fuel INFINITI FX35 2004 Owner's Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: FX35, Model: INFINITI FX35 2004Pages: 4449, PDF Size: 99.66 MB
Page 1264 of 4449
COMBINATION METERS
DI-21
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2004 November 2004 FX35/FX45
4. CHECK FUEL LEVEL SENSOR (MAIN·SUB) CIRCUIT
1. Disconnect fuel level sensor unit and fuel pump (main) connector.
2. Check continuity between fuel level sensor unit (sub) harness
connector B40 terminal 2 (Y) and fuel level sensor unit and fuel
pump (main) harness connector B39 terminal 2 (Y).
3. Check continuity between fuel level sensor unit (sub) harness
connector B40 terminal 2 (Y) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK FUEL LEVEL SENSOR (MAIN) CIRCUIT
1. Check continuity between fuel level sensor unit and fuel pump
(main) harness connector B39 terminal 5 (B) and unified meter
and A/C amp. harness connector M56 terminal 36 (B/W).
2. Check continuity between fuel level sensor unit and fuel pump
(main) harness connector B39 terminal 5 (B) and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK INSTALLATION CONDITION
Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the
internal components in the fuel tank.
OK or NG
OK >> Replace unified meter and A/C amp. Refer to DI-34, "Removal and Installation of Unified Meter
and A/C Amp." .
NG >> Install the fuel level sensor unit properly.
Fuel Level Sensor Signal Inspection 2AKS005MZ
The following symptoms do not indicate a malfunction.
LOW-FUEL WARNING LAMP
Depending on vehicle position or driving circumstance, the fuel in the tank flows and the warning lamp ON tim-
ing may change.
1. CHECK FUEL GAUGE
Check if fuel gauge is normally operating.
YES >> Replace combination meter.
NO >> Go to DI-20, "
Fuel Level Sensor Signal Inspection 1" . Continuity should exist.
Continuity should not exist.
SKIA5204E
Continuity should exist.
Continuity should not exist.
SKIA5205E
Page 1267 of 4449
DI-24
COMBINATION METERS
Revision: 2004 November 2004 FX35/FX45
8. CHECK VOLTAGE SIGNAL OF UNIFIED METER AND A/C AMP.
1. Turn ignition switch OFF and connect unified meter and A/C amp. connector.
2. Turn ignition switch ON.
3. Check voltage signal between combination meter harness con-
nector M20 terminal 14 (PU) and ground with simple oscillo-
scope of CONSULT-II.
OK or NG
OK >> Replace combination meter.
NG >> Replace unified meter and A/C amp. Refer to DI-34, "
Removal and Installation of Unified Meter
and A/C Amp." .
Odo/Trip Meter and Illumination Control Switch InspectionAKS005N2
1. CHECK ODO/TRIP METER AND ILLUMINATION CONTROL SWITCH
1. Remove odo/trip meter and illumination control switch. Refer to DI-27, "
Removal and Installation of Odo/
Trip Meter and Illumination Control Switch" .
2. Check continuity between odo/trip meter and illumination control
switch harness connector terminals 25, 26, 35 or 36 and 27.
OK or NG
OK >> Replace combination meter.
NG >> Replace odo/trip meter and illumination control switch.
Fuel Gauge Pointer Fluctuates, Indicator Wrong Value or VariesAKS005N3
1. CHECK FUEL GAUGE FLUCTUATION
Test drive vehicle to see if gauge fluctuates only during driving or before or after stopping.
Does the indication value vary only during driving or before or after stopping?
YES >> The pointer fluctuation may be caused by fuel level change in the fuel tank. Condition is normal.
NO >> Ask the customer about the situation when the symptom occurs in detail, and perform the trouble
diagnosis. 14 (PU) - Ground:
SKIA9260ESKIA3362E
Terminal Condition Continuity
26
27Illumination control switch (+) is pushed. Yes
Illumination control switch (+) is released. No
25Illumination control switch (–) is pushed. Yes
Illumination control switch (–) is released. No
36Trip transfer switch is pushed. Yes
Trip transfer switch is released. No
35Trip reset switch is pushed. Yes
Trip reset switch is released. No
SKIA4846E
Page 1268 of 4449
COMBINATION METERS
DI-25
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2004 November 2004 FX35/FX45
Fuel Gauge Does Not Move to FULL positionAKS005N4
1. QUESTION 1
Does it take a long time for the pointer to move to FULL position?
YES >> GO TO 2.
NO >> GO TO 3.
2. QUESTION 2
Was the vehicle fueled with the ignition switch ON?
YES >> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time to move
to FULL position because of the characteristic of the fuel gauge.
NO >> GO TO 3.
3. QUESTION 3
Is the vehicle parked on an incline?
YES >> Check the fuel level indication with vehicle on a level surface.
NO >> GO TO 4.
4. QUESTION 4
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES >> Check the fuel level sensor unit. Refer to DI-25, "CHECK FUEL LEVEL SENSOR UNIT" .
NO >> The float arm may interfere or bind with any of the components in the fuel tank.
Electrical Components InspectionAKS005N5
CHECK FUEL LEVEL SENSOR UNIT
For removal, refer to FL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY" .
Check Fuel Level Sensor Unit and Fuel Pump (Main)
1. Check the resistance between terminals 2 and 5.
*1 and *2: When float rod is in contact with stopper.
2. If the results of check is NG, check the fuel level sensor unit and
fuel pump (main) harness.
Check Fuel Level Sensor Unit and Pump (Main) Harness
1. Check continuity at following terminals.
2. If the results of check is NG, replace fuel pump assembly. If the
results of check is OK, replace fuel level sensor unit.
Terminal
Float position mm (in)Resistance
value Ω
(+) (−)
25*1 Empty 29 (1.14) Approx. 80
*2 Full 236 (9.29) Approx. 3
PKIA1936E
Terminal Continuity
2 - Signal terminal
Ye s
5 - Ground terminal
SKIA3582E
Page 1269 of 4449
DI-26
COMBINATION METERS
Revision: 2004 November 2004 FX35/FX45
Check Fuel Level Sensor Unit (Sub)
Check resistance between terminals 1 and 2.
*1 and *2: When float rod is in contact with stopper.
Removal and InstallationAKS005N6
COMBINATION METER ASSEMBLY
Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
Disassembly and Assembly for Combination MeterAKS007G1
DISASSEMBLY
1. Remove screws (3) and remove rear cover.
2. Disconnect odo/trip meter and illumination control switch con-
nector.
Terminal
Float position mm (in)Resistance
valueΩ
(+) (−)
12*1 Full 6 (0.24) Approx. 3
*2 Empty 203 (7.99) Approx. 48
PKIA1937E
1. Rear cover 2. Screws 3. Plate
4. Unified meter control unit assembly 5. Front cover 6. Reinforcing metal
7. Switch and meter housing
SKIA5790E
SKIA5792E
Page 1271 of 4449
DI-28
UNIFIED METER AND A/C AMP
Revision: 2004 November 2004 FX35/FX45
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionAKS005N8
For the unified meter and A/C amp., the signal required for controlling the combination meter are inte-
grated in the A/C auto amp.
Unified meter and A/C amp. controls each operation for A/C auto amp. For information regarding A/C con-
trol, refer to AT C - 3 0 , "
AIR CONDITIONER CONTROL" in ATC section.
Unified meter and A/C amp. inputs necessary information for combination meter from each unit by CAN
communication and so on.
And unified meter and A/C amp. outputs these signals using communication line (TX, RX) between unified
meter and A/C amp. and combination meter.
The signals required for the distance to empty (DTE) display are centralized in the unified meter and A/C
amp., converted into data, and sent to the display unit (without NAVI) display control unit (with NAVI) using
CAN communication.
Other input signals are also sent to the ECM, TCM, AWD control unit, BCM, display unit (without NAVI)
and display control unit (with NAVI) using CAN communication.
The unified meter and A/C amp. have a CONSULT-II function (self-diagnostic results, CAN diagnostic
support monitor, data monitor).
INPUT/OUTPUT SIGNALS
Between Unified Meter & A/C amp. and Combination Meter
Unit Input Output
Unified meter and A/C amp.
Seat belt buckle switch signal (Driver's side)
Parking brake signal
Illumination control nighttime required signal
Refuel status signal
Low-fuel warning lamp condition signal
Combination meter receive error signal
Delivery destination data signal
Combination meter specifications signal
Vehicle speed signal (8-pulse)
Engine speed signal
Engine coolant temperature signal
Fuel level sensor signal (resistance value)
Malfunction indicator lamp signal
ABS warning lamp signal
Low tire pressure warning lamp signal
Brake warning lamp signal
A/T CHECK warning lamp signal
ICC warning lamp signal
Oil pressure switch signal
Door switch signal
AWD warning lamp signal
VDC OFF indicator lamp signal
SLIP indicator lamp signal
ASCD CRUISE indicator lamp signal
ASCD SET indicator lamp signal
High beam request signal
Turn indicator signal
Snow mode switch signal
ICC system display signal
A/T position indicator signal
Manual mode indicator signal
Manual mode gear position signal
CAN communication condition signal of A/T
Position lights request signal
Buzzer output signal
Page 1272 of 4449
UNIFIED METER AND A/C AMP
DI-29
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2004 November 2004 FX35/FX45
FA I L - S A F E
Solution When Communication Error Between the Unified Meter & A/C Amp. and the Combi-
nation Meter
CAN Communication System DescriptionAKS007Z1
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007YX
Refer to LAN-6, "CAN Communication Unit" in “LAN SYSTEM”.
Function Specifications
Speedometer
Reset to zero by suspending communication. Tachometer
Fuel gauge
Water temperature gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
A/T position indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lampABS warning lamp
The lamp turns on by suspending communication. VDC OFF indicator
SLIP indicator
Brake warning lamp
Door warning lamp
The lamp turns off by suspending communication. Low tire pressure warning lamp
ASCD SET indicator lamp
ASCD CRUISE indicator lamp
AWD warning lamp
ICC warning lamp
A/T CHECK warning lamp
Oil pressure warning lamp
Snow mode indicator lamp
Turn signal indicator
Malfunction indicator lamp
High beam indicator
Page 1276 of 4449
UNIFIED METER AND A/C AMP
DI-33
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2004 November 2004 FX35/FX45
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
SKIA4957E
Display item [Unit] MAIN SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] or [mph] X XThis is the angle correction value after the speed signal
from the ABS actuator and electric unit (control unit) is
converted into the vehicle speed.
SPEED OUTPUT [km/h] or [mph] X XThis is the angle correction value before the speed signal
from the ABS actuator and electric unit (control unit) is
converted into the vehicle speed.
TACHO METER [rpm] X XThis is the converted value for the engine speed signal
from the ECM.
W TEMP METER [°C] or [°F] X XThis is the converted value for the engine coolant temper-
ature signal from the ECM.
FUEL METER [lit.] X XThis is the processed value for the signal (resistance
value) from the fuel gauge.
DISTANCE [km] or [mile] X XThis is the calculated value for the speed signal from the
ABS actuator and electric unit (control unit), the signal
(resistance signal) from the fuel gauge and fuel consump-
tion signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
MIL [ON/OFF] XIndicates [ON/OFF] condition of malfunction indicator
lamp.
AIR PRES W/L [ON/OFF] XIndicates [ON/OFF] condition of low tire pressure warning
lamp.
SEAT BELT W/L [ON/OFF] X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
VDC/TCS IND [ON/OFF] X Indicates [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Indicates [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (green).
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of key knob warning lamp.
M RANGE SW [ON/OFF] X XIndicates [ON/OFF] condition of manual mode range
switch.
NM RANGE SW [ON/OFF] X XIndicates [ON/OFF] condition of except for manual mode
range switch.
Page 1342 of 4449
EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: 2004 November 2004 FX35/FX45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
Alphabetical Index .................................................. 15
DTC No. Index ....................................................... 19
PRECAUTIONS ........................................................ 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 23
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 23
Precaution .............................................................. 23
Wiring Diagrams and Trouble Diagnosis ................ 26
PREPARATION ......................................................... 27
Special Service Tools ............................................. 27
Commercial Service Tools ...................................... 28
ENGINE CONTROL SYSTEM .................................. 29
System Diagram ..................................................... 29
Vacuum Hose Drawing ........................................... 30
System Chart ......................................................... 31
Multiport Fuel Injection (MFI) System .................... 32
Electronic Ignition (EI) System ............................... 34
Air Conditioning Cut Control ................................... 35
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 35
CAN communication .............................................. 36
BASIC SERVICE PROCEDURE .............................. 37
Idle Speed and Ignition Timing Check .................... 37
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................. 38
Accelerator Pedal Released Position Learning ...... 49
Throttle Valve Closed Position Learning ................ 49
Idle Air Volume Learning ........................................ 49
Fuel Pressure Check .............................................. 51
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 53
Introduction ............................................................ 53
Two Trip Detection Logic ........................................ 53
Emission-Related Diagnostic Information .............. 54
IVIS (Infiniti Vehicle Immobilizer System — NATS) ... 68
Malfunction Indicator Lamp (MIL) ........................... 68
OBD System Operation Chart ................................ 72TROUBLE DIAGNOSIS ............................................ 77
Trouble Diagnosis Introduction ............................... 77
DTC Inspection Priority Chart ................................. 80
Fail-Safe Chart ....................................................... 82
Basic Inspection ..................................................... 83
Symptom Matrix Chart ............................................ 88
Engine Control Component Parts Location ............ 92
Circuit Diagram ....................................................... 98
ECM Harness Connector Terminal Layout ...........100
ECM Terminals and Reference Value ...................100
CONSULT-II Function ...........................................109
Generic Scan Tool (GST) Function .......................122
CONSULT-II Reference Value in Data Monitor .....125
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................129
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .131
Description ............................................................131
Testing Condition ..................................................131
Inspection Procedure ............................................131
Diagnostic Procedure ...........................................132
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................135
Description ............................................................135
Diagnostic Procedure ...........................................135
POWER SUPPLY AND GROUND CIRCUIT ...........136
Wiring Diagram .....................................................136
Diagnostic Procedure ...........................................137
Ground Inspection ................................................141
DTC U1000, U1001 CAN COMMUNICATION LINE .142
Description ............................................................142
On Board Diagnosis Logic ....................................142
DTC Confirmation Procedure ...............................142
Wiring Diagram .....................................................143
Diagnostic Procedure ...........................................144
DTC P0011, P0021 IVT CONTROL ........................145
Description ............................................................145
CONSULT-II Reference Value in Data Monitor Mode
.145
On Board Diagnosis Logic ....................................146
Page 1344 of 4449
EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45Diagnostic Procedure ........................................... 232
Component Inspection ......................................... 234
Removal and Installation ...................................... 235
DTC P0138, P0158 HO2S2 .................................... 236
Component Description ........................................ 236
CONSULT-II Reference Value in Data Monitor Mode
. 236
On Board Diagnosis Logic ................................... 236
DTC Confirmation Procedure ............................... 237
Wiring Diagram .................................................... 238
Diagnostic Procedure ........................................... 241
Component Inspection ......................................... 243
Removal and Installation ...................................... 244
DTC P0139, P0159 HO2S2 .................................... 245
Component Description ........................................ 245
CONSULT-II Reference Value in Data Monitor Mode
. 245
On Board Diagnosis Logic ................................... 245
DTC Confirmation Procedure ............................... 246
Overall Function Check ........................................ 246
Wiring Diagram .................................................... 248
Diagnostic Procedure ........................................... 251
Component Inspection ......................................... 253
Removal and Installation ...................................... 255
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION .............................................................. 256
On Board Diagnosis Logic ................................... 256
DTC Confirmation Procedure ............................... 256
Wiring Diagram .................................................... 258
Diagnostic Procedure ........................................... 260
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION .............................................................. 265
On Board Diagnosis Logic ................................... 265
DTC Confirmation Procedure ............................... 265
Wiring Diagram .................................................... 267
Diagnostic Procedure ........................................... 269
DTC P0181 FTT SENSOR ...................................... 273
Component Description ........................................ 273
On Board Diagnosis Logic ................................... 273
DTC Confirmation Procedure ............................... 273
Wiring Diagram .................................................... 275
Diagnostic Procedure ........................................... 276
Component Inspection ......................................... 277
Removal and Installation ...................................... 278
DTC P0182, P0183 FTT SENSOR ......................... 279
Component Description ........................................ 279
On Board Diagnosis Logic ................................... 279
DTC Confirmation Procedure ............................... 279
Wiring Diagram .................................................... 280
Diagnostic Procedure ........................................... 281
Component Inspection ......................................... 282
Removal and Installation ...................................... 283
DTC P0222, P0223 TP SENSOR ........................... 284
Component Description ........................................ 284
CONSULT-II Reference Value in Data Monitor Mode
. 284
On Board Diagnosis Logic ................................... 284
DTC Confirmation Procedure ............................... 285
Wiring Diagram .................................................... 286Diagnostic Procedure ...........................................287
Component Inspection ..........................................290
Removal and Installation ......................................290
DTC P0300 - P0306 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 6 CYLINDER MISFIRE .....................291
On Board Diagnosis Logic ....................................291
DTC Confirmation Procedure ...............................291
Diagnostic Procedure ...........................................292
DTC P0327, P0328 KS ...........................................297
Component Description ........................................297
On Board Diagnosis Logic ....................................297
DTC Confirmation Procedure ...............................297
Wiring Diagram .....................................................298
Diagnostic Procedure ...........................................299
Component Inspection ..........................................300
Removal and Installation ......................................301
DTC P0335 CKP SENSOR (POS) ..........................302
Component Description ........................................302
CONSULT-II Reference Value in Data Monitor Mode
.302
On Board Diagnosis Logic ....................................302
DTC Confirmation Procedure ...............................302
Wiring Diagram .....................................................303
Diagnostic Procedure ...........................................304
Component Inspection ..........................................307
Removal and Installation ......................................307
DTC P0340, P0345 CMP SENSOR (PHASE) ........308
Component Description ........................................308
CONSULT-II Reference Value in Data Monitor Mode
.308
On Board Diagnosis Logic ....................................308
DTC Confirmation Procedure ...............................308
Wiring Diagram .....................................................309
Diagnostic Procedure ...........................................312
Component Inspection ..........................................315
Removal and Installation ......................................315
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ........................................................................316
On Board Diagnosis Logic ....................................316
DTC Confirmation Procedure ...............................316
Overall Function Check ........................................317
Diagnostic Procedure ...........................................318
DTC P0441 EVAP CONTROL SYSTEM .................321
System Description ...............................................321
On Board Diagnosis Logic ....................................321
DTC Confirmation Procedure ...............................321
Overall Function Check ........................................322
Diagnostic Procedure ...........................................323
DTC P0442 EVAP CONTROL SYSTEM .................326
On Board Diagnosis Logic ....................................326
DTC Confirmation Procedure ...............................327
Diagnostic Procedure ...........................................328
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ......................335
Description ............................................................335
CONSULT-II Reference Value in Data Monitor Mode
.335
On Board Diagnosis Logic ....................................336
DTC Confirmation Procedure ...............................336
Page 1345 of 4449
EC-4Revision: 2004 November 2004 FX35/FX45Wiring Diagram .....................................................337
Diagnostic Procedure ...........................................339
Component Inspection ..........................................340
Removal and Installation ......................................341
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE .....................................................................342
Component Description ........................................342
CONSULT-II Reference Value in Data Monitor Mode
.342
On Board Diagnosis Logic ....................................342
DTC Confirmation Procedure ...............................343
Wiring Diagram .....................................................344
Diagnostic Procedure ...........................................345
Component Inspection ..........................................347
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR ..................................................................349
Component Description ........................................349
CONSULT-II Reference Value in Data Monitor Mode
.349
On Board Diagnosis Logic ....................................349
DTC Confirmation Procedure ...............................350
Diagnostic Procedure ...........................................350
Component Inspection ..........................................351
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ..................................................................352
Component Description ........................................352
CONSULT-II Reference Value in Data Monitor Mode
.352
On Board Diagnosis Logic ....................................352
DTC Confirmation Procedure ...............................353
Wiring Diagram .....................................................354
Diagnostic Procedure ...........................................355
Component Inspection ..........................................357
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ..................................................................358
Component Description ........................................358
CONSULT-II Reference Value in Data Monitor Mode
.358
On Board Diagnosis Logic ....................................358
DTC Confirmation Procedure ...............................359
Wiring Diagram .....................................................360
Diagnostic Procedure ...........................................361
Component Inspection ..........................................365
DTC P0455 EVAP CONTROL SYSTEM .................366
On Board Diagnosis Logic ....................................366
DTC Confirmation Procedure ...............................367
Diagnostic Procedure ...........................................368
DTC P0456 EVAP CONTROL SYSTEM .................374
On Board Diagnosis Logic ....................................374
DTC Confirmation Procedure ...............................375
Overall Function Check ........................................376
Diagnostic Procedure ...........................................377
DTC P0460 FUEL LEVEL SENSOR .......................384
Component Description ........................................384
On Board Diagnosis Logic ....................................384
DTC Confirmation Procedure ...............................384
Diagnostic Procedure ...........................................385
Removal and Installation ......................................385DTC P0461 FUEL LEVEL SENSOR .......................386
Component Description ........................................386
On Board Diagnosis Logic ....................................386
Overall Function Check .........................................386
Diagnostic Procedure ............................................387
Removal and Installation .......................................387
DTC P0462, P0463 FUEL LEVEL SENSOR ...........388
Component Description ........................................388
On Board Diagnosis Logic ....................................388
DTC Confirmation Procedure ................................388
Diagnostic Procedure ............................................389
Removal and Installation .......................................389
DTC P0500 VSS ......................................................390
Description ............................................................390
On Board Diagnosis Logic ....................................390
DTC Confirmation Procedure ................................390
Overall Function Check .........................................390
Diagnostic Procedure ............................................391
DTC P0506 ISC SYSTEM .......................................392
Description ............................................................392
On Board Diagnosis Logic ....................................392
DTC Confirmation Procedure ................................392
Diagnostic Procedure ............................................393
DTC P0507 ISC SYSTEM .......................................394
Description ............................................................394
On Board Diagnosis Logic ....................................394
DTC Confirmation Procedure ................................394
Diagnostic Procedure ............................................395
DTC P0550 PSP SENSOR ......................................396
Component Description ........................................396
CONSULT-II Reference Value in Data Monitor Mode
.396
On Board Diagnosis Logic ....................................396
DTC Confirmation Procedure ................................396
Wiring Diagram .....................................................397
Diagnostic Procedure ............................................398
Component Inspection ..........................................400
Removal and Installation .......................................400
DTC P0605 ECM .....................................................401
Component Description ........................................401
On Board Diagnosis Logic ....................................401
DTC Confirmation Procedure ................................401
Diagnostic Procedure ............................................402
DTC P1065 ECM POWER SUPPLY ........................404
Component Description ........................................404
On Board Diagnosis Logic ....................................404
DTC Confirmation Procedure ................................404
Wiring Diagram .....................................................405
Diagnostic Procedure ............................................406
D T C P1111, P 1136 IVT CONTROL SOLENOID
VALVE ......................................................................408
Component Description ........................................408
CONSULT-II Reference Value in Data Monitor Mode
.408
On Board Diagnosis Logic ....................................408
DTC Confirmation Procedure ................................408
Wiring Diagram .....................................................409
Diagnostic Procedure ............................................412