battery INFINITI FX 2010 Workshop Manual

Check the fluid level in each cell (Remove the
battery cover if it is necessary). It should be
between the UPPER LEVEL
1and LOWER LEVEL
2lines.
If it is necessary to add fluid, add only distilled
water to bring the level to the indicator in each
filler opening. Do not overfill.
1. Remove the cell plugsA.
2. Add distilled water up to the UPPER LEVEL
1line.
If the side of the battery is not clear, check
the distilled water level by looking directly
above the cell; the condition
1indicates
OK and the conditions
2needs more to be
added.
3. Tighten cell plugsA.
Vehicles operated in high temperatures or un-
der severe conditions require frequent checks
of the battery fluid level.
JUMP STARTING
If jump starting is necessary, see “JUMP START-
ING” in the “6. In case of emergency” section. If
the engine does not start by jump starting, the
battery may have to be replaced. Contact an
INFINITI retailer.
DI0137MASDI1480C
8-16Maintenance and do-it-yourself
—
—
08/03/09—pattie


CAUTION
●Do not ground accessories directly to the
battery terminal. Doing so will bypass the
variable voltage control system and the ve-
hicle battery may not charge completely.
● Use electrical accessories with the engine
running to avoid discharging the vehicle
battery.
The variable voltage control system measures
the amount of electrical discharge from the
battery and controls voltage generated by the
generator.
1. Water pump
2. Alternator
3. Crankshaft pulley
4. Power steering fluid pump
5. Air conditioner compressor 1. Power steering fluid pump
2. Alternator
3. Crankshaft pulley
4. Air conditioner compressor
5. Drive belt auto-tensioner
WARNING
Be sure the ignition switch is in the OFF or LOCK
position before servicing drive belts. The en-
gine could rotate unexpectedly.
VK50VE engine
SDI1411B
VQ35HR engine
SDI2152
VARIABLE VOLTAGE CONTROL SYSTEM DRIVE BELTS
Maintenance and do-it-yourself8-17
—
—
08/03/09—pattie


ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage
rating than that specified on the fuse box cover.
This could damage the electrical system or
cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to the OFF or LOCK position and the head-
light switch is turned to OFF.
2. Open the engine hood and remove the cover on the battery. 3. Remove the fuse/fusible link holder
cover.
4. Remove the fuse with the fuse puller.
5. If the fuse is open
A, replace it with a
new fuse
B. Spare fuses are stored in the
passenger compartment fuse box.
6. If a new fuse also opens, have the elec- trical system checked and repaired by an
INFINITI retailer.
Fusible links
If any electrical equipment does not operate
and fuses are in good condition, check the
fusible links. If any of these fusible links are
melted, replace only with genuine INFINITI
parts.
SDI1479ASDI1754
FUSES
8-22Maintenance and do-it-yourself
—
—
08/03/09—pattie


PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage
rating than that specified on the fuse box cover.
This could damage the electrical system or
cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Be sure the ignition switch is pushed to the OFF or LOCK position and the head-
light switch is turned to OFF.
2. Open the fuse box lid.
3. Remove the fuse with the fuse puller
A. 4. If the fuse is open, replace it with a new
fuse.
5. If a new fuse also opens, have the electri- cal system checked and repaired by an
INFINITI retailer. Spare fuses are stored in
the fuse box.
Replace the battery as follows:
1. Release the lock knob at the back of theIntelligent Key and remove the mechanical
key.
2. Insert a flat-blade screwdriver
A
wrapped with a cloth into the slitBof
the corner and twist it to separate the
upper part from the lower part.
SDI2034SPA1875
INTELLIGENT KEY BATTERY REPLACEMENT
Maintenance and do-it-yourself8-23
—
—
08/03/09—pattie


3. Replace the battery with a new one.
Recommended battery: CR2032 or equiva-
lent.
● Do not touch the internal circuit and
electric terminals as it could cause a
malfunction.
● Hold the battery by the edges. Holding
the battery across the contact points will
seriously deplete the storage capacity.
● Make sure that the + side faces the
bottom of the case.
4. Align the tips of the upper and lower parts, and then push them together until
it is securely closed.
5. Push the buttons two or three times to check its operation.
See an INFINITI retailer if you need any assis-
tance for replacement. FCC Notice:
This equipment has been tested and found to
comply with the limits for a Class B digital device
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential in-
stallation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
–
Reorient or relocate the receiving antenna
– Increase the separation between the equip-
ment and the receiver
– Connect the equipment into an outlet on a
circuit different from that to which the re-
ceiver is connected.
– Consult the retailer or an experienced
radio/TV technician for help.
SDI2285
8-24Maintenance and do-it-yourself
—
—
08/03/09—tbrooks


Trailer lights
CAUTION
When splicing into the vehicle electrical sys-
tem, a commercially available power-type
module/converter must be used to provide
power for all trailer lighting. This unit uses the
vehicle battery as a direct power source for all
trailer lights while using the vehicle tail light,
stoplight and turn signal circuits as a signal
source. The module/converter must draw no
more than 15 milliamps from the stop and tail
lamp circuits. Using a module/converter that
exceeds these power requirements may dam-
age the vehicle’s electrical system. See a repu-
table trailer retailer to obtain the proper equip-
ment and to have it installed.
Trailer lights should comply with federal and/or
local regulations. For assistance in hooking up
trailer lights, contact an INFINITI retailer or
reputable trailer retailer.
Trailer brakes
If your trailer is equipped with a braking sys-
tem, make sure it conforms to federal and/or
local regulations and that it is properly in-
stalled.
WARNING
Never connect a trailer brake system directly to
the vehicle brake system.
Pre-towing tips
● Be certain your vehicle maintains a level
position when a loaded or unloaded trailer is
hitched. Do not drive the vehicle if it has an
abnormal nose-up or nose-down condition;
check for improper tongue load, overload,
worn suspension or other possible causes of
either condition.
● Always secure items in the trailer to prevent
load shift while driving.
● Keep the cargo load as low as possible in the
trailer to keep the trailer center of gravity
low.
● Load the trailer so approximately 60% of the
trailer load is in the front half and 40% is in
the back half. Also make sure the load is
balanced side to side.
● Check your hitch, trailer tire pressure, ve-
hicle tire pressure, trailer light operation,
and trailer wheel lug nuts every time you
attach a trailer to the vehicle.
● Be certain your rearview mirrors conform to
all federal, state or local regulations. If not, install any mirrors required for towing before
driving the vehicle.
● Determine the overall height of the vehicle
and trailer so the required clearance is
known.Trailer towing tips
In order to gain skill and an understanding of
the vehicle’s behavior, you should practice turn-
ing, stopping and backing up in an area which
is free from traffic. Steering stability, and brak-
ing performance will be somewhat different
than under normal driving conditions.
● Always secure items in the trailer to prevent
load shift while driving.
● Lock the trailer hitch coupler with a pin or
lock to prevent the coupler from inadvert-
ently becoming unlatched.
● Avoid abrupt starts, acceleration or stops.
● Avoid sharp turns or lane changes.
● Always drive your vehicle at a moderate
speed. Some states or provinces have spe-
cific speed limits for vehicles that are towing
trailers. Obey the local speed limits.
● When backing up, hold the bottom of the
steering wheel with one hand. Move your
hand in the direction in which you want the
trailer to go. Make small corrections and
Technical and consumer information9-25
—
—
08/03/09—pattie


You may notify INFINITI by contacting our
Consumer Affairs Department, toll-free,
at 1-800-662-6200.A vehicle equipped with All-Wheel Drive (AWD)
should never be tested using a two wheel
dynamometer (such as the dynamometers used
by some states for emissions testing), or similar
equipment. Make sure you inform test facility
personnel that your vehicle is equipped with
AWD before it is placed on a dynamometer.
Using the wrong test equipment may result in
transmission damage or unexpected vehicle
movement which could result in serious vehicle
damage or personal injury.
Due to legal requirements in some states/ areas
or provinces, your vehicle may be required to be
in what is called the “ready condition” for an
Inspection/Maintenance (I/M) test of the emis-
sion control system.
The vehicle is set to the “ready condition” when
it is driven through certain driving patterns.
Usually, the “ready condition” can be obtained
by ordinary usage of the vehicle.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready condition”. Before taking
the I/M test, check the vehicle’s
inspection/maintenance test readiness condi-
tion. Push the ignition switch to the ON position
without starting the engine. If the Malfunction
Indicator Light (MIL) comes on steady for 20
seconds and then blinks for 10 seconds, the I/Mtest condition is “not ready”. If the MIL does not
blink after 20 seconds, the I/M test condition is
“ready”.
If the MIL indicates the vehicle is in a “not
ready” condition, drive the vehicle through the
following pattern to set the vehicle to the
“ready condition”. If you cannot or do not want
to perform the driving pattern, an INFINITI re-
tailer can conduct it for you.
WARNING
Always drive the vehicle in a safe and prudent
manner according to traffic conditions and
obey all traffic laws.
1. Start the engine. Allow the engine to idle
until the engine coolant temperature
gauge needle points between the C and H
(normal operating temperature).
2. Accelerate the vehicle to 55 MPH (88 km/h), then quickly release the accelera-
tor pedal completely and keep it released
for at least 10 seconds.
3. Quickly depress the accelerator pedal for a moment, then drive the vehicle at a
speed of 53 to 60 MPH (86 to 96 km/h) for
at least 9 minutes.
4. Stop the vehicle. Leave the engine run- ning.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST
9-30Technical and consumer information
—
—
08/03/09—pattie


10 Index
A
ABS (Anti-lock Braking System) ........5-76
Adaptive front lighting system (AFS) .....2-38
Advanced air bag system ...........1-45
Aiming control, Adaptive front lighting
system (AFS) ................. .2-38
Air bag system Advanced air bag system .........1-45
Front passenger air bag and status
light ..................... 1-47
Front-seat mounted side-impact
supplemental air bag system .......1-50
Roof-mounted curtain side-impact and
rollover supplemental air bag system . . 1-50
Air bag warning labels .............1-53
Air bag warning light ..........1-53 , 2-17
Air cleaner housing filter ...........8-19
Air conditioner Advanced Climate Control System
(ACCS) ................... .4-44
Air conditioner service ..........4-46
Air conditioner specification label ....9-13
Air conditioning system refrigerant and
lubricant recommendations .......4-46
Automatic climate control ........4-40
In-cabin microfilter ............4-45
Operation (See automatic climate
control) ................... 4-40
Alarm, How to stop alarm
(see vehicle security system) .........2-31Alcohol, drugs and driving
...........5-7
All-wheel drive (AWD) .............5-69
All-wheel drive (AWD) warning light .....2-13
Antenna .................... .4-90
Anti-lock Braking System (ABS) ........5-76
Anti-lock braking system (ABS) warning
light ...................... .2-13
Appearance care Exterior appearance care ..........7-2
Interior appearance care ..........7-4
Armrest .................... .1-12
Around view monitor .............4-28
Audible reminders .............. .2-20
Audio operation precautions .........4-46
Audio system ................. .4-46
Audio system, Steering wheel audio
controls .................... .4-89
Auto closure .................. .3-17
Autolight

system ............... .2-36
Automatic Automatic transmission fluid (ATF) . . . .8-13
Climate control .............. 4-40
Driving with automatic transmission . . . 5-13
Automatic door locks ..............3-5
Automatic drive positioner ..........3-25
Automatic seat positioner ...........3-25
Average fuel consumption and speed . . . .2-27
Avoiding collision and rollover .........5-5 B
Back door (See lift gate) ............3-16
Battery ..................... .8-15
Battery Battery saver system ............2-37
Intelligent Key ............... 8-23
Variable voltage control system . ....8-17
Before starting the engine ...........5-12
Belts (See drive belts) .............8-17
Bluetooth hands-free phone system
(models with navigation system) ......4-104
Booster seats ................. .1-35
Brake Anti-lock Braking System (ABS) ......5-76
Brake fluid ................. 8-14
Brake system ................ 5-73
Parking brake operation ..........5-17
Brake warning light ............. .2-13
Break-in schedule .............. .5-68
Brightness control and display ON/OFF
button ...................... .4-7
Brightness control, Instrument panel . . . .2-39
Bulb check/instrument panel . . . . . . . . .2-12
Bulb replacement .............. .8-25
—
—
10/19/09—tbrooks


I
Ignition switch (Push-button) ..........5-9
Ignition switch, Automatic transmission
models ..................... .5-13
Immobilizer system .............. .2-31
In-cabin microfilter .............. .4-45
Indicator lights ................ .2-18
Indicator, Dot matrix display .........2-21
INFINITI Vehicle Immobilizer System .....2-31
INFINITI voice recognition standard
mode ..................... .4-130
INFINITI voice recognition system ......4-129
INFO button .................. .4-8
Inside mirror ................. .3-21
Inspection/maintenance (I/M) test ......9-30
Instrument brightness control ........2-39
Instrument panel ............... .2-4
Intelligent Brake Assist (IBA) off indicator
light ...................... .2-18
Intelligent Brake Assist (IBA) system .....5-64
Intelligent Cruise Control (ICC) system
(Full Speed Range) .............. .5-28
Intelligent Cruise Control (ICC) system
MAIN switch indicator .............2-24
Intelligent Cruise Control (ICC) system
warning light ................. .2-15
Intelligent cruise control (ICC) system,
Preview function ............... .5-49
Intelligent Key ................. .3-2
Intelligent Key battery discharge
indicator ................... .2-24
Intelligent Key insertion indicator ......2-23
Intelligent Key removal indicator .......2-23Intelligent Key system
.............3-6
Intelligent Key system Battery replacement ............8-23
Key operating range ............3-8
Key operation ................3-9
Warning light ................ 2-15
Warning signals .............. 3-11
Intelligent Key warning light ..........2-15
Interior light control switch ..........2-58
Interior light replacement ...........8-26
Interior lights ................. .2-58
iPod player

operation ............4-78
ISOFIX child restraint ............. .1-22
J
Jump starting .................. .6-7
K
Keyless entry
(See remote keyless entry system) ......3-13
Keys ....................... .3-2
Keys, For Intelligent Key system ........3-6
Labels Air bag warning labels ...........1-53
Air conditioner specification label ....9-13
Emission control information label . . . 9-12
Engine serial number ...........9-12
F.M.V.S.S./C.M.V.S.S. certification
label ..................... 9-12
Tire and Loading information label . . . 9-13
Vehicle identification number (VIN) . . . 9-11 L
Lane Departure Prevention (LDP) ON
indicator light ................. .2-19
Lane Departure Prevention (LDP) system . . .5-21
Lane departure warning (LDW) switch . . . .2-42
Lane departure warning (LDW) system . . . .5-19
Lane Departure Warning (LDW) system/Lane
Departure Prevention (LDP) system ......5-18
Lane departure warning chime . .......2-21
Lane departure warning light .........2-15
LATCH system ................. .1-22
License plate, Installing front license
plate ...................... .9-14
Lift gate .................... .3-16
Light Air bag warning light ............1-53
Bulb replacement ............. 8-25
Cargo light ................. 2-60
Fog light switch .............. 2-40
Headlight switch .............. 2-36
Headlights bulb replacement . . . . . . 8-26
Indicator lights ............... 2-18
Interior light control switch .......2-58
Interior lights ............... 2-58
Map lights ................. 2-58
Personal lights ............... 2-58
Vanity mirror lights ............2-59
Warning/indicator lights and audible
reminders .................. 2-13
Xenon

headlights ............. 2-35
Light replacement .............. .8-25
Lights, Exterior and interior light
replacement ................. .8-26
10-4
—
—
10/19/09—tbrooks


Loading information
(See vehicle loading information).......9-15
Lock Automatic door locks ............3-5
Door locks ..................3-4
Lift gate lock ................ 3-16
Power door lock ...............3-4
Locking with mechanical key ..........3-4
Low fuel warning ............... .2-24
Low outside temperature warning ......2-24
Low tire pressure warning light ........2-15
Low tire pressure warning system (See tire
pressure monitoring system (TPMS)) .....5-3
Low washer fluid warning ...........2-24
Luggage hooks ................ .2-50
Maintenance Battery ................... .8-15
General maintenance ............8-2
Indicators for maintenance
(dot matrix) ................. 2-25
Inside the vehicle ..............8-3
Maintenance precautions .........8-5
Maintenance requirements ........8-2
Outside the vehicle .............8-2
Seat belt maintenance ..........1-20
M
Malfunction indicator light (MIL) .......2-19
Map lights .................. .2-58
Master warning light ............. .2-17
Mechanical key (Intelligent Key system) . . .3-3
Memory storage, Automatic drive
positioner ................... .3-26Meter
Trip computer ............... .2-27
Meters and gauges .............. .2-5
Meters and gauges, Instrument brightness
control ..................... .2-39
Mirror Inside mirror ............... .3-21
Outside mirrors .............. 3-23
Monitor, Rearview monitor ..........4-22
Moonroof ................... .2-56
N
Net, Cargo net ................ .2-50
New vehicle break-in .............5-68
No key warning ................ .2-23
O
Odometer .................... .2-6
Off-road

recovery ............... .5-6
Oil Capacities and recommended fuel/
lubricants .................. .9-2
Changing engine oil and filter ......8-11
Checking engine oil level .........8-10
Engine oil .................. 8-10
Engine oil viscosity .............9-6
Oil filter replacement indicator ......2-25
Operation, Indicators for operation
(dot matrix) .................. .2-23
Outside air temperature ............2-28
Outside mirrors ................ .3-23Owner’s Manual/Service Manual order
information
.................. .9-32
P
Panic alarm .................. .3-14
Parking Parking brake operation . . . . . . . . . .5-17
Parking brake release warning ......2-24
Parking on hills .............. 5-71
Parking brake break-in .............5-73
Personal lights ................ .2-58
Phone, Car phone or CB radio ........4-103
Power Power door lock .............. .3-4
Power outlet ................ 2-45
Power steering fluid ............8-13
Power steering system ..........5-72
Power windows .............. 2-53
Power front seat adjustment ..........1-2
Pre-crash seat belts with comfort function . .1-16
Precautions Audio operation ............. .4-46
Braking precautions ............5-73
Child restraints .............. 1-20
Cruise control ............... 5-26
Driving safety ................5-7
Maintenance .................8-5
On-pavement and off-road driving ....5-5
Seat belt usage ............... 1-12
Supplemental restraint system ......1-40
When

starting and driving . . .......5-2
Preview function ............... .5-74
Preview function (for Intelligent cruise control
system) .................... .5-49
10-5
—
—
10/19/09—tbrooks