fuel filter HYUNDAI VENUE 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: VENUE, Model: HYUNDAI VENUE 2023Pages: 390, PDF Size: 5.37 MB
Page 24 of 390

02
2-11
RECOMMENDED LUBRICANTS AND CAPACITIES
To help achieve proper engine and powertrain performance and durability, use only
lubricants of the proper quality. The correct lubricants also help promote engine
efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
LubricantVolumeClassification
Engine oil
*1 *2
(drain and refill)
Smartstream G1.6 4.02 US qt. (3.8 b) API SN PLUS/SP or ILSAC GF-6
Manual transmission fluid 1.59 ~ 1.69 US qt.
(1.5 ~ 1.6 b) HK SYN MTF 70W (SK)
SPIRAX S6 GHME 70W MTF
(H.K.SHELL)
GS MTF HD 70W (GS CALTEX)
API GL-4, SAE 70W, TGO-9
Intelligent variable transmission
fluid 6.34 US qt. (6.7 b) CVTF (SP-CVT1)
*3
CoolantM/T 5.94 US qt. (5.62 b)
Mixture of antifreeze and water
(Phosphate-based Ethylene glycol
coolant for aluminum radiator)
IVT 6.32 US qt. (5.78 b)
Brake/clutch fluid 0.74 ~ 0.85 US qt.
(0.7 ~ 0.8 b) SAE J1704 DOT-4 LV, FMVSS 116
DOT-4, ISO4925 CLASS-6
Fuel 11.89 US gal. (45 b)Refer to “Fuel requirements” in
chapter 1.
M/T: Manual transmission
IVT: Intelligent variable transmission
*1 : Refer to the recommended SAE viscosity numbers on page 12.
*2 : Requires
If a lower grade engine oil (mineral oil including Semi-synthetic) is used, then the engine
oil and engine oil filter must be replaced as indicated severe maintenance condition.
*3 : Use only specified genuine Intelligent variable transmission fluid. The use of non-
specified fluid (even marked as compatible with genuine) could result in shift quality
deterioration and vibrations, eventually, the transmission failure.
Page 25 of 390

Vehicle Information2-12
Recommended SAE Viscosity
Number
CAUTION
Always be sure to clean the area around
any filler plug, drain plug, or dipstick
before checking or draining any
lubricant. This is especially important
in dusty or sandy areas and when the
vehicle is used on unpaved roads.
Cleaning the plug and dipstick areas
will prevent dirt and grit from entering
the engine and other mechanisms that
could be damaged. Engine oil viscosity (thickness) has an
effect on fuel economy and cold weather
operating (engine start and engine oil
flowability). Lower viscosity engine oils
can provide better fuel economy and
cold weather performance, however,
higher viscosity engine oils are required
for satisfactory lubrication in hot
weather.
Using oils of any viscosity other than
those recommended could result in
engine damage.
When choosing an oil, consider the
range of temperature your vehicle will be
operated in before the next oil change.
Proceed to select the recommended oil
viscosity from the chart.
Temperature Range for SAE Viscosity Numbers
Temperature °C -30 -20 -10 0 10 20 30 40 50
(°F) -10 0 20 40 60 80 100 120
Engine Oil
0W-20*Î 0W-20*Î
*1 : Requires
If a lower grade engine oil (mineral oil including Semi-synthetic) is used, then the engine
oil and engine oil filter must be replaced as indicated severe maintenance condition.
An engine oil displaying this API Certification Mark conforms to
the international Lubricant Specification Advisory Committee
(ILSAC). It is recommended to only use engine oils that uphold
this API Certification Mark.
Page 316 of 390

Maintenance8-8
Normal Maintenance Schedule
MAINTENANCE INTERVALS
MAINTENANCE
ITEM Months 12 24 36 48 60 72 84 96 108 120 132 144 156
Miles×1,000 8 16 24 32 40 48 56 64 72 80 88 96 104 Km×1,000 13 26 39 52 65 78 91 104 117 130 143 156 169
Engine oil and engine oil filter
*1
RRRRRRRRRRRRR
Fuel additives
*2
Add fuel additives every 8,000 miles (13,000 km) or 12 months
Air cleaner filter IIIRIIIRIIIRI
Spark plugs Replace every 96,000 miles (156,000 km) or 144 months
Tires Rotate tires every 8,000 miles (13,000 km)
Climate control air filter
(for evaporator and blower unit) Replace every 8,000 miles (13,000 km) or 12 months
Engine coolant At first, replace at 120,000 miles (200,000 km) or 10 years.
Thereafter, replace every 24,000 miles (39,000 km) or 36 months
Vacuum hose IIIIIIIIIIIII
Battery condition IIIIIIIIIIIII
Drive belts
*3
At first, inspect at 48,000 miles (78,000 km) or 72 months.
Thereafter, inspect every 8,000 miles (13,000 km) or 12 months
I : Inspect and if necessary, adjust, correct, clean or replace.
R : Replace or change.*1 :
Requires API SN PLUS (or above) grade engine oil. If a lower grade engine oil is used, then the engine oil and engine oil filter
must be replaced at every 5,000 miles (8,000 km) or 6 months as indicated for severe maintenance condition.
*2 :
If TOP TIER Detergent Gasoline is not available, one bottle of additive is recommended. Additives are available from your
authorized HYUNDAI dealer along with information on how to use them. Do not mix other additives.
*3 :
The drive belt should be replaced when cracks occur or tension is reduced excessively.
Page 318 of 390

Maintenance8-10
Normal Maintenance Schedule (CONT)
MAINTENANCE INTERVALS
MAINTENANCE
ITEM Months 12 24 36 48 60 72 84 96 108 120 132 144 156
Miles×1,000 8 16 24 32 40 48 56 64 72 80 88 96 104 Km×1,000 13 26 39 52 65 78 91 104 117 130 143 156 169
Vapor hose, fuel filler cap and fuel tank IIIIII
Fuel tank air filter
*4
IIIIII
Fuel filter
*4
IIIIII
Fuel lines, hoses and connections III
Parking brake IIIIII
Brake fluid Inspect every 8,000 miles (13,000 km) or 12 months,
Replace every 60,000 miles (96,000 km) or 48 months
I : Inspect and if necessary, adjust, correct, clean or replace.
R : Replace or change.*4 : Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this
maintenance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging,
loss of power, hard starting problem, etc. replace the fuel filter immediately regardless of maintenance schedule and consult an
authorized HYUNDAI dealer for details.
Page 320 of 390

Maintenance8-12
Engine Oil and Filter
The engine oil and filter should be
changed at the intervals specified in the
maintenance schedule. If the vehicle
is being driven in severe conditions,
more frequent oil and filter changes are
required.
Drive Belts
Inspect all drive belts for evidence
of cuts, cracks, excessive wear or oil
saturation and replace if necessary. Drive
belts should be checked periodically
for proper tension and adjusted as
necessary.
Fuel Filter
A clogged-up fuel filter may limit the
vehicle driving speed, damage the
emission system, and cause the hard
starting. When a considerable amount
of foreign substances are accumulated
in the fuel tank, the fuel filter should be
replaced.
Upon installing a new fuel filter, operate
the engine for several minutes, and
check the connections for any leakages.
Fuel filters should be installed by an
authorized HYUNDAI dealer.
Fuel Lines, Fuel Hoses and
Connections
Check the fuel lines, fuel hoses and
connections for leakage and damage.
Have an authorized HYUNDAI dealer
replace any damaged or leaking parts
immediately.
Vapor Hose and Fuel Filler Cap
The vapor hose and fuel filler cap should
be inspected at those intervals specified
in the maintenance schedule. Make sure
a new vapor hose or fuel filler cap is
correctly replaced.
Vacuum Crankcase Ventilation
Hoses (if equipped)
Inspect the surface of hoses for evidence
of heat and/or mechanical damage.
Hard and brittle rubber, cracking,
tears, cuts, abrasions, and excessive
swelling indicate deterioration. Particular
attention should be paid to examine
those hose surfaces nearest to high heat
sources, such as the exhaust manifold.
Inspect the hose routing to ensure that
the hoses do not come in contact with
any heat source, sharp edges or moving
component which might cause heat
damage or mechanical wear. Inspect
all hose connections, such as clamps
and couplings, to make sure they are
secure, and that no leaks are present.
Hoses should be replaced immediately if
there is any evidence of deterioration or
damage.
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
Page 374 of 390

Maintenance8-66
1. Crankcase Emission Control System
The positive crankcase ventilation system
is employed to prevent air pollution
caused by blow-by gases being emitted
from the crankcase. This system supplies
fresh filtered air to the crankcase through
the air intake hose. Inside the crankcase,
the fresh air mixes with blow-by gases,
which then pass through the PCV valve
into the induction system.
2. Evaporative Emission Control System Including Onboard
Refueling Vapor Recovery
(ORVR)
The Evaporative Emission Control System
is designed to prevent fuel vapors from
escaping into the atmosphere. The
ORVR system is designed to allow the
vapors from the fuel tank to be loaded
into a canister while refueling at the gas
station, preventing the escape of fuel
vapors into the atmosphere.
Canister
Fuel vapors generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in the
canister are drawn into the surge tank
through the purge control solenoid valve.
Purge Control Solenoid Valve (PCSV)
The purge control solenoid valve
is controlled by the Engine Control
Module (ECM); when the engine coolant
temperature is low during idling, the
PCSV closes so that evaporated fuel
is not taken into the engine. After the
engine warms-up during ordinary
driving, the PCSV opens to introduce
evaporated fuel to the engine.
3. Exhaust Emission Control System
The Exhaust Emission Control System is
a highly effective system which controls
exhaust emissions while maintaining
good vehicle performance.
When the engine starts or fails to start,
excessive attempts to restart the engine
may cause damage to the emission
system.
Engine Exhaust (carbon Monoxide)
Precautions
[ Carbon monoxide can be present
with other exhaust fumes. If you smell
exhaust fumes of any kind in your
vehicle, drive with all the windows
fully open. Have your vehicle checked
and repaired immediately.
WARNING
Engine exhaust gases contain carbon
monoxide (CO). Though colorless and
odorless, it is dangerous and could be
lethal if inhaled. Follow the instructions
on this page to avoid CO poisoning.
WARNING
CALIFORNIA PROPOSITION 65
WARNING
Engine exhaust and a wide variety of
automobile components and parts,
including components found in the
interior furnishings in a vehicle, contain
or emit chemicals known to the State
of California to cause cancer and
birth defects and reproductive harm.
In addition, certain fluids contained
in vehicles and certain products of
component wear contain or emit
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
Page 382 of 390

IndexI-4
Door Locks ........................................................................\
.................................. 5-12 Automatic Door Lock and Unlock Features ................................................... 5-15
Child-Protector Rear Door Locks ................................................................... 5-15
Operating Door Locks from Inside the Vehicle .............................................. 5-13
Operating Door Locks from Outside the Vehicle ............................................ 5-12
Drive Mode Integrated Control System ............................................................... 6-28
LCD Display Message ........................................................................\
............ 6-30
Driver Attention Warning (DAW) ....................................................................... 6-78
Leading Vehicle Departure Alert ..................................................................... 6-81
Resetting the System ........................................................................\
............... 6-79
System Malfunction ........................................................................\
................ 6-79
System Setting and Activation ........................................................................\
6-78
System Standby ........................................................................\
....................... 6-79
E
Emission Control System ........................................................................\
............ 8-65 Crankcase Emission Control System .............................................................. 8-66
Evaporative Emission Control System Including Onboard Refueling Vapor
Recovery (ORVR) ........................................................................\
................... 8-66
Exhaust Emission Control System .................................................................. 8-66
Engine .................................................................\
................................................... 2-7
Engine Compartment ........................................................................\
..................... 8-3
Engine Compartment ........................................................................\
..................... 2-6
Engine Coolant ........................................................................\
............................ 8-16 Changing Engine Coolant ........................................................................\
....... 8-18
Checking the Engine Coolant Level ............................................................... 8-16
Engine Number ........................................................................\
............................ 2-14
Engine Oil ........................................................................\
.................................... 8-15 Checking the Engine Oil and Filter ................................................................. 8-15
Checking the Engine Oil Level ....................................................................... 8-15
Explanation of Scheduled Maintenance Items .................................................... 8-12 Air Cleaner Filter ........................................................................\
.................... 8-13
Air Conditioning Refrigerant ........................................................................\
.. 8-14
Brake/Clutch Fluid ........................................................................\
.................. 8-14
Brake Discs, Pads, Calipers and Rotors .......................................................... 8-14
Brake Hoses and Lines ........................................................................\
............ 8-13
Cooling System ........................................................................\
....................... 8-13
Drive Belts ........................................................................\
.............................. 8-12
Page 383 of 390

I
I-5
Drive Shafts and Boots........................................................................\
............ 8-14
Engine Coolant ........................................................................\
........................ 8-13
Engine Oil and Filter ........................................................................\
............... 8-12
Exhaust Pipe and Muffler ........................................................................\
........ 8-14
Fuel Filter ........................................................................\
................................ 8-12
Fuel Lines, Fuel Hoses and Connections ........................................................ 8-12
Intelligent Variable Transmission (IVT) Fluid ................................................ 8-13
Manual Transmission Fluid ........................................................................\
..... 8-13
Parking Brake ........................................................................\
.......................... 8-14
Spark Plugs........................................................................\
.............................. 8-13
Steering Gear Box, Linkage & Boots/Lower Arm Ball Joint ......................... 8-14
Suspension Mounting Bolts ........................................................................\
.... 8-14
Vacuum Crankcase Ventilation Hoses ............................................................. 8-12
Vapor Hose and Fuel Filler Cap ...................................................................... 8-12
Exterior Features ........................................................................\
.......................... 5-75 Roof Side Rails ........................................................................\
....................... 5-75
Exterior Features ........................................................................\
.......................... 5-31
Fuel Filler Door ........................................................................\
....................... 5-34
Hood ...................................................................\
............................................. 5-31
Liftgate ...............................................................\
............................................. 5-32
Exterior Overview ........................................................................\
......................... 2-2
F
Forward Collision-Avoidance Assist (FCA) System ........................................... 6-48 FCA Sensor ........................................................................\
............................. 6-52
FCA Warning Message and System Control ................................................... 6-50
Limitations of the System ........................................................................\
....... 6-54
System Malfunction ........................................................................\
................ 6-53
System Setting and Activation ........................................................................\
6-48
Forward Collision-Avoidance Assist (FCA) System-Sensor Fusion ................... 6-59 FCA Sensor ........................................................................\
............................. 6-63
FCA Warning Message and System Control ................................................... 6-61
Limitations of the System ........................................................................\
....... 6-66
System Malfunction ........................................................................\
................ 6-65
System Setting and Activation ........................................................................\
6-59
Fuel Requirements ........................................................................\
......................... 1-5