pg power INFINITI FX35 2004 Service Manual

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION WW
A
B
WW
Revision: 2004 November 2004 FX35/FX45
WIPER, WASHER & HORN
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
Components Parts and Harness Connector Loca-
tion ........................................................................... 4
System Description .................................................. 4
LOW SPEED WIPER OPERATION ...................... 5
HI SPEED WIPER OPERATION ........................... 5
INTERMITTENT OPERATION .............................. 5
AUTO STOP OPERATION .................................... 6
WASHER OPERATION ......................................... 6
MIST OPERATION ................................................ 6
FAIL-SAFE FUNCTION ......................................... 7
COMBINATION SWITCH READING FUNCTION ..... 7
CAN Communication System Description ................ 9
CAN Communication Unit ........................................ 9
Schematic .............................................................. 10
Wiring Diagram — WIPER — ................................. 11
Terminals and Reference Values for BCM ............. 14
Terminals and Reference Values for IPDM E/R ..... 15
How to Proceed With Trouble Diagnosis ................ 15
Preliminary Check .................................................. 16
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 16
CONSULT-II Functions (BCM) ............................... 17
CONSULT-II OPERATION .................................. 17
DATA MONITOR ................................................. 18
ACTIVE TEST ..................................................... 19
CONSULT-II Functions (IPDM E/R) ....................... 19
CONSULT-II OPERATION .................................. 19
SELF-DIAGNOSTIC RESULTS .......................... 20
DATA MONITOR ................................................. 20
ACTIVE TEST ..................................................... 21
Front Wiper Does Not Operate .............................. 21
Front Wiper Does Not Return to Stop Position ....... 24
Only Front Wiper LO Does Not Operate ................ 24Only Front Wiper HI Does Not Operate .................. 25
Only Front Wiper INT Does Not Operate ................ 25
Front Wiper Interval Time Is Not Controlled by Vehi-
cle Speed ................................................................ 26
Front Wiper Intermittent Operation Switch Position
Cannot Be Adjusted ................................................ 26
Wipers Do Not Wipe When Front Washer Operates ... 26
After Front Wipers Operate for 10 Seconds, They
Stop for 20 Seconds, and after repeating the oper-
ations five times, they become inoperative ............. 27
Front Wipers Do Not Stop ....................................... 28
Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location ............... 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
ADJUSTMENT .................................................... 29
Removal and Installation of Front Wiper Motor and
Linkage ................................................................... 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 29
Disassembly and Assembly of Front Wiper Motor
and Linkage ............................................................ 30
DISASSEMBLY ................................................... 30
ASSEMBLY ......................................................... 30
Washer Nozzle Adjustment .................................... 30
Washer Tube Layout .............................................. 32
Removal and Installation of Front Washer Nozzle ... 32
Removal and Installation of Front Washer Tube
Joint ........................................................................ 32
REMOVAL ........................................................... 32
INSTALLATION ................................................... 32
Check Valve Inspection .......................................... 32
Removal and Installation of Front Wiper and Washer
Switch ..................................................................... 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
Removal and Installation of Washer Tank .............. 33
REMOVAL ........................................................... 33

WW-2Revision: 2004 November 2004 FX35/FX45INSTALLATION .................................................... 34
Removal and Installation of Washer Motor ............. 34
REMOVAL ........................................................... 34
INSTALLATION .................................................... 34
REAR WIPER AND WASHER SYSTEM .................. 35
Component Parts and Harness Connector Location ... 35
System Description ................................................. 35
REAR WIPER OPERATION ................................ 35
INTERMITTENT OPERATION ............................ 36
AUTO STOP OPERATION .................................. 36
WASHER OPERATION ....................................... 36
BCM WIPER SWITCH READING FUNCTION .... 36
Wiring Diagram — WIP/ R — ................................. 37
Terminals and Reference Values for BCM .............. 39
How to Proceed With Trouble Diagnosis ................ 40
Preliminary Check .................................................. 40
INSPECTION POWER SUPPLY AND GROUND
CIRCUIT .............................................................. 40
CONSULT-II Functions ........................................... 41
CONSULT-II OPERATION ................................... 41
DATA MONITOR .................................................. 42
ACTIVE TEST ..................................................... 43
Rear Wiper Does Not Operate ............................... 43
Rear Wiper Does Not Return to Stop Position ........ 45
Only Rear Wiper ON Does Not Operate ................. 46
Only Rear Wiper INT Does Not Operate ................ 46
Wiper Does Not Wipe When Rear Washer Operates ... 46
Rear Wipers Do Not Stop ....................................... 46
Removal and Installation of Rear Wiper Arm, Adjust-
ment of Wiper Arms Stop Location ......................... 48
REMOVAL ........................................................... 48
INSTALLATION .................................................... 48
Removal and Installation of Rear Wiper Motor ....... 48
REMOVAL ........................................................... 49
INSTALLATION .................................................... 49
Removal and Installation of Rear Wiper Blade ....... 49REMOVAL ............................................................ 49
INSTALLATION .................................................... 49
Washer Nozzle Adjustment ..................................... 49
Removal and Installation of Washer Nozzle ........... 50
REMOVAL ............................................................ 50
INSTALLATION .................................................... 50
Washer Tube Layout ............................................... 50
Check Valve Inspection ........................................... 51
Removal and Installation of Rear Wiper and Washer
Switch ..................................................................... 51
Removal and Installation of Washer Tank ............... 51
Removal and Installation of Washer Pump ............. 51
CIGARETTE LIGHTER ............................................. 52
Wiring Diagram — CIGAR — .................................. 52
Removal and Installation of Cigarette Lighter ......... 53
REMOVAL ............................................................ 53
INSTALLATION .................................................... 53
POWER SOCKET ..................................................... 54
Wiring Diagram — P/SCKT — ................................ 54
Removal and Installation of Center Console Box
Rear Side Power Socket ......................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
Removal and Installation of Center Console Box
Power Socket .......................................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
Removal and Installation of Luggage Room Power
Socket ..................................................................... 55
REMOVAL ............................................................ 55
INSTALLATION .................................................... 55
HORN ........................................................................ 56
Wiring Diagram — HORN — .................................. 56
Removal and Installation ......................................... 57
REMOVAL ............................................................ 57
INSTALLATION .................................................... 57

PRECAUTION
WW-3
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONPFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS007KQ
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Wiring Diagrams and Trouble DiagnosisAKS0056N
When you read Wiring diagrams, refer to the following:

Refer to GI-15, "How to Read Wiring Diagrams" .

Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit.
When you perform trouble diagnosis, refer to the following:

Refer to GI-11, "How to Follow Trouble Diagnoses" .

Refer to GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" .

WW-4
FRONT WIPER AND WASHER SYSTEM
Revision: 2004 November 2004 FX35/FX45
FRONT WIPER AND WASHER SYSTEMPFP:28810
Components Parts and Harness Connector LocationAKS0056O
System DescriptionAKS0056P

All front wiper relays (HI, LO) are included in IPDM E/R.

Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input termi-
nals. Terminal combination status is read by BCM when switch is turned ON.

BCM controls front wiper LO, HI, and INT (intermittent) operation.

IPDM E/R operates wiper motor according to CAN communication signals from BCM.
Power is supplied at all times

through 50 A fusible link (letter M, located in fusible link block)

to BCM (body control module) terminal 55

through 15 A fuse [No. 22, located in fuse block (J/B)]

to BCM (body control module) terminal 42

through 30 A fuse [No. 73, located in IPDM E/R (intelligent power distribution module engine room)]

to front wiper relay [located in IPDM E/R (intelligent power distribution module engine room)]

through 15 A fuse [No. 78, located in IPDM E/R (intelligent power distribution module engine room)]

to CPU (central processing unit) [located in IPDM E/R (intelligent power distribution module engine room)]

through 10 A fuse [No. 71, located in IPDM E/R (intelligent power distribution module engine room)]

to CPU (central processing unit) [located in IPDM E/R (intelligent power distribution module engine
room)].
When the ignition switch ON or START position, power is supplied

through 15 A fuse [No. 1, located in fuse block (J/B)]

to BCM (body control module) terminal 38

through ignition relay [located in IPDM E/R (intelligent power distribution module engine room)]

to front wiper relay [located in IPDM E/R (intelligent power distribution module engine room)]
SKIA5289E

FRONT WIPER AND WASHER SYSTEM
WW-5
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2004 November 2004 FX35/FX45

to front wiper high relay [located in IPDM E/R (intelligent power distribution module engine room)]

through 10 A fuse [No. 84, located in IPDM E/R (intelligent power distribution module engine room)]

through IPDM E/R (intelligent power distribution module engine room) terminal 44

to front washer motor terminal 1.
Ground is supplied

to BCM terminals 49 and 52

through grounds M35, M45 and M85

to IPDM E/R terminals 38 and 60

through grounds E21, E50 and E51

to combination switch (wiper switch) terminal 12

through grounds M35, M45 and M85.
LOW SPEED WIPER OPERATION
When wiper switch is in LO position, BCM detects low speed wiper ON signal by BCM wiper switch reading
function.
BCM sends front wiper request signal (LO) with CAN communication line

from BCM terminals 39 and 40

to IPDM E/R terminals 48 and 49.
When IPDM E/R receives front wiper request signal (LO), it turns ON front wiper relay (located in IPDM E/R),
power is supplied

to front wiper motor terminal 1

through IPDM E/R terminal 21 and front wiper relay and front wiper HI relay.
Ground is supplied

to front wiper motor terminal 2

through grounds E21, E50 and E51.
With power and ground supplied, the front wiper motor operates at low speed.
HI SPEED WIPER OPERATION
When wiper switch is in HI position, BCM detects high speed wiper ON signal by BCM wiper switch reading
function.
BCM sends front wiper request signal (HI) with CAN communication line

from BCM terminals 39 and 40

to IPDM E/R terminals 48 and 49.
When IPDM E/R receives front wiper request signal (HI), it turns ON front wiper relay (located in IPDM E/R),
power is supplied

to front wiper motor terminal 4

through IPDM E/R terminal 31 and front wiper relay and front wiper HI relay.
Ground is supplied

to front wiper motor terminal 2

through grounds E21, E50 and E51.
With power and ground supplied, the front wiper motor operates at high speed.
INTERMITTENT OPERATION
Wiper intermittent operation delay interval is determined from a combination of 3 switches (intermittent opera-
tion dial position 1, intermittent operation dial position 2, and intermittent operation dial position 3) and vehicle
speed signal.
During each intermittent operation delay interval, BCM sends front wiper request signal to IPDM E/R.

FRONT WIPER AND WASHER SYSTEM
WW-15
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Values for IPDM E/RAKS0056V
How to Proceed With Trouble DiagnosisAKS0056W
1. Confirm the symptoms and customer complaint.
2. Understand operation description and function description. Refer to WW-4, "
System Description" .
3. Perform the Preliminary Check. Refer to WW-16, "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the front wiper and washer operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
35 (W/G) Combination switch output 2
ON

Lighting switch and wiper switch
OFF

Wiper dial position 4 36 (W/R) Combination switch output 1
38 (W/L) Ignition switch (ON) ON — Battery voltage
39 (L) CAN H — — —
40 (R) CAN L — — —
42 (L/R) Battery power supply OFF — Battery voltage
49 (B) Ground ON — Approx. 0 V
52 (B) Ground ON — Approx. 0 V
55 (G) Battery power supply OFF — Battery voltage Terminal No.
(Wire color)Signal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
SKIA5292E
Terminal No.
(Wire color)Signal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
21 (P) Low speed signal ON Wiper switchOFF Approx. 0 V
LO Battery voltage
31 (PU) High speed signal ON Wiper switchOFF Approx. 0 V
HI Battery voltage
32 (L) Wiper auto - stop signal ONWiper operating Battery voltage
Wiper stopped Approx. 0 V
38 (B) Ground ON — Approx. 0 V
44 (OR) Washer motor power supply ON — Battery voltage
48 (L) CAN H — — —
49 (R) CAN L — — —
60 (B) Ground ON — Approx. 0 V

WW-16
FRONT WIPER AND WASHER SYSTEM
Revision: 2004 November 2004 FX35/FX45
Preliminary CheckAKS0056X
CHECK POWER SUPPLY AND GROUND CIRCUIT
Inspection Procedure
1. CHECK FUSE

Check if wiper and washer fuse is blown.
Refer to WW-11, "Wiring Diagram — WIPER —" .
OK or NG
OK >> GO TO 2
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector terminal and
ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open or short between fuse, fusible link and BCM.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector M4 terminals 49
(B), 52 (B) and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Unit Power source Fuse and fusible link No.
Front washer motor Ignition switch ON or START 84
Front wiper motor, front wiper relay, front wiper HI relay Battery 73
BCMBatteryM
22
Ignition switch ON or START 1
Terminals Ignition switch position
(+)
(-) OFF ON
Connector Terminal (Wire color)
M4 42 (L/R)
GroundBattery voltage Battery voltage
M4 55 (G) Battery voltage Battery voltage
M3 38 (W/L) 0V Battery voltage
PKIA5190E
49 (B), 52 (B) - Ground : Continuity should exist.
PKIA5191E

FRONT WIPER AND WASHER SYSTEM
WW-21
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2004 November 2004 FX35/FX45
ACTIVE TEST
Operation Procedure
1. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2. Touch item to be tested, and check operation.
3. Touch “START”.
4. Touch “STOP” while testing to stop the operation.
Front Wiper Does Not OperateAKS0079W
CAUTION:

During IPDM E/R fail-safe control, front wipers may not operate. Refer to PG-18, "CAN COMMUNI-
CATION LINE CONTROL" in “PG IPDM E/R” to make sure that it is not in fail-safe status.
1. CHECK IPDM E/R TO FRONT WIPERS (1)
With CONSULT-ll
1. Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST”
on “SELECT DIAG MODE” screen.
2. Select “FRONT WIPER” on “SELECT TEST ITEM” screen.
Without CONSULT-ll
Start up auto active test. Refer to PG-24, "
Auto Active Test" .
Does the front wiper operate normally?
YES >> GO TO 6.
NO >> GO TO 2.
2. CHECK FUSE
1. Turn ignition switch OFF.
2. Check fuse No. 73 of IPDM E/R.
OK or NG
OK >> GO TO 3.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT" .
Test item CONSULT-II screen display Description
Front wiper (HI, LO) output FRONT WIPERWith a certain operation (OFF, HI ON, LO ON), the front wiper relay
(Lo, Hi) can be operated.
SKIA3486E

REAR WIPER AND WASHER SYSTEM
WW-35
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2004 November 2004 FX35/FX45
REAR WIPER AND WASHER SYSTEMPFP:28710
Component Parts and Harness Connector LocationAKS0057H
System DescriptionAKS0057I

Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input termi-
nals. Terminal combination status is read by BCM (body control module) when switch is turned ON.

BCM (body control module) controls rear wiper ON and INT (intermittent) operation.
Power supplied all time

through 50 A fusible link (letter M, located in fusible link block)

to BCM (body control module) terminal 55

through 15 A fuse [No. 22, located in fuse block (J/B)]

to BCM (body control module) terminal 42.
When ignition switch ON or START position, power is supplied

through 15 A fuse [No.1, located in fuse block (J/B)]

to BCM (body control module) terminal 38,

through 10 A fuse [No. 84, located in IPDM E/R (intelligent power distribution module engine room)]

to rear washer motor terminal 1.
Ground is supplied

to BCM (body control module) terminals 49 and 52

through grounds M35, M45 and M85

to combination switch (wiper switch) terminal 12

through grounds M35, M45 and M85.
REAR WIPER OPERATION
When wiper switch is in rear wiper ON position, BCM detects rear wiper ON signal by BCM wiper switch read-
ing function.
BCM operates rear wiper motor, power is supplied
SKIA5311E

WW-36
REAR WIPER AND WASHER SYSTEM
Revision: 2004 November 2004 FX35/FX45

through BCM terminal 70

to rear wiper motor 4.
Ground is supplied

to rear wiper motor terminal 2

through grounds B15 and B45.
With power and ground supplied, the rear wiper operates.
INTERMITTENT OPERATION
The rear wiper motor operates the wiper arms at low speed approximately every 7 seconds.
When wiper switch is in rear wiper INT position, BCM detects rear wiper INT signal by BCM wiper switch read-
ing function (Refer to BCS-3, "
COMBINATION SWITCH READING FUNCTION" ).
BCM operates rear wiper motor, power supplied

through BCM terminal 70

to rear wiper motor terminal 4.
Ground is supplied

to rear wiper motor terminal 2

through grounds B15 and B45.
With power and ground supplied, rear wiper operates at intermittent.
AUTO STOP OPERATION
With rear wiper switch turned OFF, rear wiper motor will continue to operate until wiper arm reaches rear wiper
stopper.
Then wiper motor turns the other way and wiper arm moves once until wiper arm reaches stopper.
WASHER OPERATION
When wiper switch is in rear wiper washer position, BCM detects rear wiper washer signal by BCM wiper
switch reading function (Refer to BCS-3, "
COMBINATION SWITCH READING FUNCTION" ), and combina-
tion switch (wiper switch) ground is supplied

to rear washer motor terminal 2

through combination switch (wiper switch) terminal 13

to combination switch (wiper switch) terminal 12

through grounds M35, M45 and M85.
With ground supplied, rear washer motor is operated.
When BCM detects that rear washer motor has operated for. 0.4 seconds or linger, BCM operates rear wiper
motor low speed.
When BCM detects washer switch is OFF, low speed operation cycles approximately 3 times and then stops.
BCM WIPER SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" in BODY CONTROL SYSTEM.