Memory INFINITI FX35 2005 Owners Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 4351 of 4731
RF-12
SUNROOF
Revision: 2005 July 2005 FX
ANTI-PINCH FUNCTION
The CPU of sunroof motor monitors the sunroof motor operation and the sunroof position (fully-closed or
other) by the signals from sunroof motor.
When sunroof motor detects an interruption during the following slide close and tilt down operation, sunroof
switch controls the motor for open and the sunroof will operate until full up position (when tilt down operate) or
125 mm (4.92 in) or more in an open direction (when slide close operate).
close operation and tilt down when ignition switch is in the ON position.
close operation and tilt down during retained power operation.
MEMORY RESET PROCEDURE
1. Please observe the following instructions while confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops. (to wipe-out the memory of lid position and operating friction.)
2. Initialization of system should be conducted after the following conditions.
When the battery is out or connector is disconnected while sunroof is operating or within 5 seconds
after sunroof stops.
When the sunroof motor is changed.
When an emergency handle is used.
When the sunroof does not operate normally. (Incomplete initialization conditions)
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Close the sunroof if it is not in the closed position. It may be necessary to repeatedly push the switch to close the sunroof.
2. Press and hold the TILT UP switch. Do not release the switch, keep pressure on it. After 10 seconds of depressing, the sunroof will tilt up, then tilt down. Release the button.
3. Press and hold the TILT UP switch again. Do not release the switch, keep pressure on it. While depress- ing the switch, the sunroof will “Slide open” “Slide close” “Tilt up” “Tilt down”. Release the button after the
sunroof “Tilts down” and stops.
4. Initializing procedure is complete. Confirm proper operation of the sunroof (slide open, slide close, tilt up, tilt down.)
Page 4474 of 4731
SE-1
SEAT
I BODY
CONTENTS
C
D E
F
G H
J
K L
M
SECTION SE
A
B
SE
Revision: 2005 July 2005 FX
SEAT
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Service Notice ..................................................... ..... 3
PREPARATION ...................................................... ..... 4
Special Service Tools .......................................... ..... 4
Commercial Service Tools ................................... ..... 4
SQUEAK AND RATTLE TROUBLE DIAGNOSIS . ..... 5
Work Flow ........................................................... ..... 5
CUSTOMER INTERVIEW ................................ ..... 5
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 6
CHECK RELATED SERVICE BULLETINS ...... ..... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 6
REPAIR THE CAUSE ...................................... ..... 6
CONFIRM THE REPAIR .................................. ..... 7
Generic Squeak and Rattle Troubleshooting ...... ..... 7
INSTRUMENT PANEL ..................................... ..... 7
CENTER CONSOLE ........................................ ..... 7
DOORS ............................................................ ..... 7
TRUNK ............................................................. ..... 8
SUNROOF/HEADLINING ................................ ..... 8
SEATS .............................................................. ..... 8
UNDERHOOD .................................................. ..... 8
Diagnostic Worksheet ......................................... ..... 9
AUTOMATIC DRIVE POSITIONER ....................... ....11
System Description ............................................. .... 11
MANUAL OPERATION .................................... .... 11
AUTOMATIC OPERATION .............................. .... 11
MEMORY STORING AND KEY FOB INTER-
LOCK STORING .............................................. ... 12
MEMORY SWITCH OPERATION .................... ... 13
ENTRY OPERATION ....................................... ... 13
EXITING OPERATION ..................................... ... 13
KEY FOB INTERLOCK OPERATION .............. ... 14
FAIL- SAFE MODE .......................................... ... 14
CANCEL OF FAIL-SAFE MODE ...................... ... 14
Component Parts and Harness Connector Location ... 15
CAN Communication System Description ........... ... 16 CAN Communication Unit ....................................
... 16
Schematic ............................................................ ... 17
Wiring Diagram —AUT/DP— .............................. ... 19
Terminals and Reference Values for BCM ........... ... 30
Terminals and Reference Values for Automatic
Drive Positioner Control Unit ............................... ... 30
Terminals and Reference Values for Driver Seat
Control Unit .......................................................... ... 32
Work Flow ............................................................ ... 35
Preliminary Check ............................................... ... 35
SETTING CHANGE FUNCTION ...................... ... 35
CHECK POWER SUPPLY AND GROUND ...... ... 36
CONSULT-II Function (AUTO DRIVE POS.) ....... ... 38
CONSULT-II INSPECTION PROCEDURE ....... ... 38
SELF-DIAGNOSIS RESULTS .......................... ... 39
DATA MONITOR .............................................. ... 40
ACTIVE TEST .................................................. ... 41
Check CAN Communication System Inspection . ... 42
Symptom Chart .................................................... ... 42
Sliding Motor Circuit Check ................................. ... 43
Reclining Motor Circuit Check ............................. ... 45
Front Lifting Motor Circuit Check ......................... ... 46
Rear Lifting Motor Circuit Check .......................... ... 48
Telescopic Motor Circuit Check ........................... ... 49
Tilt Motor Circuit Check ....................................... ... 50
Driver Side Mirror Motor Circuit Check ................ ... 52
Passenger Side Mirror Motor Circuit Check ........ ... 53
Sliding Sensor Circuit Check ............................... ... 55
Reclining Sensor Circuit Check ........................... ... 56
Front Lifting Sensor Circuit Check ....................... ... 57
Rear Lifting Sensor Circuit Check ....................... ... 58
Telescopic Sensor Circuit Check ......................... ... 59
Tilt Sensor Circuit Check ..................................... ... 60
Driver Side Mirror Sensor Circuit Check .............. ... 61
Passenger Side Mirror Sensor Circuit Check ...... ... 63
Steering and Door Mirror Sensor Power and Ground
Circuit Check ....................................................... ... 65
Front Door Switch (Driver Side) Circuit Check .... ... 66
Sliding Switch Circuit Check ................................ ... 68
Reclining Switch Check ....................................... ... 69
Page 4475 of 4731
SE-2Revision: 2005 July 2005 FX
Front Lifting Switch Circuit Check ........................
... 71
Rear Lifting Switch Circuit Check ........................ ... 72
Sliding Switch and Reclining Switch Ground Circuit
Check .................................................................. ... 73
Front Lifting Switch and Rear Lifting Switch Ground
Circuit Check ....................................................... ... 74
Telescopic Switch Circuit Check .......................... ... 74
Tilt Switch Circuit Check ...................................... ... 76
Door Mirror Remote Control Switch (Changeover
Switch) Circuit Check .......................................... ... 78
Door Mirror Remote Control Switch (Mirror Switch)
Circuit Check ....................................................... ... 80
Detention Switch (P Range Switch) Circuit Check ... 82
Key Switch and Key Lock Solenoid Circuit Check
(With Intelligent Key) ........................................... ... 83
Key Switch Circuit Check (Without Intelligent Key) ... 85
Seat Memory Switch Circuit Check ..................... ... 86
Memory Indicator Lamp Circuit Check ................. ... 88
Uart Communication Line Circuit Check .............. ... 89
Lumber Support Circuit Check ............................ ... 90
POWER SEAT ........................................................ ... 92
Schematic ............................................................ ... 92
Wiring Diagram–SEAT– / For Driver Seat ........... ... 93
Wiring Diagram–SEAT– / For Passenger Seat .... ... 95
Trouble Diagnosis ................................................ ... 96 HEATED SEAT .......................................................
... 97
Description ........................................................... ... 97
Wiring Diagram – HSEAT – ................................. ... 98
FRONT SEAT ......................................................... .100
Removal and Installation ...................................... .100
REMOVAL ......................................................... .102
INSTALLATION ................................................. .103
REMOVAL OF SEATBACK TRIM AND PAD .... .103
INSTALLATION OF SEATBACK TRIM AND PAD .104
REMOVAL OF SEAT CUSHION TRIM AND PAD .104
INSTALLATION OF SEAT CUSHION TRIM AND
PAD ................................................................... .105
REAR SEAT ............................................................ .106
Removal and Installation ...................................... .106
REMOVAL ......................................................... .108
INSTALLATION ................................................. .108
REMOVAL OF SEAT CUSHION TRIM AND PAD .108
INSTALLATION OF SEAT CUSHION TRIM AND
PAD ................................................................... .109
REMOVAL OF SEATBACK TRIM AND PAD .... .109
INSTALLATION OF SEATBACK TRIM AND PAD .109
REMOVAL OF REMOTE CONTROL LEVER ... .110
INSTALLATION OF REMOTE CONTROL
LEVER .............................................................. .110
Page 4484 of 4731
AUTOMATIC DRIVE POSITIONER SE-11
C
D E
F
G H
J
K L
M A
B
SE
Revision: 2005 July 2005 FX
AUTOMATIC DRIVE POSITIONERPFP:28491
System Description AIS002XB
The system automatically moves the driver seat to facilitate entry/exit to/from the vehicle. The automatic
drive positioner control unit can also store the optimum driving positions (driver seat, pedal position and
door mirror position) for 2 people. If the driver is changes, one-touch operation allows changing to the
other driving position.
The settings (ON/OFF) of the automatic sliding seat (Entry/Exiting operation) at entry/exit can be changed
as desired, using the display unit in the center of the instrument panel. The set content is transmitted by
CAN communication, from display unit (without NAVI) or display control unit (with NAVI) to driver seat con-
trol unit.
Using CONSULT-II, the seat slide amount at entry/exit setting can be changed.
MANUAL OPERATION
The driving position [seat position, steering wheel position (tilt, telescopic) and door mirror position] can be
adjusted with the power seat switch or ADP steering switch or door mirror remote control switch.
NOTE:
The seat can be manually operated with the ignition switch OFF.
The door mirrors can be manually operated with the ignition switch turned ACC or ON.
A U T O M AT I C O P E R AT I O N
NOTE:
Disconnecting the battery erases the stored memory.
After connecting the battery, insert the key into the ignition cylinder and turn the driver door switch ON (open) →OFF (close) →ON
(open), the Entry/ Exiting operation becomes possible.
After exiting operation is carried out, return operation can be operated.
NOTE:
During automatic operation, if the ignition switch is turned ON →START, the automatic operation is suspended. When the ignition switch
returns to ON, it resumes. Function Description
Memory switch operation The seat, steering and door mirror move to the stored driving position by pushing
memory switch (1 or 2).
Entry/Exiting function Exiting operation At exit, the seat moves backward and steering wheel moves forward/upward.
Entry operation
At entry, the seat and steering wheel returns from the exiting position to the previous
driving position.
Key fob interlock operation Perform memory operation, exiting operation and entry operation by pressing key fob
unlock button.
Auto operation temporary stop
conditions. When ignition switch turned to START during memory switch operation and return opera-
tion, memory switch operation and entry operation is stopped.
Auto operation stop conditions.
When the vehicle speed becomes 7 km/h (4 MPH) or higher.
When the setting switch, memory switch 1, or 2 are pressed.
When A/T selector lever is in any position other than P.
When the door mirror remote control switch is operated (when ignition switch turned to
ON or ACC).
When power seat switch turned ON.
When ADP steering switch turned ON (telescopic operation or tilt operation).
When door mirror operates (only memory switch operation).
When driver seat sliding Entry/Exiting setting is OFF (only entry/exiting operation).
When steering wheel tilt and telescopic Entry/Exiting setting is OFF (only entry/exiting
operation).
When the tilt and telescopic sensor malfunction is detected.
Page 4485 of 4731
SE-12
AUTOMATIC DRIVE POSITIONER
Revision: 2005 July 2005 FX
MEMORY STORING AND KEY FOB INTERLOCK STORING
Store the 2 driving positions and shifts to the stored driving position with the memory switch.
Key fob interlock function is set simultaneously with setting driving position memory. It can set driving
position to memory position.
NOTE:
If another key fob inter lock function setting is performed by same key, newly registered setting is valid.
If new memory string is performed to memory switch that already set key fob interlock function, key fob
interlock function setting is reset.
If key does not set previously, key fob interlock function cannot set.
PIIB3487E
Page 4486 of 4731
AUTOMATIC DRIVE POSITIONER SE-13
C
D E
F
G H
J
K L
M A
B
SE
Revision: 2005 July 2005 FX
MEMORY SWITCH OPERATION
Selecting the memory
NOTE:
The driver's seat position and steering adjustment functions (see the following table) operate simultaneously in
the order of priority.
*: In conjunction with sliding the seat, the door mirrors are positioned.
ENTRY OPERATION
When the seat are on the exiting positions, the following operation moves the seat to the previous position
before the exiting operation.
EXITING OPERATION
At exit, the seat are automatically moved to the exiting position.
Priority Function Priority Function
1 Seat sliding, door mirror LH/RH* 4 Seat reclining
2 Steering wheel telescoping 5 Seat lifter-FR
3 Steering wheel tilt 6 Seat lifter-RR
PIIA6137E
PIIA6135E
PIIA6136E
Page 4487 of 4731
SE-14
AUTOMATIC DRIVE POSITIONER
Revision: 2005 July 2005 FX
KEY FOB INTERLOCK OPERATION
Perform memory operation, exiting operation and entry operation by pressing key fob unlock button.
NOTE:
If steering wheel operation is cancelled, the system performs seat and mirror operation only.
If Entry/Exiting operation is cancelled, the system performs steering wheel operation and mirror operation
only.
If ignition switch turns ON in the middle of memory operation, the system does not perform exiting opera-
tion after memory operation.
If ignition switch turns ON in the middle of exiting operation, entry operation starts at that time.
FAIL - SAFE MO DE
When any manual and automatic operations are not performed, if any motor operations of seats or tilt of steer-
ing are detected for approx. 0.1 sec or more, status is judged “Output malfunction”. Motor operation will be
suspended automatically, and all automatic operations will be ineffective (in this case, the motor will not oper-
ate manually).
CANCEL OF FAIL-SAFE MODE
The mode is cancelled when the selector lever is shifted to P position from any other position.
PIIA6949E
OPERATED PORTION Seat sliding
Seat reclining
Seat lifting (Front)
Seat lifting (Rear)
steering tilt
steering telescopic
Page 4503 of 4731
SE-30
AUTOMATIC DRIVE POSITIONER
Revision: 2005 July 2005 FX
Terminals and Reference Values for BCMAIS002XG
Terminals and Reference Values for Automatic Drive Positioner Control UnitAIS002XH
TERMINAL WIRE
COLOR ITEM CONDITION
VOLTAGE (V)
(Approx.)
11 LG/R Ignition switch (ACC) Ignition switch
(ACC or ON position) Battery voltage
37 B/W Key switch signal Key switch ON (key is inserted in
ignition key cylinder) Battery voltage
Key switch OFF (key is removed
from ignition key cylinder) 0
38 W/L Ignition switch (ON) Ignition switch
(ON or START position) Battery voltage
39 L CAN-H — —
40 R CAN-L — —
42 L/R Power source (Fuse) — Battery voltage
49 B Ground (signal) — 0
52 B Ground (power) — 0
55 G Power supply (Fusible link) — Battery voltage
62 W Front door switch (driver side) ON (Open) → OFF (Closed) 0 → Battery voltage
TERMI-
NAL WIRE
COLOR ITEM CONDITION VOLTAGE (V)
(Approx.)
1 LG/R Tilt switch UP signal Tilt switch turned to upward 0
Other than above 5
2 G/W Changeover switch RH signal When changeover switch in RH posi-
tion 0
Other than above 5
3 GY Mirror switch UP signal When mirror switch in turned to
upward position 0
Other than above 5
4 Y Mirror switch LEFT signal When mirror switch in turned to left-
ward position 0
Other than above 5
5OR Passenger side mirror sensor
(vertical) signal When passenger side mirror motor is
UP or DOWN operation Changes between 3 (close to perk)
- 1 (close to valley)
6P/L Driver side mirror sensor
(vertical) signal When driver side mirror motor is UP
or DOWN operation Changes between 3 (close to perk)
- 1 (close to valley)
7 Y/R Tilt sensor signal Tilt position, top 2
Tilt position, bottom 4
10 B UART LINE (TX) Memory switch 1 or 2 operated
11 B R Telescopic switch
FORWARD signal Telescopic switch turned to forward 0
Other than above 5
PIIA4813E
Page 4504 of 4731
AUTOMATIC DRIVE POSITIONER SE-31
C
D E
F
G H
J
K L
M A
B
SE
Revision: 2005 July 2005 FX
14 L/W Passenger side mirror motor
UP signal When passenger side mirror motor
UP operation 1.5 - Battery voltage
Other than above 0
15 L/B Passenger side mirror motor
LEFT signal When passenger side mirror motor
LEFT operation 1.5 - Battery voltage
Other than above 0
16 P Driver side mirror motor
DOWN signal When driver side mirror motor DOWN
operation 1.5 - Battery voltage
Other than above 0
Driver side mirror motor
RIGTH signal When driver side mirror motor RIGHT
operation 1.5 - Battery voltage
Other than above 0
17 R/B Tilt switch DOWN signal Tilt switch turned to downward 0
Other than above 5
18 L/OR Changeover switch LH signal When changeover switch in LH posi-
tion 0
Other than above 5
19 GY/L Mirror switch DOWN signal When mirror switch in turned to down-
ward position 0
Other than above 5
20 PU Mirror switch RIGHT signal When mirror switch in turned to right-
ward position 0
Other than above 5
21 G/Y Passenger side mirror sensor
(horizontal) signal When passenger side mirror motor is
LEFT or RIGHT operation Changes between 1 (close to left
edge) - 3 (close to right edge)
22 L/Y Driver side mirror sensor
(horizontal) signal When driver side mirror motor is LEFT
or RIGHT operation Changes between 1 (close to right
edge) - 3 (close to left edge)
23 Y/B Telescopic sensor input Telescopic position, top 1
Telescopic position, bottom 4
26 W UART LINE (RX) Memory switch 1 or 2 operated
27 LG Telescopic switch
BACKWARD signal Telescopic switch turned to backward 0
Other than above 5
28 SB Ignition switch (START) Ignition switch
(START position) Battery voltage
30 W/R Passenger side mirror motor
DOWN signal When passenger side mirror motor
downward 1.5 - Battery voltage
Other than above 0
Passenger side mirror motor
RIGTH signal When passenger side mirror motor
RIGHT operation 1.5 - Battery voltage
Other than above 0
31 R/W Driver side mirror motor
UP signal When driver side mirror motor upward 1.5 - Battery voltage
Other than above 0
TERMI-
NAL WIRE
COLOR ITEM CONDITION VOLTAGE (V)
(Approx.)
PIIA4814E
Page 4505 of 4731
SE-32
AUTOMATIC DRIVE POSITIONER
Revision: 2005 July 2005 FX
Terminals and Reference Values for Driver Seat Control UnitAIS002XI
32 G/B Driver side mirror motor
LEFT signal When driver side mirror motor LEFT
operation 1.5 - Battery voltage
Other than above 0
33 G/W Sensor power supply — 5
34 L/R Battery power supply — Battery voltage
35 R/L Tilt motor UP signal Tilt switch turned to upward Battery voltage
Other than above 0
36 L/R Telescopic motor
FORWARD signal Telescopic switch turned to forward Battery voltage
OFF 0
39 W/R Battery power supply — Battery voltage
40 B Ground (signal) — 0
41 B/Y Sensor ground — 0
42 R/B Tilt motor DOWN signal Tilt switch turned to downward Battery voltage
Other than above 0
44 L/W Telescopic motor
BACKWARD signal Telescopic switch turned to backward Battery voltage
Other than above 0
48 B Ground (power) — 0
TERMI-
NAL WIRE
COLOR ITEM CONDITION VOLTAGE (V)
(Approx.)
TERMI-NAL WIRE
COLOR ITEM CONDITION VOLTAGE (V)
(Approx.)
1A R Power source (Fusible link) — Battery voltage
2 P UART LINE (TX) Memory switch 1 or 2 operated
3G Sliding motor
FORWARD signal When sliding motor
FORWARD operation Battery voltage
Other than above 0
4 G/L Reclining motor
FORWARD signal When reclining motor
FORWARD operation Battery voltage
Other than above 0
5LG Front lifting motor
DOWN signal When front lifting motor
DOWN operation Battery voltage
Other than above 0
6 G/W Rear lifting motor
UP signal When rear lifting motor
UP operation Battery voltage
Other than above 0
7 G/B Rear lifting motor
DOWN signal When rear lifting motor
DOWN operation Battery voltage
Other than above 0
PIIA4814E