of the system.
NOTICE

[The system may not work properly
when the bumper has been
damaged, or if the rear bumper has
been replaced or repaired.

[The sensing range differs somewhat
according to the width of the road.
When the road is narrow, the system
may detect other vehicles in the next
lane.

[The system may turn off if interfered
by electromagnetic waves.

[Always keep the sensors clean.

[NEVER disassemble the sensor
component or apply any impact on
the sensor component.

[Be careful not to apply unnecessary
force on the radar sensor or sensor
cover. If the sensor is forcibly moved
out of proper alignment, the system
may not operate correctly. In this
case, a warning message may not be
displayed. Have the vehicle inspected
by an authorized HYUNDAI dealer.

[Do not apply foreign objects such as
a bumper sticker or a bumper guard
near the radar sensor or apply paint
to the sensor area. Doing so may
adversely affect the performance of
the sensor.

06
6-35
Warning message
OIK057092L
Blind-Spot Collision Warning system
disabled. Radar blocked
This warning message may appear when:
- One or both of the sensors on the rear
bumper is blocked by dirt or snow or a
foreign object.
- Driving in rural areas where the sensor
does not detect another vehicle for an
extended period of time.
- When there is inclement weather such
as heavy snow or rain.
If any of these conditions occur, the light
on the BCW switch and the system will
turn off automatically.
When BCW canceled warning message
is displayed in the cluster, check to make
sure that the rear bumper is free from
any dirt or snow in the areas where the
sensor is located. Remove any dirt, snow,
or foreign material that could interfere
with the radar sensors.
After any dirt or debris is removed, the
system should operate normally after
about 10 minutes of driving the vehicle.
If the system still does not operate
normally have your vehicle inspected by
an authorized HYUNDAI dealer.
OAD058169L
Check Blind-Spot Collision Warning
system
If there is a problem with BCW system,
a warning message will appear and the
light on the switch will turn off. The
system will turn off automatically. Have
your vehicle inspected by an authorized
HYUNDAI dealer.

While Driving
6-42
Warning and system control
Rear Cross-Traffic Collision Warning
system
„Left
OQX069017L
„Right
OQX069016L
If the vehicle detected by the sensors
approaches from the rear left/right side
of your vehicle, the warning chime will
sound, the warning light on the outside
rearview mirror will blink and a message
will appear on the LCD display. If the
rear view monitor system is in activation,
a message will also appear on the
infotainment system screen.
The warning will stop when:
- The detected vehicle moves out of the
sensing area or
- when the vehicle is right behind your
vehicle or
- when the vehicle is not approaching
your vehicle or
- when the other vehicle slows down.
- The vehicle’s approaching speed is
decreased.
CAUTION

[When the operation condition of
Rear Cross-Traffic Collision Warning
system is satisfied, the warning
will occur every time a vehicle
approaches the side or rear of your
stopped (0 MPH vehicle speed)
vehicle.

[The system's warning may not
operate properly if the left or right of
your vehicle's rear bumper is blocked
by a vehicle or obstacle.

[Always pay attention to road and
traffic conditions while driving,
whether or not the warning light
on the outside rearview mirror
illuminates or there is a warning
alarm.

[Playing the vehicle audio system at
high volume may prevent occupants
from hearing the system's warning
sounds.

[If any other warning sound such as
seat belt warning chime is already
generated, Rear Cross-Traffic
Collision Warning system warning
may not sound.

While Driving
6-44
Warning message
OIK057092L
Blind-Spot Collision Warning system
disabled. Radar blocked
This warning message may appear when:
- One or both of the sensors on the rear
bumper is blocked by dirt or snow or a
foreign object.
- Driving in rural areas where the sensor
does not detect another vehicle for an
extended period of time.
- When there is inclement weather such
as heavy snow or rain.
If any of these conditions occur, the light
on BCW switch and the system will turn
off automatically.
When BCW canceled warning message
is displayed in the cluster, check to make
sure that the rear bumper is free from
any dirt or snow in the areas where the
sensor is located. Remove any dirt, snow,
or foreign material that could interfere
with the radar sensors.
After any dirt or debris is removed, the
system should operate normally after
about 10 minutes of driving the vehicle.
If the system still does not operate
normally have your vehicle inspected by
an authorized HYUNDAI dealer.
OAD058169L
Check Blind-Spot Collision Warning
system
If there is a problem with BCW system,
a warning message will appear and the
light on the switch will turn off. The
system will turn off automatically. RCCW
will not operate also if BCW system
turns off due to a malfunction. Have
your vehicle inspected by an authorized
HYUNDAI dealer.
Limitations of the system
The driver must be cautious in the below
situations because the system may not
detect other vehicles or objects in certain
circumstances:

[The vehicle is driven in inclement
weather such as heavy rain or snow.

[The sensor is polluted with rain, snow,
mud, etc.

[The rear bumper where the sensor
is located is covered with a foreign
object such as a bumper sticker, a
bumper guard, a bike rack, etc.

[The rear bumper is damaged, or the
sensor is out of the original default
position.

[The vehicle height gets lower or
higher due to heavy loading in a
liftgate, abnormal tire pressure, etc.

[When the temperature of the rear
bumper is high.

[When the sensors are blocked by
other vehicles, walls or parking-lot
pillars.

06
6-49
The warning light illuminates
on the LCD display, when you
cancel FCA system.
The driver can monitor FCA ON/OFF
status on the LCD display. Also, the
warning light illuminates when the ESC
(Electronic Stability Control) is turned
off. If the warning light remains ON
when FCA is activated, we recommend
that you have the system checked by an
authorized HYUNDAI dealer.
OQX069078N

[Setting Warning Timing
The driver can select the initial
warning activation time on the LCD
display.
*RWRWKH
S8VHU6HWWLQJV

While Driving
6-50
Prerequisite for activation
Prerequisite for activation FCA gets ready
to be activated, when ‘Active Assist’ or
‘Warning Only’ under Forward Safety is
selected in on the LCD display, and when
the following prerequisites are satisfied.
- The ESC (Electronic Stability Control)
is on.
- Vehicle speed is over 6 MPH (10
km/h).
- The system detects a vehicle in front,
which may collide with your vehicle.
(FCA may not be activated or may
sound a warning alarm in accordance
with the driving situation or vehicle
condition.)
WARNING

[Completely stop the vehicle on a safe
location before operating the switch
on the steering wheel to activate/
deactivate FCA system.

[FCA automatically activates upon
placing the POWER button to the ON
position. The driver can deactivate
FCA by canceling the system setting
on the LCD display.

[FCA automatically deactivates
upon canceling the ESC (Electronic
Stability Control). When the ESC is
canceled, FCA cannot be activated
on the LCD display. FCA warning light
will illuminate which is normal.
FCA Warning Message and
System Control
FCA produces warning messages and
warning alarms in accordance with
the collision risk levels, such as abrupt
stopping of the vehicle in front or
insufficient braking distance. Also, it
controls the brakes in accordance with
the collision risk levels.
Collision Warning (First warning)
OQX059029L
This warning message appears on the
LCD display with a warning chime.
Additionally, some vehicle system
intervention occurs by the engine
management system to help decelerate
the vehicle.
- Your vehicle speed may decelerate
moderately.
- FCA system has limited controls of
the brakes to preemptively mitigate
impact in a collision.
- If you select ‘Warning only’, FCA
system activates and produces only
warning alarms in accordance with
the collision risk levels. You should
control the brake directly because
FCA system does not control the
brake.

While Driving
6-52
FCA Sensor
„Front camera
OQX059031L
In order for FCA system to operate
properly, always make sure the front
view camera is clean and free of dirt,
snow, and debris. Dirt, snow, or foreign
substances on the surface may adversely
affect the sensing performance of the
camera.
NOTICE

[Always keep the front view camera
sensor clean and free of dirt and
debris.

[Be careful not to apply unnecessary
force on the front view camera
sensor. If the sensor is forcibly
moved out of proper alignment, FCA
system may not operate correctly.
In this case, a warning message may
not be displayed. Have the vehicle
inspected by an authorized HYUNDAI
dealer.

[Use only genuine HYUNDAI parts to
repair or replace a damaged sensor.
NOTICE

[NEVER install any accessories or
stickers on the front windshield, nor
tint the front windshield.

[NEVER locate any reflective objects
(i.e. white paper, mirror) over the
dashboard. Any light reflection may
cause a malfunction of the system.

[Pay extreme caution to keep the
camera out of water.

[NEVER disassemble the camera
assembly, nor apply any impact on
the camera assembly.
If the sensor is forcibly moved out
of proper alignment, FCA system
may not operate correctly. In this
case, a warning message may not
be displayed. Have the vehicle be
inspected by an authorized HYUNDAI
dealer.

[Playing the vehicle audio system at
high volume may offset the system
warning sounds.
Information
Have the system checked by an authorized
HYUNDAI dealer when:

[The windshield glass is replaced.

[The front view camera or related parts
are repaired or removed.

06
6-53
Warning message and warning light
OQX069054L
Forward Collision-Avoidance Assist (FCA)
system disabled. Camera obscured
When the sensor is contaminated due
to external environment such as snow,
rain or foreign substances, FCA system
operation may stop temporarily. If this
occurs, a warning message will appear
on the LCD display. In order for FCA
system to operate properly, remove
any dirt, snow or debris and clean the
camera sensor cover before the system
operation.
FCA may not properly operate in an area
(e.g. open terrain), where any substances
are not detected after turning ON the
engine.
WARNING
Depending on the driving, traffic, road
or weather condition, FCA system
may not activate properly without the
warning message displayed.
System Malfunction
OQX069053L
Check Forward Collision-Avoidance Assist
system

[When FCA is not working properly,
FCA warning light () will illuminate
and the warning message will appear
for a few seconds. After the message
disappears, the master warning light
(
) will illuminate. In this case, have
the vehicle inspected by an authorized
HYUNDAI dealer.

[FCA warning message may appear
along with the illumination of the
ESC (Electronic Stability Control)
warning light and FCA is automatically
deactivated.
WARNING

[FCA is only a supplemental system
for the driver's convenience. The
driver should hold the responsibility
to control the vehicle operation. Do
not solely depend on FCA system.
Rather, maintain a safe braking
distance, and, if necessary, depress
the brake pedal to reduce the driving
speed.

[In certain instances and under
certain driving conditions, FCA
system may activate unintentionally.
This initial warning message appears
on the LCD display with a warning
chime.