service indicator INFINITI FX35 2005 Workshop Manual

AUTOMATIC DRIVE POSITIONER SE-43
C
D E
F
G H
J
K L
M A
B
SE
Revision: 2005 July 2005 FX
Sliding Motor Circuit CheckAIS002XN
1. CHECK SEAT SLIDING MECHANISM
Check the following.

Operation malfunction caused by sliding rail deformation or pinched harness or other foreign materials

Operation malfunction caused by foreign materials adhered to the sliding motor or sliding rail connector
rod

Operation malfunction and interference with other parts by poor installation
OK or NG
OK >> GO TO 2.
NG >> Repair the malfunctioning part and check again.
A part of seat system does not operate (only manual
operation). 1. Sliding switch circuit check
SE-68
2. Reclining switch circuit checkSE-69
3. Front lifting switch circuit checkSE-71
4. Rear lifting switch circuit checkSE-72
5. If the above systems are normal, replace the driver
seat control unit. SE-15
A part of steering tilt, telescopic and door mirror does not
operate (only manual operation). 1. Door mirror remote control (change over switch) circuit
check SE-78
2. Door mirror remote control (mirror switch) switching cir-
cuit check SE-80
3. Tilt switch check
SE-76
4. Telescopic switch checkSE-74
5. If the above systems are normal, replace the automatic
drive positioner control unit. SE-15
Only memory switch operation dose not operate. 1. Seat memory switch circuit check
SE-862. If the above systems are normal, replace the driver
seat control unit. SE-15
Seat memory indicator lamps 1 and 2 do not illuminate. 1. Seat memory indicator lamp circuit check
SE-882. If all the above systems are normal, replace the driver
seat control unit. SE-15
The Entry/Exiting does not operated when door is opened
and closed.
(The Entry/Exiting operates with key switch) 1. Front door switch (driver side) circuit check
SE-66
2. If all the above systems are normal, replace the BCMBCS-16
Only door mirror system dose not operated (only auto-
matic operation). Steering and door mirror sensor power supply and ground
circuit check SE-65
Only seat sliding and seat reclining operation does not
operation Sliding switch and reclining switch ground circuit check
SE-73
Only sear lifting (front and rear) operation does not opera-
tion Front lifting switch and rear lifting switch ground circuit
check SE-74
Only lumber support does not operate Lumber support circuit check
SE-90
Symptom Diagnoses / service procedure Reference
page

WT-4
ROAD WHEEL
Revision: 2005 July 2005 FX
ROAD WHEELPFP:40300
InspectionAES000OP
ALUMINUM WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel runout.
a. Remove tire from aluminum wheel and mount on a tire balance machine.
b. Set dial indicator as shown in the figure.
STEEL WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel runout.
a. Remove tire from steel wheel and mount wheel on a tire balance machine.
b. Set two dial indicators as shown in the figure.
c. Set each dial indicator to 0.
d. Rotate wheel and check dial indicators at several points around the circumference of the wheel.
e. Calculate runout at each point as shown below.
f. Select maximum positive runout value and the maximum nega- tive value.
Add the two values to determine total runout.
In case a positive or negative value is not available, use the
maximum value (negative or positive) for total runout.
If the total runout value exceeds the limit, replace steel wheel. Wheel runout (Dial indicator value):
Refer to WT-37, "
SERVICE DATA"
SFA975B
Radial runout = (A + B)/2
Lateral runout = (C + D)/2
Wheel runout : Refer to WT-37, "
SERVICE DATA"SFA981B