pg power INFINITI FX35 2004 Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: FX35, Model: INFINITI FX35 2004Pages: 4449, PDF Size: 99.66 MB
Page 4130 of 4449
SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION SE
A
B
SE
Revision: 2004 November 2004 FX35/FX45
SEAT
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Service Notice .......................................................... 3
Precautions for Work ................................................ 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSIS ...... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
AUTOMATIC DRIVE POSITIONER ...........................11
System Description ................................................. 11
MANUAL OPERATION ........................................ 11
AUTOMATIC OPERATION .................................. 11
MEMORY STORING AND KEY FOB INTER-
LOCK STORING .................................................. 11
MEMORY SWITCH OPERATION ....................... 13
ENTRY OPERATION .......................................... 13
EXITING OPERATION ........................................ 13
KEY FOB INTERLOCK OPERATION ................. 14
FAIL- SAFE MODE ............................................. 14
CANCEL OF FAIL-SAFE MODE ......................... 14
Component Parts and Harness Connector Location ... 15CAN Communication System Description .............. 16
CAN Communication Unit ....................................... 16
Schematic ............................................................... 17
Wiring Diagram–AUT/DP– ...................................... 19
Terminals and Reference Values for BCM .............. 30
Terminals and Reference Values for Automatic
Drive Positioner Control Unit .................................. 30
Terminals and Reference Values for Driver Seat
Control Unit ............................................................. 32
Work Flow ............................................................... 34
Preliminary Check .................................................. 35
SETTING CHANGE FUNCTION ......................... 35
CHECK POWER SUPPLY AND GROUND ......... 35
CONSULT-II Function ............................................. 38
CONSULT-II INSPECTION PROCEDURE .......... 38
SELF-DIAGNOSIS RESULTS ............................. 39
CAN DIAGNOSIS SUPPORT MONITOR ............ 40
DATA MONITOR ................................................. 40
ACTIVE TEST ..................................................... 41
Can Communication Inspection Using CONSULT-
II (Self-diagnosis) .................................................... 42
Symptom Chart ....................................................... 42
Sliding Motor Circuit Check .................................... 44
Reclining Motor Circuit Check ................................ 45
Front Lifting Motor Circuit Check ............................ 46
Rear Lifting Motor Circuit Check ............................. 48
Telescopic Motor Circuit Check .............................. 49
Tilt Motor Circuit Check .......................................... 51
Driver Side Mirror Motor Circuit Check ................... 52
Passenger Side Mirror Motor Circuit Check ........... 54
Sliding Sensor Circuit Check .................................. 56
Reclining Sensor Circuit Check .............................. 57
Front Lifting Sensor Circuit Check .......................... 58
Rear Lifting Sensor Circuit Check .......................... 59
Telescopic Sensor Circuit Check ............................ 60
Tilt Sensor Circuit Check ........................................ 61
Driver Side Mirror Sensor Circuit Check ................. 62
Passenger Side Mirror Sensor Circuit Check ......... 63
Steering and Door Mirror Sensor Power and Ground
Circuit Check .......................................................... 64
Page 4131 of 4449
SE-2Revision: 2004 November 2004 FX35/FX45Front Door Switch (Driver Side) Circuit Check ....... 65
Sliding Switch Circuit Check ................................... 67
Reclining Switch Check .......................................... 68
Front Lifting Switch Circuit Check ........................... 70
Rear Lifting Switch Circuit Check ........................... 71
Sliding Switch and Reclining Switch Ground Circuit
Check ..................................................................... 72
Front Lifting Switch and Rear Lifting Switch Ground
Circuit Check .......................................................... 73
Telescopic Switch Circuit Check ............................. 74
Tilt Switch Circuit Check ......................................... 76
Door Mirror Remote Control Switch (Changeover
switch) Circuit Check .............................................. 78
Door Mirror Remote Control Switch (Mirror Switch)
Circuit Check .......................................................... 80
Detention Switch (P Range Switch) Circuit Check ... 82
Key Switch and Key Lock Solenoid Circuit Check
(With Intelligent Key) .............................................. 83
Key Switch Circuit Check (Without Intelligent Key) ... 85
Seat Memory Switch Circuit Check ........................ 86
Memory Indicator Lamp Circuit Check .................... 88
Uart Communication Line Circuit Check ................. 89
Lumber Support Circuit Check ............................... 91
POWER SEAT ........................................................... 93
Automatic Drive Positioner Interlocking Power Seat ... 93
Schematic ............................................................... 94Wiring Diagram–SEAT– / For Driver Seat ............... 95
Wiring Diagram–SEAT– / For Passenger Seat ....... 97
HEATED SEAT .......................................................... 98
Description .............................................................. 98
Wiring Diagram – HSEAT – .................................... 99
FRONT SEAT ..........................................................101
Removal and Installation .......................................101
REMOVAL ..........................................................103
INSTALLATION ..................................................104
REMOVAL OF SEATBACK TRIM AND PAD .....104
INSTALLATION OF SEATBACK TRIM AND PAD .105
REMOVAL OF SEAT CUSHION TRIM AND PAD .105
INSTALLATION OF SEAT CUSHION TRIM AND
PAD ....................................................................106
REAR SEAT .............................................................107
Removal and Installation .......................................107
REMOVAL ..........................................................109
INSTALLATION ..................................................109
REMOVAL OF SEAT CUSHION TRIM AND PAD .109
INSTALLATION OF SEAT CUSHION TRIM AND
PAD ....................................................................110
REMOVAL OF SEATBACK TRIM AND PAD .....110
INSTALLATION OF SEATBACK TRIM AND PAD .110
REMOVAL OF REMOTE CONTROL LEVER .... 111
INSTALLATION OF REMOTE CONTROL
LEVER ............................................................... 111
Page 4140 of 4449
AUTOMATIC DRIVE POSITIONER
SE-11
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
AUTOMATIC DRIVE POSITIONERPFP:28491
System Description AIS002XB
The system automatically moves the driver seat to facilitate entry/exit to/from the vehicle. The automatic
driver positioner control unit can also store the optimum driving positions (driver seat, pedal position and
door mirror position) for 2 people. If the driver is changes, one-touch operation allows changing to the
other driving position.
The settings (ON/OFF) of the automatic sliding seat (Entry/Exiting operation) at entry/exit can be changed
as desired, using the display unit in the center of the instrument panel. The set content is transmitted by
CAN communication, from display unit (without NAVI) or display control unit (with NAVI) to driver seat con-
trol unit.
Using CONSULT-II, the seat slide amount at entry/exit setting can be changed.
MANUAL OPERATION
The driving position [seat position, steering wheel position (tilt, telescopic) and door mirror position] can be
adjusted with the power seat switch or ADP steering switch or door mirror remote control switch.
NOTE:
The seat can be manually operated with the ignition switch OFF.
The door mirrors can be manually operated with the ignition switch turned ACC or ON.
A U T O M AT I C O P E R AT I O N
NOTE:
Disconnecting the battery erases the stored memory.
After connecting the battery, insert the key into the ignition cylinder and turn the driver door switch ON (open)→OFF (close)→ON
(open), the Entry/ Exiting operation becomes possible.
After exiting operation is carried out, return operation can be operated.
NOTE:
During automatic operation, if the ignition switch is turned ON→START, the automatic operation is suspended. When the ignition switch
returns to ON, it resumes.
MEMORY STORING AND KEY FOB INTERLOCK STORING
Store the 2 driving positions and shifts to the stored driving position with the memory switch.
Function Description
Memory switch operation The seat, steering and door mirror move to the stored driving position by pushing
memory switch (1 or 2).
Entry/Exiting functionExiting operation At exit, the seat moves backward and steering wheel moves forward/upward.
Entry operationAt entry, the seat and steering wheel returns from the exiting position to the previous
driving position.
Key fob interlock operationPerform memory operation, exiting operation and entry operation by pressing key fob
unlock button.
Auto operation temporary stop
conditions.When ignition switch turned to START during memory switch operation and return opera-
tion, memory switch operation and entry operation is stopped.
Auto operation stop conditions.
When the vehicle speed becomes 7 km/h (4 MPH) or higher.
When the setting switch, memory switch 1, or 2 are pressed.
When A/T selector lever is in any position other than P.
When the door mirror remote control switch is operated (when ignition switch turned to
ON or ACC).
When power seat switch turned ON.
When ADP steering switch turned ON (telescopic operation or tilt operation).
When door mirror operates (only memory switch operation).
When driver seat sliding Entry/Exiting setting is OFF (only entry/exiting operation).
When steering wheel tilt and telescopic Entry/Exiting setting is OFF (only entry/exiting
operation).
When the tilt and telescopic sensor malfunction is detected.
Page 4159 of 4449
SE-30
AUTOMATIC DRIVE POSITIONER
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Values for BCMAIS002XG
Terminals and Reference Values for Automatic Drive Positioner Control UnitAIS002XH
TERMINAL WIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
11 LG/R ACC power supply Ignition switch ACC Battery voltage
37 B/W Key switch signalKey switch ON (key is inserted in
ignition key cylinder)Battery voltage
Key switch OFF (key is removed
from ignition key cylinder)0
38 W/L Ignition power supply Ignition switch ON Battery voltage
39 L CAN-H — —
40 R CAN-L — —
42 L/R Battery power supply (fuse) Ignition switch OFF Battery voltage
49 B Ground (signal) Ignition switch ON 0
52 B Ground (power) Ignition switch ON 0
55 GBattery power supply (Fusible
link)Ignition switch OFF Battery voltage
62 W Front door switch (driver side) ON (Open) → OFF (Closed) 0 → Battery voltage
TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
1 LG/R Tilt switch UP signalTilt switch turned to upward 0
Tilt switch neutral position 5
2 G/W Changeover switch RH signalWhen changeover switch in RH posi-
tion0
When changeover switch in neutral
position5
3 GY Mirror switch UP signalWhen mirror switch in turned to
upward position0
When mirror switch in neutral position 5
4 Y Mirror switch LEFT signalWhen mirror switch in turned to left-
ward position0
When mirror switch in neutral position 5
5ORPassenger side mirror sensor
(vertical) signalWhen passenger side mirror motor is
UP or DOWN operationChanges between 3 (close to perk)
1 (close to valley)
6P/LDriver side mirror sensor (verti-
cal) signalWhen driver side mirror motor is UP
or DOWN operationChanges between 3 (close to perk)
1 (close to valley)
7 Y/R Tilt sensor inputTilt position, top 1.82
Tilt position, bottom 4.44
10 B UART LINE (TX) Memory switch 1 or 2 operated
11 BR Telescopic switch forward signalTelescoping switch turned to forward 0
Telescoping switch neutral position 5
PIIA4813E
Page 4160 of 4449
AUTOMATIC DRIVE POSITIONER
SE-31
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
14 L/WPassenger side mirror motor UP
signalWhen passenger side mirror motor
UP operation1.5 - Battery voltage
Passenger side mirror motor OFF 0
15 L/BPassenger side mirror motor sig-
nalWhen passenger side mirror motor
LEFT operation1.5 - Battery voltage
Passenger side mirror motor RH OFF 0
16 PDriver side mirror motor DOWN
signalWhen driver side mirror motor DOWN
operation1.5 - Battery voltage
Driver side mirror motor OFF 0
Driver side mirror motor RIGTH
signalWhen driver side mirror motor RIGHT
operation1.5 - Battery voltage
Driver side mirror motor OFF 0
17 R/B Tilt switch DOWN signalTilt switch turned to downward 0
Tilt switch neutral position 5
18 L/OR Changeover switch LH signalWhen changeover switch in LH posi-
tion0
When changeover switch in neutral
position5
19 GY/L Mirror switch DOWN signalWhen mirror switch in turned to down-
ward position0
When mirror switch in neutral position 5
20 PU Mirror switch RIGHT signalWhen mirror switch in turned to right-
ward position0
When mirror switch in neutral position 5
21 G/YPassenger side mirror sensor
(horizontal) signalWhen passenger side mirror motor is
LEFT or RIGHT operationChanges between 1 (close to left
edge) 3 (close to right edge)
22 L/YDriver side mirror sensor (hori-
zontal) signalWhen driver side mirror motor is LEFT
or RIGHT operationChanges between 1 (close to right
edge) 3 (close to left edge)
23 Y/B Telescopic sensor inputTelescoping position, top 0.56
Telescoping position, bottom 4.44
26 W UART LINE (RX) Memory switch 1 or 2 operated
27 LGTelescopic switch backward sig-
nalTelescopic switch turned to backward 0
Telescoping switch neutral position 5
28 SB Ignition START power supply Ignition switch START Battery voltage
30 W/RPassenger side mirror motor
DOWN signalWhen passenger side mirror motor
downward1.5 - Battery voltage
Passenger side mirror motor OFF 0
Passenger side mirror motor
RIGTH signalWhen passenger side mirror motor
RIGHT operation1.5 - Battery voltage
Passenger side mirror motor OFF 0
31 R/WDriver side mirror motor UP sig-
nalWhen driver side mirror motor upward 1.5 - Battery voltage
Driver side mirror motor OFF 0 TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
PIIA4814E
Page 4161 of 4449
SE-32
AUTOMATIC DRIVE POSITIONER
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Values for Driver Seat Control UnitAIS002XI
32 G/BDriver side mirror motor LEFT
signalWhen driver side mirror motor LEFT
operation1.5 - Battery voltage
Driver side mirror motor OFF 0
33 G/W Sensor power supply — 5
34 L/R Battery power supply Ignition switch OFF Battery voltage
35 R/L Tilt motor UP signalTilt switch turned to upward Battery voltage
Tilt switch OFF 0
36 L/R Telescopic motor forward signalTelescoping switch turned to forward Battery voltage
OFF 0
39 W/R Battery power supply Ignition switch OFF Battery voltage
40 B Ground (signal) Ignition switch ON 0
41 B/Y Sensor ground — 0
42 R/B Tilt motor DOWN signalTilt switch turned to downward Battery voltage
Tilt switch OFF 0
44 L/WTelescopic motor backward sig-
nalTelescoping switch turned to back-
wardBattery voltage
Telescoping switch OFF 0
48 B Ground (power) Ignition switch ON 0 TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
TERMI-
NAL WIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
1A R Battery power supply Ignition switch OFF Battery voltage
2 P UART LINE (TX) —
3 G Sliding motor forward signalSliding switch turned to forward (Motor
operated)Battery voltage
OFF 0
4 G/L Reclining motor FR signalReclining switch turned to forward
(Motor operated)Battery voltage
OFF 0
5LGFront lifting motor DOWN
signalFront lifting switch turned to downward
(Motor operated)Battery voltage
OFF 0
6 G/W Rear lifting motor UP signalRear lifting switch turned to upward
(Motor operated)Battery voltage
OFF 0
7 G/BRear lifting motor DOWN
signalRear lifting switch turned to downward
(Motor operated)Battery voltage
OFF 0
PIIA4814E
Page 4162 of 4449
AUTOMATIC DRIVE POSITIONER
SE-33
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
8 G/Y UART LINE (RX) —
9 BR IGN START power supply Ignition switch START Battery voltage
10 G/R Sliding motor RR signalSliding switch turned to backward
(Motor operated)Battery voltage
OFF 0
11A R/W Battery power supply Ignition switch OFF Battery voltage
12 G/Y Reclining motor RR signalReclining switch turned to backward
(Motor operated)Battery voltage
OFF 0
13 YFront lifting motor UP out-
put signalFront lifting switch turned to upward
(Motor operated)Battery voltage
OFF 0
14 OR CAN-H — —
15 SB CAN-L — —
16A B Ground (power) Ignition switch ON 0
17 PU Detention switch signalSelector lever other than P position Battery voltage
Selector lever is sifted to P position 0
18 G Seat sliding sensor signalON (sliding motor operation)
Other than above 0 or 5
19 G/Y Front lifting sensor signalON (front lifting motor operation)
Other than above 0 or 5
22 L/GPower seat memory switch
1 signalMemory switch 1 ON 0
Memory switch 1 OFF 5
23 Y/WPower seat memory switch
indictor 1 signalMemory switch 1 ON 1
Memory switch 1 OFF Battery voltage
24 L/RSeat sliding switch forward
signalON (seat sliding switch turned to for-
ward)0
OFF Battery voltage
25 L/ORSeat reclining switch for-
ward signalON (seat reclining switch turned to for-
ward)0
OFF Battery voltage TERMI-
NAL WIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
PIIA4813E
PIIA3277E
SIIA0691J
Page 4163 of 4449
SE-34
AUTOMATIC DRIVE POSITIONER
Revision: 2004 November 2004 FX35/FX45
Work Flow AIS002XJ
1. Check the symptom and customer's requests.
2. Understand the system description. Refer to SE-11, "
System Description" .
3. Perform the preliminary check, refer to SE-35, "
Preliminary Check" .
4. Perform the CAN communication inspection using CONSULT-II, refer to SE-38, "
CONSULT-II Function"
5. Perform the self-diagnosis. Refer to SE-42, "Can Communication Inspection Using CONSULT-II (Self-
diagnosis)" .
6. Repair or replace depending on the self-diagnostic results.
26 L/P Front lifting switch UP signalON (front lifting switch turned to upward) 0
OFF Battery voltage
27 L Rear lifting switch UP signalON (rear lifting switch turned to upward) 0
OFF Battery voltage
28C B/W Sensor ground Ignition switch ON 0
29 G/L Reclining sensorON (reclining motor operation)
Other than above 0 or 5
30 G/W Rear lifting sensorON (rear lifting motor operation)
Other than above 0 or 5
34 L/W Set switch signalSet witch ON 0
Set witch OFF 5
35 L/BPower seat memory switch
2 signalMemory switch 2 ON 0
Memory switch 2 OFF 5
36 Y/GPower seat memory switch
indictor 2 signalMemory switch 2 ON 1
Memory switch 2 OFF Battery voltage
37 L/PSeat sliding switch back-
ward signalON (seat sliding switch turned to back-
ward)0
OFF Battery voltage
38 LG/BSeat reclining switch back-
ward signalON (seat reclining switch turned to
backward)0
OFF Battery voltage
39 L/GFront lifting switch DOWN
signalON (front lifting switch turned to down-
ward)0
OFF Battery voltage
40 L/YRear lifting switch DOWN
signalRear lifting switch turned to downward) 0
OFF Battery voltage
61E B/Y Ground (signal) Ignition switch ON 0 TERMI-
NAL WIRE
COLORITEM CONDITIONVOLTAGE (V)
(Approx.)
SIIA0692J
SIIA0693J
Page 4164 of 4449
AUTOMATIC DRIVE POSITIONER
SE-35
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
7. Based on the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to SE-42,
"Symptom Chart" .
8. Does the automatic drive positioner system operate normally?
If it is normal, GO TO 8.
If it is not normal, GO TO 3.
9. INSPECTION END
Preliminary CheckAIS002XK
SETTING CHANGE FUNCTION
The settings of the automatic driving positioner system can be changed, using CONSULT-II and the display
unit in the center of the instrument panel.
×: Applicable –: Not applicable
It is possible to set sliding driver seat for entry/exit of vehicle by pressing set switch.
NOTE:
After the setting is registered, the new setting is effective, even if the battery is disconnected.
CHECK POWER SUPPLY AND GROUND
1. CHECK FUSE
Check if any of the following fuses in the BCM are blown.
NOTE:
Refer to SE-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blownout, be sure to eliminate cause of malfunction before installing new fuse. Refer to
SE-15, "
Component Parts and Harness Connector Location" .
Setting item ContentCONSULT–II
(WORK SUPPORT)Display unitFactory
setting
Change seat sliding volume
settingThe distance at retain operation
can be selected from the following
3 modes.40 mm
—×
80 mm —
150 mm —
Change the Entry/Exit seat
slide function settingThe seat sliding turnout and return
at entry/exit can be selected: ON
(operated) – OFF (not operated)ON ON: Indicator lamp ON×
OFF OFF: Indicator lamp OFF —
Change the Entry/Exit tilt
steering wheel function settingLift up and backward steering
wheel at entry and exit can be
selected: ON (operated) - OFF (not
operated)ON ON: Indicator lamp ON×
OFF OFF: Indicator lamp OFF —
Reset custom settings All settings to default. —Default: Setting button
OFF—
Content Setting change operation Indicator LEDs
The seat sliding turnout and
steering wheel up/backward at
entry/exit can be operated.
Press the set switch for more than 10 secondsBlinking twice
The seat sliding turnout and
steering wheel up/backward at
entry/exit can be not operated.Blinking ones
Unit Power source Fuse/fusible link No.
BCMACC or ON power supply 6 (10A)
ON or STRAT power supply 1 (15A)
Battery power supply 22 (15A)
Battery power supply M (50A)
Page 4165 of 4449
SE-36
AUTOMATIC DRIVE POSITIONER
Revision: 2004 November 2004 FX35/FX45
2. CHECK POWER SUPPLY CIRCUIT (BCM)
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open and short between BCM and fuse or fusible link.
3. CHECK GROUND CIRCUIT (BCM)
1. Turn ignition switch OFF.
2. Check continuity between BCM connector and ground.
OK or NG
OK >> BCM circuit is OK. Check the driver seat control unit.
GO TO 4.
NG >> Repair or replace the harness between BCM and ground.
4. CHECK FUSE
Check 10A fuse [No.9, located in fuse block (J/B)].
NOTE:
Refer to SE-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 5.
NG >> If fuse is blownout, be sure to eliminate cause of malfunction before installing new fuse. Refer to
SE-15, "
Component Parts and Harness Connector Location" .
ConnectorTe r m i n a l s
(Wire color)Power
sourceConditionVoltage (V)
(Approx.)
(+) (–)
M311 (LG/R) GroundACC
power
supplyIgnition
switch
ACCBattery voltage
38 (W/L) GroundIgnition
power
supplyIgnition
switch
ONBattery voltage
B1442 (L/R)
55 (G)GroundBattery
power
supplyIgnition
switch
OFFBattery voltage
PIIA5083E
ConnectorTe r m i n a l s
(Wire color)
Condition Continuity
(+) (–)
B1449 (B)
52 (B)GroundIgnition switch
OFFContinuity should exist.
PIIA5084E