tires INFINITI FX 2010 Service Manual

WHEELS AND TIRES
Road wheel
TypeSize Offset in (mm)
Conventional 18 × 8J 1.97 (50)
20 × 8J*1
21 × 9-1/2J
Spare 18 × 4-1/2T 1.18 (30)/0.98 (25)*2
*1: Option
*2: Aluminum
Tire
Type Size Pressure PSI (kPa) [Cold]
Conventional P265/60R18 33 (230)
P265/50R20*
P265/45R21
265/45R21
Spare (T-type) T175/90D18 60 (420)
*: Option
Technical and consumer information9-9
—
—
08/11/09—debbie


Steps for determining correct load
limit
1.Locate the statement “The combined
weight of occupants and cargo should
never exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2.Determine the combined weight of
the driver and passengers that will be
riding in your vehicle.
3.Subtract the combined weight of the
driver and passengers from XXX kg or
XXX lbs.
4.The resulting figure equals the avail-
able amount of cargo and luggage
load capacity. For example, if the XXX
amount equals 1400 lbs. and there
will be five 150 lb. passengers in your
vehicle, the amount of available
cargo and luggage load capacity is
650 lbs. (1400 750 (5 x 150) = 650
lbs) or (640 340 (5 x 70) = 300 kg.)
5.Determine the combined weight of
luggage and cargo being loaded on
the vehicle. That weight may not
safely exceed the available cargo and
luggage load capacity calculated in
Step 4.
6.If your vehicle will be towing a trailer,
load from your trailer will be trans-
ferred to your vehicle. Consult this
manual to determine how this re-
duces the available cargo and lug-
gage load capacity of your vehicle.
Before driving a loaded vehicle, confirm
that you do not exceed the Gross Vehicle
Weight Rating (GVWR) or the Gross Axle
Weight Rating (GAWR) for your vehicle.
(See “MEASUREMENT OF WEIGHTS” later
in this section.)
Also check tires for proper inflation pres-
sures. See the Tire and Loading Informa-
tion label.
SECURING THE LOAD
There are tie down hooks located in the cargo
area as shown. The tie down hooks can be used
to secure cargo with ropes or other types of
straps.
Do not apply a total load of more than 22 lb.
(98 N) to a single hook when securing cargo.
WARNING
● Properly secure all cargo with ropes or
straps to help prevent it from sliding or shift-
ing. Do not place cargo higher than the seat-
backs. In a sudden stop or collision, unse-
cured cargo could cause personal injury.
SIC3849
Technical and consumer information9-17
—
—
08/03/09—tbrooks


●The child restraint top tether strap may be
damaged by contact with items in the cargo
area. Secure any items in the cargo area.
Your child could be seriously injured or killed
in a collision if the top tether strap is
damaged.
● Do not load your vehicle any heavier than the
GVWR or the maximum front and rear
GAWRs. If you do, parts of your vehicle can
break, tire damage could occur, or it can
change the way your vehicle handles. This
could result in loss of control and cause per-
sonal injury.
LOADING TIPS
●The GVW must not exceed GVWR or
GAWR as specified on the
F.M.V.S.S./C.M.V.S.S. certification la-
bel.
●Do not load the front and rear axle to
the GAWR. Doing so will exceed the
GVWR.
WARNING
●Properly secure all cargo to help pre-
vent it from sliding or shifting. Do not
place cargo higher than the seat-
backs. In a sudden stop or collision,
unsecured cargo could cause per-
sonal injury.
●Do not load your vehicle any heavier
than the GVWR or the maximum front
and rear GAWRs. If you do, parts of
your vehicle can break, tire damage
could occur, or it can change the way
your vehicle handles. This could re-
sult in loss of control and cause per-
sonal injury.
●Overloading could not only shorten
the life of your vehicle and the tires,
but also could lead to hazardous ve-
hicle handling and long braking dis-
tance. This may cause a premature
tire malfunction, which could result in
a serious accident and personal in-
jury. Failures caused by overloading
are not covered by the vehicle’s
warranty.
9-18
Technical and consumer information
—
—
08/03/09—tbrooks


●The diameter of the threaded shank of the
hitch ball must be matched to the ball mount
hole diameter. The hitch ball shank should
be no more than 1/16 smaller than the hole
in the ball mount.
● The threaded shank of the hitch ball must be
long enough to be properly secured to the
ball mount. There should be at least 2
threads showing beyond the lock washer
and nut.
Sway control device
Sudden maneuvers, wind gusts and buffeting
caused by other vehicles can affect trailer han-
dling. Sway control devices may be used to help
control these affects. If you choose to use one,
contact a reputable trailer hitch supplier to
make sure the sway control device will work
with the vehicle, hitch, trailer and the trailer’s
brake system. Follow the instructions provided
by the manufacturer for installing and using the
sway control device.
Class I hitch
Class I trailer hitch equipment (receiver, ball
mount and hitch ball) can be used to tow
trailers of a maximum weight of 2,000 lb
(907 kg).
Class II hitch
Class II trailer hitch equipment (receiver, ball
mount and hitch ball) can be used to tow
trailers of a maximum weight of 3,500 lb
(1,588 kg).
CAUTION
● Special hitches which include frame rein-
forcements are required for towing above
2,000 lb (907 kg). Suitable genuine INFINITI
hitches for pickup trucks and sport utility
vehicles are available at an INFINITI retailer.
● The hitch should not be attached to or affect
the operation of the impact-absorbing
bumper.
● Do not use axle-mounted hitches.
● Do not modify the vehicle exhaust system,
brake system, etc. to install a trailer hitch.
● To reduce the possibility of additional dam-
age if your vehicle is struck from the rear,
where practical, remove the hitch and/or re-
ceiver when not in use. After the hitch is
removed, seal the bolt holes to prevent ex-
haust fumes, water or dust from entering the
passenger compartment.
● Regularly check that all trailer hitch mount-
ing bolts are securely mounted.
Tire pressures
●When towing a trailer, inflate the ve-
hicle tires to the recommended cold
tire pressure indicated on the Tire and
Loading Information label.
●Trailer tire condition, size, load rating
and proper inflation pressure should
be in accordance with the trailer and
tire manufacturers’ specifications.
Safety chains
Always use a suitable chain between your ve-
hicle and the trailer. The safety chains should
be crossed and should be attached to the hitch,
not to the vehicle bumper or axle. The safety
chains can be attached to the bumper if the
hitch ball is mounted to the bumper. Be sure to
leave enough slack in the chains to permit
turning corners.
9-24Technical and consumer information
—
—
08/03/09—pattie


DOT (Department Of Transportation) Quality
Grades: All passenger car tires must conform to
federal safety requirements in addition to these
grades.
Quality grades can be found where applicable
on the tire sidewall between tread shoulder and
maximum section width. For example:
Treadwear 200 Traction AA Temperature A
TREADWEAR
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov-
ernment test course. For example, a tire graded
150 would wear one and one-half (1 1/2) times
as well on the government course as a tire
graded 100. The relative performance of tires
depends upon actual conditions of their use,
however, and may depart significantly from the
norm due to variations in driving habits, service
practices and differences in road characteristics
and climate.
TRACTION AA, A, B AND C
The traction grades, from highest to lowest, are
AA, A, B and C. Those grades represent the
tire’s ability to stop on wet pavement as mea-
sured under controlled conditions on specifiedgovernment test surfaces of asphalt and con-
crete. A tire marked C may have poor traction
performance.
WARNING
The traction grade assigned to this tire is based
on straight-ahead braking traction tests, and
does not include acceleration, cornering, hy-
droplaning, or peak traction characteristics.
TEMPERATURE A, B AND C
The temperature grades A (the highest), B, and
C, representing the tire’s resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the ma-
terial of the tire to degenerate and reduce tire
life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds to
a level of performance which all passenger car
tires must meet under the Federal Motor Vehicle
Safety Standard No. 109. Grades B and A rep-
resent higher levels of performance on the
laboratory test wheel than the minimum re-
quired by law.
WARNING
The temperature grade for this tire is estab-
lished for a tire that is properly inflated and not
overloaded. Excessive speed, under-inflation,
or excessive loading, either separately or in
combination, can cause heat build-up and pos-
sible tire failure.
UNIFORM TIRE QUALITY GRADING
9-28Technical and consumer information
—
—
08/03/09—pattie


Sun visors................... .3-21
Sunglasses holder .............. .2-47
Supplemental air bag warning labels . . . .1-53
Supplemental air bag warning light . .1-53 , 2-17
Supplemental restraint system ........1-40
Supplemental restraint system, Precautions
on supplemental restraint system ......1-40
Switch Autolight switch ............. .2-36
Continuous Damping Control mode
select switch ................ 2-44
Fog light switch .............. 2-40
Forward Collision Warning (FCW)
switch ................... 2-43
Hazard warning flasher switch ......2-40
Headlight switch .............. 2-36
Ignition switch automatic transmission
models ................... 5-13
Intelligent Brake Assist (IBA) OFF
switch ................... 2-44
Lane departure warning (LDW)
system ................... 2-42
Power door lock switch ...........3-5
Rear window and outside mirror
defroster switch .............. 2-35
Snow mode switch ............2-43
Turn signal switch ............. 2-39
Vehicle dynamic control (VDC) off
switch .................... 2-45
T
Tachometer ................... .2-7
Temperature gauge, Engine coolant
temperature gauge .............. .2-7Theft (INFINITI Vehicle Immobilizer System),
Engine start
.................. .2-31
Thigh extension ................ .1-4
Three-way catalyst ............... .5-2
Tilt/telescopic steering .............3-19
Tire pressure, Low tire pressure warning
light ...................... .2-15
Tire, Tire replacement indicator ........2-25
Tires Flat tire ................... .6-2
Low tire pressure warning system ....5-3
Spare tire ................. 8-38
Tire and Loading information label . . . 8-30
Tire chains ................. 8-35
Tire dressing ................7-4
Tire pressure ................ 8-28
Tire pressure monitoring system
(TPMS) ....................
5-3
Tire rotation ................ 8-36
Types of tires ............... 8-34
Uniform tire quality grading .......9-28
Wheel/tire size ...............9-9
Wheels and tires ............. 8-28
Tonneau cover (see cargo cover) .......2-51
Top tether strap child restraints .......1-24
Touch screen system ..............4-4
Towing Flat towing ................ .9-27
Tow truck towing .............. 6-11
Towing a trailer .............. 9-19
Towing safety ............... 9-23
TPMS, Tire pressure monitoring system . . . .5-3
TPMS, Tire pressure warning system .....6-2
Trailer towing ................. .9-19Transceiver, HomeLink
Universal
Transceiver .................. .2-60
Transmission Automatic transmission fluid (ATF) . . . .8-13
Driving with automatic transmission . . . 5-13
Transmission selector lever lock
release ................... 5-16
Transmitter
(See remote keyless entry system) ......3-13
Traveling or registering your vehicle in
another country ................ .9-10
Trip computer ................. .2-27
Trip odometer ................. .2-27
Turn signal switch .............. .2-39
U
Underbody cleaning .............. .7-3
Uniform tire quality grading .........9-28
V
Vanity mirror ................. .3-24
Vanity mirror lights ............. .2-59
Variable voltage control system . . .....8-17
Vehicle Dimensions ................ .9-10
Recovery (freeing a stuck vehicle) . . . . 6-14
Vehicle dynamic control (VDC) off
switch .................... 2-45
Vehicle dynamic control (VDC)
system ................... 5-77
Vehicle information and settings
(display) ...................

4-7
10-7
—
—
10/19/09—tbrooks


Vehicle identification number (VIN)......9-11
Vehicle loading information ..........9-15
Vehicle security system ............2-29
Ventilators .................. .4-39
Voice command (See Bluetooth Hands-Free
Phone System) ............4-105 , 4-121
Voice recognition system ..........4-129
Voice recognition, Alternate command
mode ..................... .4-142
Warning Dot matrix display .............2-21
Hazard warning flasher switch ......2-40
Lane departure warning (LDW)
system ................... 5-19
Tire pressure monitoring system
(TPMS) ....................5-3
Warning/indicator lights and audible
reminders .................. 2-12
W
Warning labels, Air bag warning labels . . .1-53
Warning light Air bag warning light ............1-53
All-wheel drive (AWD) warning light . . . 2-13
Anti-lock braking system (ABS) warning
light ..................... 2-13
Brake warning light ............2-13
Intelligent Key warning light .......2-15
Lane departure warning light .......2-15
Low tire pressure warning light .....2-15
Rear Active Steer warning light ......2-17
Seat belt warning light and chime ....2-17
Warning lights ................ .2-13Warranty, Emission control system
warranty
.................... .9-29
Washer switch, Windshield wiper and
washer switch ................ .2-32
Washing .................... .7-2
Waxing ..................... .7-2
Welcome light ................ .2-57
Wheel/tire size ................ .9-9
Wheels and tires ............... .8-28
Wheels and tires Care of wheels ............... .7-3
Cleaning aluminum alloy wheels .....7-3
Wheels, Rear Active Steer system ......5-79
Window washer fluid ............. .8-14
Window(s) Cleaning .................. .7-3
Power

windows .............. 2-53
Windshield wiper and washer switch . . . .2-32
Wiper Rain-sensing auto wiper system .....2-33
Windshield wiper and washer switch . . 2-32
Wiper blades ................ 8-19
X
Xenon headlights ............... .2-35
10-8
—
—
10/19/09—tbrooks


FUEL RECOMMENDATION:
VK50VE engine
Use unleaded premium gasoline with an octane
rating of at least 91 AKI (Anti-Knock Index)
number (Research octane number 96).
If premium gasoline is not available, unleaded
regular gasoline with an octane rating of 87 AKI
number (Research octane number 91) may be
temporarily used, but only under the following
precautions:
●Have the fuel tank filled only partially with
unleaded regular gasoline, and fill up with
unleaded premium gasoline as soon as pos-
sible.
● Avoid full throttle driving and abrupt accel-
eration.
However, for maximum vehicle performance, the
use of unleaded premium gasoline is recom-
mended.
VQ35HR engine
INFINITI recommends the use of unleaded pre-
mium gasoline with an octane rating of at least
91 AKI (Anti-Knock Index) number (Research
octane number 96).
If unleaded premium gasoline is not available,
you may use unleaded regular gasoline with an octane rating of at least 87 AKI number (Re-
search octane number 91), but you may notice a
decrease in performance.
CAUTION
●
Using a fuel other than that specified could
adversely affect the emission control sys-
tems, and may also affect warranty
coverage.
● Under no circumstances should a leaded
gasoline be used, since this will damage the
three way catalyst.
● Do not use E-85 fuel in your vehicle. Your
vehicle is not designed to run on E-85 fuel.
Using E-85 fuel can damage the fuel system
components and is not covered by the
INFINITI vehicle limited warranty.
ENGINE OIL RECOMMENDATION:
● Engine oil with API Certification Mark
● Viscosity SAE 5W-30
See “CAPACITIES AND RECOMMENDED
FUEL/LUBRICANTS” in the “9. Technical and
consumer information” section for engine oil
and oil filter recommendation.
COLD TIRE PRESSURES:
The label is typically located on the driver side
center pillar or on the driver’s door. For addi-
tional information, see “WHEELS AND TIRES” in
the “8. Maintenance and do-it-yourself” sec-
tion.
NEW VEHICLE BREAK-IN PROCEDURES
RECOMMENDATION:
During the first 1,200 miles (2,000 km) of
vehicle use, follow the recommendations out-
lined in the “BREAK-IN SCHEDULE” in the “5.
Starting and driving” section of this Owner’s
Manual. Follow these recommendations for the
future reliability and economy of your new
vehicle.
GAS STATION INFORMATION
—
—
10/19/09—tbrooks