warning INFINITI FX35 2005 Owner's Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 657 of 4731
AV-58
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
DRIVE COMPUTER
Refer to Owner′s Manual for drive computer operating instructions.
TRIP Switch
When “TRIP” switch is pressed, display TRIP screen. As TRIP infor-
mation, it indicates journey time (TIME), trip odometer (DIST), aver-
age vehicle speed (AVG).
Pressing “TRIP” switch once cycles display from TRIP 1 →TRIP
2 → Display OFF →TRIP 1.
“TIME”
Journey time indication is performed by reset or battery connec-
tion.
When pushing “TRIP RESET” or “TRIP” switch more than
approximately 1.5 seconds, journey time will be reset.
If journey time is reset, journey distance and average speed will
be reset at the same time.
“DIST”
Trip odometer indication is performed by vehicle speed signal.
When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, driving distance will
be reset.
If trip odometer is reset, journey time and average speed will be reset at the same time.
“AVG”
Average speed indication is performed by running distance and running time.
Indication will be renewed every 30 seconds.
When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, average speed will
be reset.
After reset operation, the displays shows “ ” for 30 seconds.
FUEL ECON Switch
When “FUEL ECON” switch is pressed, display FUEL ECON screen.
As FUEL ECON information, it indicates average fuel consumption
(AVG), distance to empty (DTE).
Pressing “FUEL ECON” switch once cycles display from FUEL
ECON →Display OFF →FUEL ECON.
“AVG” (Average Fuel Consumption)
Average fuel consumption indication is performed by fuel con-
sumption signal and vehicle speed signal after system is reset.
Indication will be renewed every 30 seconds.
When pushing “TRIP RESET” or “FUEL ECON” switch more
than approximately 1.5 seconds, average fuel economy will be
reset.
After reset operation, the display shows “ . ” until the vehicle is driven 500 m (1,600 ft.) or 30 seconds
has passed.
“DTE” (Distance to Empty)
Distance to empty receives via CAN communication and indicates values calculated by meter.
Display range is max 999 miles (max 999 km).
If low-fuel WARNING is received from meter via CAN communication, distance to empty indication will be
“”.
Indication will be renewed every 30 seconds.
SKIA5916E
SKIA5917E
Page 660 of 4731
INTEGRATED DISPLAY SYSTEM AV-61
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
D/N SCREEN
Turning on “DAY/NIGHT” switch, DAY MODE or NIGHT MODE
is indicated for present mode.
If press “DAY/NIGHT” again when display adjustment lumi-
nance, change DAY-NIGHT (NIGHT-DAY) mode (screen of
adjustment luminance).
As follows:
Press “PREV” or not operate for 10sec. when displayed screen
of adjustment luminance, back to default screen (same mode).
Can adjust luminance by “DISP” switch. Light can be adjusted by pressing “+” (bright) or “–” (dark).
Adjustment range is a 12 stage (MIN to MAX) and default set value is 10 (DAY) and 4 (NIGHT).
WARNING INDICATIONS
When BCM receives warning signal from some control units or sensors, then combination meter warning lamp
is illuminated.
Then BCM sends warning signal to display unit warning indications on the screen.
AV COMMUNICATION LINE
Display unit is controlled by the following unit with AV communication line.
A/C and AV switch
CAN Communication System DescriptionAKS007Z5
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007YZ
Refer to LAN-30, "CAN Communication Unit" .
Component Parts and Harness Connector Location AKS005U2
NOW Change display
DAY DAY →NIGHT →DAY →·····
NIGHT NIGHT →DAY →NIGHT →·····
SKIA5920E
Warning indicators Warning lamps in
instrument panel Warning detection and cancel conditions Cases of malfunction
DOOR OPEN Door Detection
condition Vehicle is running [approx. 3.5 km/h (2 MPH) or
faster] and door ajar of any of the doors is detected. Door is open.
Cancel
condition Vehicle is stopped and all the doors close.
SKIA4970E
Page 675 of 4731
AV-76
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Display Detail Screen
NOTE:
Except an audio screen.
HVAC DETAIL SCREEN
Press the joystick, start auto air conditioner system self-diagnosis.
Refer to AT C - 5 3 , "
Self-diagnosis Function" .
VERSION CHECK
Check ID and version of display, A/C and AV switch, audio, IVCS, changer, and Satellite Radio.
CAN DIAG MNTR (CAN DIAG MONITOR)
Display CAN communication status.
Items Description
FULL BLINK All display unit segments turn ON.
BLANK–ADJ Adjust the display time-out for 5 to 15 seconds. (Default is
10 seconds.)
NOTE
WARNING Select warning indication ON/OFF. (Default is ON.)
SKIA5925E
SKIA5926E
Items shown Contents
CANCOMM OK/NG CAN1 OK/UNKWN
CAN2 OK/UNKWN
CAN3 OK/UNKWN
CAN4 OK/UNKWN
CAN5 OK/UNKWN
CAN6 OK/UNKWN
CAN7 OK/UNKWN
CAN8 OK/UNKWN
CAN9 OK/UNKWN
SKIA5927E
Page 677 of 4731
AV-78
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Trouble Diagnosis Chart by SymptomAKS005UB
Symptom Suspect Systems and reference
No screen is shown. Refer to
AV-79, "
Power Supply and Ground Circuit Check for Display Unit" .
If above is normal, replace display unit.
Screen does not switch to nighttime mode after the
lighting switch is turned 1st. Refer to
AV-81, "
Illumination Signal Inspection" .
TRIP and FUEL ECON screen do not appear. Refer to AV-82, "
Ignition Signal Inspection" .
Journey distance (DIST) is not added up. Refer to AV-80, "
Vehicle Speed Signal Inspection" .
Average vehicle speed (AVG) is not displayed.
Average fuel consumption (AVG) is not displayed.
Refer to AV-80, "Vehicle Speed Signal Inspection" .
Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Distance to empty (DTE) is not displayed.
Check if speedometer operates. If it does not operate, go to AV- 8 0 , "Vehicle
Speed Signal Inspection" .
Check if fuel gauge operates. If it does not operate, go to DI-22, "Fuel Level
Sensor Signal Inspection" .
Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Tire pressure is not displayed.
Check BCM (Body Control Module). Refer to BCS-3, "BCM (BODY CONTROL
MODULE)" .
Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Door warning screen does not appear.
Refer to AV-80, "Vehicle Speed Signal Inspection" .
Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
A/C and AV switch and all switch operation are not
possible.
(Do not start self-diagnosis.)
Refer to AV-80, "Power Supply and Ground Circuit Check for A/C and AV
Switch" .
Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .
Refer to AV-84, "AV Communication Line Inspection" .
If above is normal, replace display unit.
Audio operation is not possible.
Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .
Refer to AV-82, "Audio Communication Line Inspection" .
Audio steering wheel switches do not function. Refer to
AV-86, "
Audio Steering Wheel Switch Inspection" .
If above is normal, replace AV and A/C switch.
Air conditioner operation is not possible.
Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .
Refer to AV-85, "CAN Communication Line Inspection" .
Page 700 of 4731
NAVIGATION SYSTEM AV-101
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
“TRACKING” MODE
To delete the tracking marks on the map, select “Off”.
To leave the tracking marks on the map, select “On”.
NOTE:
When a trail display is turned OFF, trail data is erased from the mem-
ory.
GUIDANCE VOLUME
Description
Following guidance volume setting can be changed.
Activation/Deactivation Setting
The voice prompt can be turned on/off by pressing the “Guidance Volume” button.
Voice Volume Setting
Volume of the voice can be controlled by bending the joystick to left/right.
DISPLAY WITH PUSHED “TRIP” BUTTON
When the “TRIP” button is pushed, the following models will display on the screen.
Warning message (if there are any) →TRIP1 →TRIP2 →FUEL ECONOMY →MAINTENANCE →OFF.
SKIA0559E
SKIA4497E
Display items Display/Setting contents Reference
page
Trip 1 o r Trip2 Elapsed Time Displays driving time with a range of 0000:00:00 to 9999:59:59.
AV-102,
"TRIP 1 OR
TRIP 2"
Driving Distance
[(km) or (miles)] Displays driving distance with a range of 00000.0 to 99999.9.
Average speed
[(km/h) or (MPH)] Displays average speed with a range of 000.0 to 999.9.
Fuel Economy Average Fuel Economy
[(MPG) or (l/100km)] Displays fuel economy with ignition switch ON, average fuel econ-
omy each 30 minutes. AV-102,
"FUEL
ECONOMY"
Distance to Empty [(km) or
(miles)], [(MPG) or (l/100km)] Displays possible driving distance with remaining fuel.
Fuel Economy (MPG) Displays fuel economy each approx. 100 ms.
Maintenance Engine oil Maintenance intervals of engine oil and setting of oil change cycle.
AV-102,
"MAINTE-
NANCE"
Tire rotation Maintenance intervals of tire and setting of tire replacement cycle.
Tire pressure Tire pressure displayed as tire pressure information.
Page 702 of 4731
NAVIGATION SYSTEM AV-103
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
TIRE PRESSURE
Pressure indication in psi on the screen indicates that the
pressure is being measured. After a few driving trips, the pres-
sures for all four tires will be displayed.
The order of tire pressure figures displayed on the screen does
not correspond with the actual order of the tire position.
Tire pressure rises and falls depending on the heat caused by
the vehicle's traveling condition and the temperature.
FLAT TIRE–very low tire air pressure.
NOTE:
In a case of FLAT TIRE pressure, interrupt screen is not shown
on the display.
On the screen of TIRE PRESSURE, “FLAT TIRE”, “Check”, “All tire” is displayed.
WARNING INDICATIONS
Warning signal (door switch signal) is received from BCM through
CAN communication line.
SKIA5994E
SKIA5995E
Warning
indicators Warning lamps in
instrument panel Warning detection and cancel conditions
Cases of
malfunction
DOOR OPEN Door Detection condition
Vehicle is running [approx. 5km/h (3 MPH) or faster]
and door ajar of any of the doors is detected. Door is open.
Cancel condition Vehicle is stopped and all the doors lock.
Page 767 of 4731
AV-168
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
WARNING DOOR OPEN Screen Is Not ShownAKS007K6
1. CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal. Refer to AV- 1 4 6 , "
Vehicle Speed Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 5 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 3.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-5, "
Precautions When
Using CONSULT-II" .
3. CHECK COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 2 , "
Display Communication Line Check (Between Display
Control Unit and Display)" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
Tire Pressure Is Not Displayed AKS007K7
1. CHECK BCM (BODY CONTROL MODULE)
Check BCM (Body Control Module). Refer to BCS-3, "
BCM (BODY CONTROL MODULE)" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 5 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 3.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-5, "
Precautions When
Using CONSULT-II" .
3. CHECK COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 2 , "
Display Communication Line Check (Between Display
Control Unit and Display)" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
Unable to Operate All of A/C and AV Switch (Unable to Start Self-Diagnosis)AKS007K8
1. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to AV- 1 4 5 , "
Power Supply and Ground Circuit Check for A/C
and AV Switch" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
Page 801 of 4731
BCS-2
PRECAUTIONS
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS007KR
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Page 807 of 4731
BCS-8
BCM (BODY CONTROL MODULE)
Revision: 2005 July 2005 FX
SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
System Reference
Power door lock BL-21, "
POWER DOOR LOCK SYSTEM"
Remote keyless entryBL-56, "REMOTE KEYLESS ENTRY SYSTEM"
Power window NOTEGW-15, "POWER WINDOW SYSTEM"
Sunroof NOTERF-10, "SUNROOF"
Room lamp timerLT-159, "INTERIOR ROOM LAMP"
Warning chimeDI-58, "WARNING CHIME"
Rear wiperWW-38, "REAR WIPER AND WASHER SYSTEM"
Low tire pressure warning systemWT-7, "LOW TIRE PRESSURE WARNING SYSTEM"
System Reference
Panic alarm BL-56, "
REMOTE KEYLESS ENTRY SYSTEM"
Theft warningBL-186, "VEHICLE SECURITY (THEFT WARNING) SYSTEM"
IVIS (NATS)BL-213, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)"
HeadlampLT- 7 , "HEADLAMP - XENON TYPE -"
LT- 3 9 , "DAYTIME LIGHT SYSTEM"
Auto light systemLT- 5 5 , "AUTO LIGHT SYSTEM"
Parking, license plate and tail lamps
Battery saver control LT-129, "PARKING, LICENSE PLATE AND TAIL LAMPS"
Front fog lamp
LT- 7 9 , "FRONT FOG LAMP"
Front wiperWW-4, "FRONT WIPER AND WASHER SYSTEM"
Rear window defoggerGW-86, "REAR WINDOW DEFOGGER"
System Reference
Warning chime DI-58, "
WARNING CHIME"
Turn signal and hazard warning lampsLT- 9 1 , "TURN SIGNAL AND HAZARD WARNING LAMPS"
Daytime running lightLT- 3 9 , "DAYTIME LIGHT SYSTEM"
System Reference
Intelligent Key BL-89, "
INTELLIGENT KEY SYSTEM"
Page 808 of 4731
BCM (BODY CONTROL MODULE) BCS-9
C
D E
F
G H
I
J
L
M A
B
BCS
Revision: 2005 July 2005 FX
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote control entry system key fob
All-door locking actuator
Turn signal lamp (LH, RH)
Intelligent key system Intelligent key unit
All-door locking actuator
Fuel lid Lock actuator
Turn signal lamp (LH, RH)
Combination meter
Power door lock system
Power window main switch
(door lock and unlock switch)
Power window sub switch (passenger side)
(door lock and unlock switch) All-door locking actuator
Power supply (IGN) to power window, sunroof Ignition power supply Power window and sunroof system
Power supply (BAT) to power window, sunroof
and power seat Battery power supply
Power window, sunroof system and
power seat
Panic alarm
Key switch
Key fob IPDM E/R
Theft warning system
All-door switch
Hood switch
Key fob
Power window main switch (door lock and
unlock switch)
IPDM E/R
Security indicator lamp
Auto light system
Optical sensor
Combination switch IPDM E/R
Battery saver control
Ignition switch
Combination switch IPDM E/R
Headlamp Combination switch IPDM E/R
Daytime system
Combination meter
ECM Clearance lamp
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch
Turn signal lamp
Combination meter
Hazard lamp Hazard switch
Turn signal lamp
Combination meter
Room lamp timer
Key switch
key fob
Power window main switch (door lock and
unlock switch)
Front door switch driver side
All-door switch Interior room lamp
Key warning chime
Key switch
Front door switch driver side Combination meter
(warning buzzer)
Light warning chime
Combination switch
Front door switch driver side Combination meter
(warning buzzer)
Seat belt warning chime
Combination meter (Seat belt buckle
(driver side) switch)
Ignition switch Combination meter
(warning buzzer)