engine oil INFINITI FX35 2005 Owner's Manual

AT-80
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
40
Slips/Will
Not
Engage While accelerating in
4th, engine races or
slippage occurs. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. ATF pressure switch 3 and input clutch solenoid valve AT- 1 7 7,
AT- 1 5 0
6. Control valve with TCM AT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assemblyAT- 3 0 8
9. Input clutchAT- 3 1 3
10. Gear systemAT- 2 7 8
11. High and low reverse clutchAT- 3 2 3
12. Direct clutchAT- 3 2 6
41 While accelerating in
5th, engine races or
slippage occurs. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5,
AT- 1 5 4
6. Control valve with TCM AT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assembly AT- 3 0 8
9. Front brake (brake band)AT- 2 9 0
10. Input clutchAT- 3 1 3
11. Gear systemAT- 2 7 8
12. High and low reverse clutchAT- 3 2 3
42 Slips at lock-up. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Engine speed signalAT- 1 2 3
4. Turbine revolution sensorAT- 1 4 1
5. Torque converter clutch solenoid valveAT- 1 2 5
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Torque converter
AT- 2 9 09. Oil pump assemblyAT- 3 0 8
No. Items Symptom Condition Diagnostic Item Reference
page

AT-84
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
53
Others Shift point is low in “D”
position. ON vehicle 1. Vehicle speed sensor A/T and vehicle speed sensor MTR
AT- 11 8
,
AT- 1 4 3
2. Accelerator pedal position sensor AT- 1 3 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
54 Judder occurs during
lock-up. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. Turbine revolution sensorAT- 1 4 1
4. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
5. Accelerator pedal position sensor AT- 1 3 3
6. CAN communication lineAT- 1 0 6
7. Torque converter clutch solenoid valveAT- 1 2 5
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Torque converter AT- 2 9 0
55 Strange noise in “R”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 0
6. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
8. High and low reverse clutchAT- 3 2 3
9. Reverse brakeAT- 2 9 0
56 Strange noise in “N”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 06. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
No. Items Symptom Condition Diagnostic Item Reference
page

TROUBLE DIAGNOSIS AT-85
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX57
Others Strange noise in “D”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT-123
3. CAN communication lineAT-106
4. Control valve with TCMAT-243
OFF vehicle 5. Torque converter
AT-290
6. Oil pump assemblyAT-308
7. Gear systemAT-278
8. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT-19, "Cross-
Sectional View (AWD Models)" ) AT-290
58 Vehicle does not
decelerate by engine
brake.
Refer to AT-231,
"Vehicle Does Not
Decelerate by Engine
Brake" . ON vehicle
1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 5AT-179
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Input clutch
AT-3139. High and low reverse clutchAT-323
10. Direct clutchAT-326
59 Engine brake does
not work M5 → M4. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 1AT-175
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Front brake (brake band) AT-290
60 Engine brake does
not work M4 → M3. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 1 and ATF pressure switch 3 AT-175,
AT-177
6. CAN communication line AT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Front brake (brake band)
AT-2909. Input clutchAT-313
No. Items Symptom Condition Diagnostic Item Reference
page

AT-86
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
61
Others Engine brake does
not work M3 → M2. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT- 2 3 5
4. Manual mode switchAT- 1 7 0
5. ATF pressure switch 6AT- 1 8 1
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Front brake (brake band)
AT- 2 9 09. Input clutchAT- 3 1 3
10. High and low reverse clutchAT- 3 2 3
62 Engine brake does
not work M2 → M1. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT- 2 3 5
4. Manual mode switchAT- 1 7 0
5. ATF pressure switch 5AT- 1 7 9
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Input clutch
AT- 3 1 39. High and low reverse clutchAT- 3 2 3
10. Direct clutchAT- 3 2 6
63 Maximum speed low. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. Direct clutch solenoid valveAT- 1 5 8
6. Control valve with TCMAT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assemblyAT- 3 0 8
9. Input clutchAT- 3 1 3
10. Gear systemAT- 2 7 8
11. High and low reverse clutchAT- 3 2 3
12. Direct clutchAT- 3 2 6
13. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-18, "
Cross-Sectional View (2WD Models)" or AT-19,
"Cross-Sectional View (AWD Models)" ) AT- 2 9 0
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT- 1 9 , "Cross-
Sectional View (AWD Models)" ) AT- 2 9 0
No. Items Symptom Condition Diagnostic Item
Reference
page

DTC P0745 LINE PRESSURE SOLENOID VALVE AT-129
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
DTC P0745 LINE PRESSURE SOLENOID VALVEPFP:31940
DescriptionACS002NB
The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in
response to a signal sent from the TCM.
CONSULT-II Reference ValueACS003KU
On Board Diagnosis LogicACS002NC

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0745 L/PRESS SOL/CIRC” with CONSULT-II or 4th judgement flicker without
CONSULT-II is detected under the following conditions.
–When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–When TCM detects as irregular by comparing target value with monitor value.
Possible CauseACS002ND

Harness or connectors
(Solenoid circuit is open or shorted.)

Line pressure solenoid valve
DTC Confirmation ProcedureACS002NE
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Touch “START”.
4. Engine start and wait at least 5 seconds.
5. If DTC is detected, go to “ AT- 1 3 0 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name Condition Display value (Approx.)
LINE PRES SOL During driving 0.2 - 0.6 A
BCIA0031E

TROUBLE DIAGNOSIS FOR SYMPTOMS AT-201
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
5. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
2. Check the following.
–Reverse brake. Refer to AT- 2 9 0 , "DISASSEMBLY" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
6. CHECK LINE PRESSURE
Check the line pressure with the engine idling. Refer to AT- 5 4 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 9.
NG - 1 >> Line pressure high: GO TO 7.
NG - 2 >> Line pressure low: GO TO 8.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
8. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
–Power train system. Refer to AT- 2 9 0 , "DISASSEMBLY" .
–Transmission case. Refer to AT- 2 9 0 , "DISASSEMBLY" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
SAT494G

AT-206
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
3. CHECK ACCELERATOR POSITION (APP) SENSOR
Check accelerator pedal position (APP) sensor. Refer to AT- 1 3 3 , "
DTC P1705 THROTTLE POSITION SEN-
SOR"
OK or NG
OK >> GO TO 4.
NG >> Repair or replace accelerator pedal position (APP) sensor.
4. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 5.
NG >> Refill ATF.
5. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT- 5 4 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
SAT638A
SAT494G

TROUBLE DIAGNOSIS FOR SYMPTOMS AT-211
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
4. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT- 5 4 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 7.
NG - 1 >> Line pressure high: GO TO 5.
NG - 2 >> Line pressure low: GO TO 6.
5. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
–Power train system. Refer to AT- 2 9 0 , "DISASSEMBLY" .
–Transmission case. Refer to AT- 2 9 0 , "DISASSEMBLY" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
7. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 2 , "
A/T Fluid Condition
Check" .
OK or NG
OK >> GO TO 8.
NG >> GO TO 11.
SAT494G
SCIA5199E

TROUBLE DIAGNOSIS FOR SYMPTOMS AT-213
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
3. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
4. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT- 5 4 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 7.
NG - 1 >> Line pressure high: GO TO 5.
NG - 2 >> Line pressure low: GO TO 6.
5. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
–Power train system. Refer to AT- 2 9 0 , "DISASSEMBLY" .
–Transmission case. Refer to AT- 2 9 0 , "DISASSEMBLY" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
SAT638A
SAT494G

ON-VEHICLE SERVICE AT-255
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Parking Components (2WD Models Only)ACS0081F
COMPONENTS
REMOVAL
1. Drain ATF through drain plug.
2. Remove exhaust front tube and center muffler with power tool. Refer to EX-3, "
Removal and Installation" .
3. Remove rear propeller shaft. Refer to PR-9, "
Removal and Installation" .
4. Remove control rod. Refer to AT- 2 3 4 , "
Control Rod Removal and Installation" .
5. Support transmission assembly with a transmission jack.
CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6. Remove rear engine mounting member with power tool. Refer to AT- 2 7 0 , "
Removal and Installation (2WD
Models)" .
1. Rear oil seal 2. Rear extension 3. Parking actuator support
4. Parking pawl 5. Return spring 6. Pawl shaft
7. Self-sealing bolt 8. Seal ring 9. Parking gear
10. Output shaft 11. Bearing race 12. Needle bearing
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-10, "
Components" .
However, refer to the following symbol for others.
: Apply Genuine Anaerobic Gasket or equivalent. Refer to GI-48, "
Recommended Chemical Products and Sealants" .
SCIA7433E