rear door INFINITI FX35 2004 User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: FX35, Model: INFINITI FX35 2004Pages: 4449, PDF Size: 99.66 MB
Page 637 of 4449
AV-46
AUDIO
Revision: 2004 November 2004 FX35/FX45
2. Remove screws (6) and remove A/C and AV switch from cluster
lid C.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation for Front Door SpeakerAKS005TQ
REMOVAL
1. Remove front door finisher. Refer to EI-35, "Removal and Instal-
lation" .
2. Remove screws (3) and remove door speaker.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation for Rear Door SpeakerAKS005TS
REMOVAL
1. Remove rear door finisher. Refer to EI-35, "Removal and Instal-
lation" .
2. Remove screws (3) and remove rear speaker.
INSTALLATION
Install in the reverse order of removal.
SKIA5802E
SKIA5803E
SKIA5804E
Page 797 of 4449
BCS-6
BCM (BODY CONTROL MODULE)
Revision: 2004 November 2004 FX35/FX45
BCM STATUS CONTROL
BCM changes its status depending on the operation status in order to save power consumption.
1. CAN communication status
With ignition switch ON, CAN communicates with other control units normally.
Control by BCM is being operated properly.
When ignition switch is OFF, switching to sleep mode is possible.
Even when ignition switch is OFF, if CAN communication with IPDM E/R and combination meter is
active, CAN communication status is active.
2. Sleep transient status
This status shuts down CAN communication when ignition switch is turned OFF.
It transmits sleep request signal to IPDM E/R and combination meter.
Two seconds after CAN communication of all control units stops, CAN communication switches to inac-
tive status.
3. CAN communication inactive status
With ignition switch OFF, CAN communication is not active.
With ignition switch OFF, control performed only by BCM is active.
Three seconds after CAN communication of all control units stops, CAN communication switches to
inactive status.
4. Sleep status
BCM is activated with low current consumption mode.
CAN communication is not active.
When CAN communication operation is detected, it switches to CAN communication status.
When a state of the following switches changes, it switches to CAN communication state.
–Key switch
–Hazard switch
–Door lock/unlock switch
–Front door switch (driver side, passenger side)
–Rear door switch (LH, RH)
–Back door opener switch
–Combination switch (passing, lighting switch 1st position, Front fog lamp)
–Key fob (lock/unlock signal)
–Key cylinder switch
When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.
Status of combination switch reading function is changed.
Page 798 of 4449
BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2004 November 2004 FX35/FX45
SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
System Reference
Power door lockBL-22, "
POWER DOOR LOCK SYSTEM"
Remote keyless entryBL-56, "REMOTE KEYLESS ENTRY SYSTEM"
Power window NOTEGW-15, "POWER WINDOW SYSTEM"
Sunroof NOTERF-10, "SUNROOF"
Room lamp timerLT-157, "INTERIOR ROOM LAMP"
Warning chimeDI-55, "WARNING CHIME"
Rear wiperWW-35, "REAR WIPER AND WASHER SYSTEM"
System Reference
Panic alarmBL-56, "
REMOTE KEYLESS ENTRY SYSTEM"
Theft warningBL-181, "VEHICLE SECURITY (THEFT WARNING) SYSTEM"
IVIS (NATS)BL-206, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)"
Headlamp, tail lamp, auto light system, battery saver control
LT- 7 , "HEADLAMP - XENON TYPE -"
LT-38, "DAYTIME LIGHT SYSTEM"
LT-54, "AUTO LIGHT SYSTEM"
Fog lampLT-77, "FRONT FOG LAMP"
Front wiperWW-4, "FRONT WIPER AND WASHER SYSTEM"
Rear window defoggerGW-86, "REAR WINDOW DEFOGGER"
System Reference
Warning chimeDI-55, "
WARNING CHIME"
Turn signal and hazard warning lampsLT-89, "TURN SIGNAL AND HAZARD WARNING LAMPS"
System Reference
Intelligent KeyBL-84, "
INTELLIGENT KEY SYSTEM"
Page 799 of 4449
BCS-8
BCM (BODY CONTROL MODULE)
Revision: 2004 November 2004 FX35/FX45
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote control entry system key fob
All-door locking actuator
Turn signal lamp (LH, RH)
Power door lock system
Power window main switch
(door lock and unlock switch)
Power window sub switch (passenger side)
(door lock and unlock switch)All-door locking actuator
Power supply (IGN) to power window, sunroof Ignition power supply Power window and sunroof system
Power supply (BAT) to power window, sunroof
and power seatBattery power supplyPower window, sunroof system and
power seat
Panic alarm
Key switch
Key fobIPDM E/R
Theft warning system
All-door switch
Hood switch
Key fob
Power window main switch (door lock and
unlock switch)
IPDM E/R
Security indicator lamp
Auto light system
Optical sensor
Combination switchIPDM E/R
Battery saver control
Ignition switch
Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch
Turn signal lamp
Combination meter
Hazard lamp Hazard switch
Turn signal lamp
Combination meter
Room lamp timer
Key switch
key fob
Power window main switch (door lock and
unlock switch)
Front door switch driver side
All-door switchInterior room lamp
Key warning chime
Key switch
Front door switch driver sideCombination meter
(warning buzzer)
Light warning chime
Combination switch
Front door switch driver sideCombination meter
(warning buzzer)
Seat belt warning chime
Combination meter (Seat belt buckle
(driver side) switch)
Ignition switchCombination meter
(warning buzzer)
Vehicle-speed-sensing intermittent wiper
Combination switch
Combination meterIPDM E/R
Rear intermittent wiper Combination switch Rear wiper motor
Rear window defogger
Rear window defogger switch
Ignition switchIPDM E/R
A/C switch signal Unified meter and A/C amp. ECM
Blower fan switch signal Unified meter and A/C amp. ECM
Page 804 of 4449
BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2004 November 2004 FX35/FX45
4. Select the desired part to be diagnosed on the “SELECT TEST
ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will Only display systems the vehicle possesses.
×:Applicable
NOTE:
This item is indicated, but it is what it does not use.
SKIA4963E
System and item CONSULT-II displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSDATA
MONI-
TORCAN
DIAG
SUP-
PORT
MNTRECU
PA R T
NUM-
BERACTIVE
TESTCON-
FIGU-
RATION
Power door lock system DOOR LOCK×× ×
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×× ×
Remotecontrol entry system MULTI REMOTE ENT×× ×
Headlamp HEAD LAMP×× ×
Wiper WIPER××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch signal
A/C switch signalAIR CONDITONER×
Intelligent Key system INTELLIGENT KEY×
Combination switch COMB SW×
BCM BCM× × ×××
×
Note
IVIS IMMU××
Room lamp battery saver BATTERY SAVER×× ×
Trunk lid
NoteTRUNK××
Vehicle security system THEFT ALM×× ×
Retained power control RETAINED PWR×× ×
Oil pressure switch SIGNAL BUFFER××
Page 809 of 4449
BL-2Revision: 2004 November 2004 FX35/FX45Trouble Diagnosis Chart by Symptom .................... 41
Check Door Switch ................................................. 42
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) ............................................................. 42
CHECK BACK DOOR SWITCH .......................... 44
Check Key Switch ................................................... 46
Check Door Lock and Unlock Switch ..................... 48
Check Door Lock Actuator (Driver side) ................. 50
Check Door Lock Actuator (Passenger Side and
Rear LH/RH) ........................................................... 51
Check Fuel Lid Opener Actuator ............................ 52
Check Front Door Key Cylinder Switch (Lock) ....... 53
Check Front Door Key Cylinder Switch (Unlock) .... 54
Check Select Unlock Relay Circuit ......................... 55
REMOTE KEYLESS ENTRY SYSTEM ..................... 56
Component Parts and Harness Connector Location ... 56
System Description ................................................. 57
INPUTS ............................................................... 57
OPERATED PROCEDURE ................................. 58
CAN Communication System Description .............. 59
CAN Communication Unit ....................................... 59
Schematic ............................................................... 60
Wiring Diagram — KEYLES— ................................ 61
FIG. 1 ................................................................... 61
FIG. 2 ................................................................... 62
FIG. 3 ................................................................... 63
Terminals and Reference Value for BCM ................ 64
Terminals and Reference Value for IPDM E/R ........ 65
CONSULT-II Function ............................................. 65
CONSULT-II INSPECTION PROCEDURE .......... 65
CONSULT-II APPLICATION ITEMS .................... 66
Work Flow ............................................................... 68
Trouble Diagnosis Chart by Symptom .................... 69
Check Key Fob Battery and Function ..................... 71
Check ACC Switch ................................................. 72
Check Door Switch ................................................. 73
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) ............................................................. 73
CHECK BACK DOOR SWITCH .......................... 75
Check Key Switch ................................................... 77
Check IPDM E/R Operation .................................... 78
Check Hazard Function .......................................... 79
Check Horn Function .............................................. 79
Check Headlamp Function ..................................... 79
Check Map Lamp and Ignition Keyhole Illumination
Function .................................................................. 79
ID Code Entry Procedure ....................................... 80
KEY FOB ID SET UP WITH CONSULT-II ........... 80
KEY FOB ID SET UP WITHOUT CONSULT-II .... 82
Key Fob Battery Replacement ................................ 83
INTELLIGENT KEY SYSTEM ................................... 84
Component Parts and Harness Connector Location ... 84
System Description ................................................. 86
DOOR LOCK FUNCTION ................................... 86
REMOTE CONTROL ENTRY FUNCTIONS ........ 87
ENGINE STARTUP FUNCTION .......................... 88
WARNING AND ALARM FUNCTION .................. 89
CHANGE SETTINGS FUNCTION ....................... 92
INTELLIGENT KEY REGISTRATION .................. 92STEERING LOCK UNIT REGISTRATION ........... 92
CAN Communication System Description .............. 93
CAN Communication Unit ....................................... 93
Schematic ............................................................... 94
Wiring Diagram — I/KEY— ..................................... 96
Terminals and Reference Value for INTELLIGENT
KEY UNIT .............................................................109
Terminals and Reference Value for Steering Lock
unit ........................................................................ 111
Terminals and Reference Value for BCM .............. 111
Terminals and Reference Value for IPDM E/R ......112
Diagnosis Procedure .............................................113
WORK FLOW ....................................................113
CONSULT-II Functions .........................................114
CONSULT-II Inspection Procedure .......................114
BASIC OPERATION ..........................................114
CONSULT-II Application Items ..............................115
WORK SUPPORT .............................................115
SELF-DIAGNOSTIC RESULTS .........................115
DATA MONITOR ................................................115
ACTIVE TEST ....................................................116
List of Operation Related Parts .............................117
Trouble Diagnosis Symptom Chart .......................118
ALL FUNCTIONS OF THE INTELLIGENT KEY
ARE NOT OPERATING .....................................118
REMOTE CONTROL ENTRY FUNCTION MAL-
FUNCTION ........................................................118
DOOR LOCK FUNCTION MALFUNCTION .......119
ENGINE START FUNCTION MALFUNCTION ..120
WARNING CHIME FUNCTION MALFUNCTION .120
Check CAN Communication System Inspection ...123
Check Intelligent Key Unit Power Supply and
Ground Circuit .......................................................124
Check Key Switch (Intelligent Key Unit Input) .......124
Check Key Switch (BCM Input) .............................126
Check Ignition Knob Switch ..................................127
Check Door Switch ...............................................128
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) ............................................................128
CHECK BACK DOOR SWITCH .........................129
Check Unlock Sensor ...........................................131
Check Door Request Switch .................................132
Check Intelligent Key Warning Buzzer ..................134
Check Outside Key Antenna .................................135
Check Inside Key Antenna ....................................138
Check Steering Lock Unit ......................................139
Check Stop Lamp Switch ......................................141
Check Detention Switch ........................................142
Check Select Unlock Relay ...................................144
Check Hazard Function ........................................145
Check Horn Function ............................................145
Check Headlamp Function ....................................145
Check IPDM E/R Operation ..................................145
Removal and Installation of Intelligent Key Unit ....146
REMOVAL ..........................................................146
INSTALLATION ..................................................146
Intelligent Key Inspection ......................................147
INTELLIGENT KEY DISASSEMBLY AND
Page 810 of 4449
BL-3
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45ASSEMBLY ....................................................... 147
REMOTE CONTROLLER BATTERY INSPEC-
TION .................................................................. 147
DOOR ..................................................................... 148
Fitting Adjustment ................................................ 148
FRONT DOOR .................................................. 148
REAR DOOR .................................................... 148
STRIKER ADJUSTMENT ................................. 149
Removal and Installation of Front Door ................ 149
REMOVAL ......................................................... 149
INSTALLATION ................................................. 150
Removal and Installation of Rear Door ................ 150
REMOVAL ......................................................... 150
INSTALLATION ................................................. 151
Removal and Installation of Door Weathers trip ... 151
REMOVAL ......................................................... 151
INSTALLATION ................................................. 151
FRONT DOOR LOCK ............................................. 152
Removal and Installation ...................................... 152
REMOVAL ......................................................... 152
INSTALLATION ................................................. 154
Disassembly and Assembly ................................. 155
DOOR KEY CYLINDER ASSEMBLY ................ 155
REAR DOOR LOCK ............................................... 156
Removal and Installation ...................................... 156
REMOVAL ......................................................... 156
INSTALLATION ................................................. 158
BACK DOOR .......................................................... 159
Fitting Adjustment ................................................ 159
VERTICAL/LATERAL CLEARANCE ADJUST-
MENT ................................................................ 159
Back Door Assembly ............................................ 159
REMOVAL ......................................................... 159
INSTALLATION ................................................. 160
INSPECTION .................................................... 160
Removal and Installation of Back Door Striker ..... 160
REMOVAL ......................................................... 160
INSTALLATION ................................................. 160
Removal and Installation of Back Door Stay ........ 161
REMOVAL ......................................................... 161
INSTALLATION ................................................. 161
Removal and Installation of Dave Tail Male &
Female ................................................................. 161
REMOVAL ......................................................... 161
Removal and Installation of Back Door Weatherstrip . 162
REMOVAL ......................................................... 162
INSTALLATION ................................................. 162
BACK DOOR LOCK ASSEMBLY .......................... 163
Removal and Installation of Back Door Lock & Clo-
sure Assembly ...................................................... 163
REMOVAL ......................................................... 163
INSTALLATION ................................................. 163
INSPECTION .................................................... 163
Removal and Installation of Back Door Opener
Switch ................................................................... 163
REMOVAL ......................................................... 163
INSTALLATION ................................................. 164
Disassembly and Assembly ................................. 164
BACK DOOR LOCK & CLOSURE ASSEMBLY . 164BACK DOOR AUTO CLOSURE SYSTEM .............165
Component Parts and Harness Connector Location .165
System Description ...............................................165
CLOSE OPERATION ........................................165
NON-OPERATION CONDITION .......................165
OPEN OPERATION ..........................................166
Wiring Diagram — B/CLOS — .............................167
Terminals and Reference Value for Back Door Clo-
sure Control Unit ...................................................169
Work Flow .............................................................170
Preliminary Check ................................................170
Trouble Diagnosis Chart by Symptom ..................170
Back Door Closure Control Unit Power Supply and
Ground Circuit Check ...........................................171
Half-Latch Switch Check ......................................171
Close Switch Check ..............................................173
Open Switch Check ..............................................174
Back Door Opener Switch Check (With Intelligent
Key) ......................................................................175
Back Door Opener Switch Check (Without Intelli-
gent Key) ..............................................................177
Unlock Sensor Check (Without Intelligent Key) ....179
Closure Motor Check ............................................180
Removal and Installation of Back Door Closer Con-
trol Unit .................................................................180
VEHICLE SECURITY (THEFT WARNING) SYSTEM .181
Component Parts and Harness Connector Location .181
System Description ...............................................182
DESCRIPTION ..................................................182
POWER SUPPLY ..............................................183
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ...................................................................183
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ................................................................184
VEHICLE SECURITY SYSTEM DEACTIVATION .184
PANIC ALARM OPERATION ............................184
CAN Communication System Description ............185
CAN Communication Unit .....................................185
Schematic .............................................................186
Wiring Diagram -VEHSEC- ...................................187
Terminals and Reference Value for BCM .............192
Terminals and Reference Value for IPDM E/R .....192
CONSULT-II Inspection Procedure .......................193
CONSULT-II APPLICATION ITEM ....................194
Trouble Diagnosis .................................................195
WORK FLOW ....................................................195
Preliminary Check ................................................196
Trouble Diagnosis Symptom Chart .......................197
Diagnostic Procedure 1 ........................................198
1 – 1 DOOR SWITCH CHECK ..........................198
1 – 2 HOOD SWITCH CHECK ..........................200
1 – 3 BACK DOOR SWITCH CHECK ...............202
Diagnostic Procedure 2 ........................................204
SECURITY INDICATOR LAMP CHECK ...........204
Diagnostic Procedure 3 ........................................205
FRONT DOOR KEY CYLINDER SWITCH
CHECK ..............................................................205
Diagnostic Procedure 4 ........................................205
VEHICLE SECURITY HORN ALARM CHECK . 205
Page 811 of 4449
BL-4Revision: 2004 November 2004 FX35/FX45Diagnostic Procedure 5 ........................................205
VEHICLE SECURITY HEADLAMP ALARM
CHECK ..............................................................205
Diagnostic Procedure 6 ........................................205
DOOR LOCK AND UNLOCK SWITCH CHECK .205
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ......................................................................206
Component Parts and Harness Connector Location .206
System Description ...............................................206
DESCRIPTION ..................................................206
SECURITY INDICATOR ....................................207
System Composition .............................................208
ECM Re-communicating Function ........................208
Wiring Diagram – NATS – .....................................209
MODELS WITH INTELLIGENT KEY SYSTEM . 209
MODELS WITHOUT INTELLIGENT KEY SYS-
TEM ...................................................................211
Terminals and Reference Value for Steering Lock
Unit/with Intelligent Key System ...........................212
Terminals and Reference Value for Intelligent Key
Unit/with Intelligent Key System ...........................212
Terminals and Reference Value for BCM ..............213
CONSULT-II ..........................................................214
CONSULT-II INSPECTION PROCEDURE ........214
CONSULT-II DIAGNOSTIC TEST MODE FUNC-
TION ..................................................................215
HOW TO READ SELF-DIAGNOSTIC RESULTS .215
NATS SELF-DIAGNOSTIC RESULT ITEM
CHART ..............................................................216
Diagnosis Procedure ............................................217
WORK FLOW ....................................................217
Trouble Diagnosis Symptom Chart .......................218
Security Indicator Inspection ................................218
Diagnostic Procedure 1 ........................................219
Diagnostic Procedure 2 ........................................220
Diagnostic Procedure 3 ........................................221
Diagnostic Procedure 4 ........................................222
Diagnostic Procedure 5 ........................................223
Diagnostic Procedure 6 ........................................224
Diagnostic Procedure 7 ........................................226
Removal and Installation NATS Antenna Amp. ....227
REMOVAL .........................................................227
INSTALLATION ..................................................227
INTEGRATED HOMELINK TRANSMITTER ...........228Wiring Diagram —TRNSCV— ..............................228
Trouble Diagnoses ................................................229
DIAGNOSTIC PROCEDURE .............................229
BODY REPAIR ........................................................231
Body Exterior Paint Color ......................................231
Body Component Parts .........................................232
UNDERBODY COMPONENT PARTS ...............232
BODY COMPONENT PARTS ............................234
Corrosion Protection .............................................236
DESCRIPTION ..................................................236
ANTI-CORROSIVE WAX ...................................237
UNDERCOATING ..............................................238
STONE GUARD COAT ......................................239
Body Sealing .........................................................240
DESCRIPTION ..................................................240
Body Construction .................................................243
BODY CONSTRUCTION ...................................243
Body Alignment .....................................................244
BODY CENTER MARKS ...................................244
PANEL PARTS MATCHING MARKS .................245
DESCRIPTION ..................................................246
ENGINE COMPARTMENT ................................247
UNDERBODY ....................................................249
PASSENGER COMPARTMENT ........................251
REAR BODY ......................................................253
Handling Precautions For Plastics ........................255
HANDLING PRECAUTIONS FOR PLASTICS ..255
LOCATION OF PLASTIC PARTS ......................256
Precautions In Repairing High Strength Steel .......258
HIGH STRENGTH STEEL (HSS) USED IN NIS-
SAN VEHICLES .................................................258
Replacement Operations ......................................261
DESCRIPTION ..................................................261
HOODLEDGE ....................................................264
FRONT SIDE MEMBER ....................................266
FRONT SIDE MEMBER (PARTIAL REPLACE-
MENT) ................................................................268
FRONT PILLAR .................................................270
CENTER PILLAR ...............................................272
OUTER SILL ......................................................274
REAR FENDER .................................................276
REAR PANEL ....................................................278
REAR END CROSSMEMBER ...........................280
REAR FLOOR REAR .........................................282
REAR SIDE MEMBER EXTENSION .................285
Page 831 of 4449
BL-24
POWER DOOR LOCK SYSTEM
Revision: 2004 November 2004 FX35/FX45
Then key cylinder switch operation signal (lock) is supplied
to BCM terminal 22
through power window main switch terminal 14.
When the door is unlocked with key cylinder switch, ground is supplied
to power window main switch terminal 6
through key cylinder switch terminal 6 and 5
through grounds M35, M45 and M85.
Then key cylinder switch operation signal (unlock) is supplied
to BCM terminal 22
through power window main switch terminal 14.
BCM is connected to power window main switch and front power window switch (passenger side) as serial
link.
When the front door switch (driver side) is ON (door is OPEN), ground is supplied
to BCM terminal 62
through front door switch (driver side) terminal 1
through front door switch (driver side) case ground.
When the front door switch (passenger side) is ON (door is OPEN), ground is supplied
to BCM terminal 12
through front door switch (passenger side) terminal 1
through front door switch (passenger side) case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied
to BCM terminal 63
through front door switch LH terminal 1
through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied
to BCM terminal 13
through front door switch RH terminal 1
through rear door switch RH case ground.
When the back door switch is ON (door is OPEN), ground is supplied
to BCM terminal 58
through back door closure motor (door switch) terminal 7 and 8
through grounds B15 and B45.
OUTLINE
Functions Available by Operating the Door Lock and Unlock Switches on Driver's Door and
Passenger's Door
Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors and
fuel lid lock actuator are locked.
Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors
and fuel lid lock actuator are unlocked.
Functions Available by Operating the Key Cylinder Switch on Driver's
Interlocked with the locking operation of door key cylinder, door lock actuators of all doors and fuel lid lock
actuator are locked.
Select Unlock Operation
When door key cylinder is unlocked, door lock actuator driver side and fuel lid lock actuator are unlocked.
When door key cylinder is unlocked for the second time within 5 seconds after the first operation, door
lock actuators on all doors are unlocked.
Select unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK
SUPPORT”. Refer to BL-40, "
Work Support" .
Select unlock operation mode can be changed also on the display.
Refer toAV- 5 8 , "
SETTING SCREEN" . (without navigation system)
Page 844 of 4449
POWER DOOR LOCK SYSTEM
BL-37
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for BCMAIS004LV
Terminals and Reference Value for Intelligent Key Unit (With Intelligent Key Sys-
tem)
AIS004LW
Work FlowAIS004LX
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to BL-23, "
System Description" .
3. Perform the preliminary check. Refer to BL-38, "
Preliminary Check" .
4. According to the trouble diagnosis chart by symptom, repair or replace the cause of the malfunction.
Refer to BL-41, "
Trouble Diagnosis Chart by Symptom" .
5. Does power door lock system operate normally?
YES: GO TO 6.
NO: GO TO 4.
6. INSPECTION END
TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
Approx.
12 P/BFront door switch (Passenger
side)ON (door open) → OFF (door closed) 0 → Battery voltage
13 P/L Rear door switch RH ON (door open) → OFF (door closed) 0 → Battery voltage
22 OR Power window serial link Ignition switch ON
37 B/W Key switchON (Key inserted) → OFF (Key removed
from IGN key cylinder)Battery voltage → 0
39 L CAN H — —
40 R CAN L — —
42 L/R Battery power supply (fuse) — Battery voltage
44 YDriver door lock actuator
(unlock)Door lock / unlock switch
(Free → Unlock)0 → Battery voltage
49, 52 B Ground — 0
50 PU Door lock actuator (lock)Door lock / unlock switch
(Free → Lock)0 → Battery voltage
51 W/BPassenger and rear doors lock
actuator (unlock)Door lock / unlock switch
(Free → Unlock)0 → Battery voltage
55 G Power source (Fusible link) — Battery voltage
58 L Back door switch ON (Door open) → OFF (Door closed) 0 → 9
62 W Front door switch (Driver side) ON (Door open) → OFF (Door closed) 0 → Battery voltage
63 P Rear door switch LH ON (Door open) → OFF (Door closed) 0 → Battery voltage
PIIA2344J
TERMI-
NALWIRE
COLORITEM CONDITIONVOLTAGE (V)
Approx.
2 L CAN H – –
3 R CAN L – –
27 L/W Push switch Push switch (OFF → ON) 0 → Battery voltage
40 BR/W AS unlock output signalDoor lock / unlock switch
(Free → Unlock)0 → Battery voltage