audio INFINITI FX35 2005 Workshop Manual

AUDIO ANTENNA AV-51
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
AUDIO ANTENNAPFP:28200
System DescriptionAKS007WE
With the ignition switch in ACC or ON, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to audio unit terminal 10.
Ground is supplied through the case of the antenna amp.
When the radio switch is turned ON, antenna signal is supplied

through audio unit terminal 5

to the antenna amp.
Then the antenna amp. is activated.
The amplified radio signals are supplied to the audio unit through the antenna amp.

AV-52
AUDIO ANTENNA
Revision: 2005 July 2005 FX
Wiring Diagram — M/ANT —AKS007WF
TKWM0569E

AUDIO ANTENNA AV-53
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Terminals and Reference Value for Audio UnitAKS007WW
Antenna Amp. InspectionAKS007WX
1. CHECK ANTENNA FEEDER
Check with visual observation if antenna feeder between audio unit and antenna amp. has disconnection or
malfunction on the mounting part (engagement, looseness of shield earth, etc.).
OK or NG
OK >> GO TO 2
NG >> Replace antenna feeder.
2. CHECK ANTENNA SIGNAL
1. Turn the ignition switch ACC.
2. Check voltage between audio unit harness connector M58 ter- minal 5 (R/W) and ground.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace audio unit.
Terminal
(Wire color) Item Signal
input/
output Condition
Reference value Example of
symptom
+– Ignition
switch Operation
5 (R/W) Ground Antenna signal Input ACC — Approx. 12 V Receiving status of radio
broadcast becomes bad.
10 (LG/R) Ground ACC power
supply Input ACC — Battery voltage
System does not work
properly.
5 (R/W) – Ground : Approx. 12 V
SKIA6854E

AV-54
AUDIO ANTENNA
Revision: 2005 July 2005 FX
Location of AntennaAKS005TX
Window Antenna RepairAKS005TY
CHECK ELEMENT
1. Attach probe circuit tester (ohm setting) to antenna terminal on
each side.
PKIB5079E
SEL250I

AUDIO ANTENNA AV-55
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX

When measuring continuity, wrap tin foil around the top
of probe. Then, press the foil against the wire with your
finger.
2. If an element is broken, no continuity will exist.
3. To locate a break, move probe along element. Tester needle will swing abruptly when probe passes the broken point.
SEL122R
SEL252I
SEL253I

AV-56
AUDIO ANTENNA
Revision: 2005 July 2005 FX
Removal and Installation of Roof AntennaAKS005TZ
REMOVAL
1. Remove head lining. Refer to EI-41, "HEADLINING" .
2. Remove nut and remove rod and antenna base.
3. Remove instrument panel. Refer to IP-10, "
INSTRUMENT
PANEL ASSEMBLY" .
4. Disassembly antenna feeder (upper) and antenna feeder (lower).
5. Disengaged the clips (7) to separate antenna feeder (upper) from vehicle.
6. Pull off antenna feeder (lower) from audio unit.
7. Disengaged the clips (5) to separate antenna feeder (lower) from vehicle.
INSTALLATION
Installation is the reverse order of removal.
PKIA2463E
SKIA5821E

INTEGRATED DISPLAY SYSTEM AV-57
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
INTEGRATED DISPLAY SYSTEMPFP:28090
System DescriptionAKS005U0
A/C AND AV SWITCH SYSTEM
Refer to Owner′s Manual for A/C and AV switch operating instructions.
Using the A/C and AV switch at the center of the instrument panel, the controls of the following systems are
centralized:

Integrated display system (Drive computer, setting screen, etc.)

Auto A/C system

Audio system
PRECAUTION OF LCD MONITOR

In order to use LED for backlight of a display, by interior temperature, brightness may change. In low tem-
perature, the refreshing rate of the picture also becomes low because of the low response of the LCD
monitor. When the interior becomes warm, however, the LCD recovers the normal display.

Backlight sometimes flickers or darkens according to the wearing out of LCD and the number of times
switched ON and OFF. In this case, display unit should be replaced. (Exchange only of backlight is impos-
sible.)
POWER SUPPLY AND GROUND
Power is supplied at all times

through 15A fuse (No. 32, located in fuse and fusible link box)

to audio unit terminal 6

to display unit terminal 1 and

to A/C and AV switch terminal 1.
When ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 35

to audio unit terminal 10

to display unit terminal 2 and

to A/C and AV switch terminal 2.
When ignition switch is in ON or START position, power is supplied

through 10A fuse [No. 12, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 22 and

to display unit terminal 3.
Ground is supplied

to unified meter and A/C amp. terminals 29, 30

to display unit terminals 6 and 15 and

to A/C and AV switch terminal 5

through body grounds M35, M45 and M85.
Ground is supplied through the case of the audio unit.

AV-72
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Terminals and Reference Value for Display UnitAKS005U6
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
1 (W/L) Ground Battery power
supply Input OFF — Battery voltage System does not
work properly.
2 (LG/R) Ground ACC power
supply Input ACC — Battery voltage System does not
work properly.
3 (G/R) Ground Ignition signal Input ON — Battery voltage A/C operation is
not possible.
Vehicle informa-
tion setting is not possible.
4 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (1st position). Approx. 12 V Audio unit illumi-
nation does not
come on when
lighting switch is
ON (1st position).
Turn lighting
switch OFF. Approx. 0 V
6 (B) Ground Ground — ON — Approx. 0 V —
7 (R/G) Ground Vehicle speed
signal (8-pulse) Input ON When vehicle
speed is approx.
40 km/h (25 MPH) Drive computer
item is not dis-
played correctly.
8 (LG) Ground Audio TX
(DSP-AUD) Output ON
Operate audio
volume. Audio does not
operate properly.
9 — Shield ground — — — — —
10 (B/Y) Ground Audio RX
(AUD-DSP) Input ON
Operate audio
volume. Audio does not
operate properly.
11 (B/R) Ground Communica-
tion signal (+) Input/
output ON — System does not
work properly.
12 — Shield ground — — — — —
PKIA1935E
SKIA4402E
SKIA4403E
SKIA0175E

INTEGRATED DISPLAY SYSTEM AV-73
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Terminals and Reference Value for A/C and AV SwitchAKS005U7
13 (W/R) Ground Communica-
tion signal (-) Input/
output ON — System does not
work properly.
14 (L) — CAN-H — — — — —
15 (B) — Shield ground — — — — —
16 (R) — CAN-L — — — — — Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltag e Example of
symptom
+– Ignition
switch Operation
SKIA0176E
Terminal No.
(Wire color) Item Signal
input/
output Condition
Vo l ta g e Example of
symptom
+– Ignition
switch Operation
1 (W/L) Ground Battery power
supply Input OFF — Battery voltage System does not
work properly.
2 (LG/R) Ground ACC power
supply Input ACC — Battery voltage System does not
work properly.
5 (B) Ground Ground — ON — Approx. 0 V —
6 (B/R) Ground Communica-
tion signal (+) Input/
output ON —
System does not
work properly.
7 — Shield ground — — — — —
8 (W/R) Ground Communica-
tion signal (-) Input/
output ON —
System does not
work properly.
12 (R/G) Ground Steering SW
A Input ON Press MODE
switch. Approx. 0 V
Audio steering
wheel switches
do not function.
Press SEEK UP
switch. Approx. 1.7 V
Press VOL UP
switch. Approx. 3.3 V
Except for above Approx. 5 V
SKIA0175E
SKIA0176E

AV-74
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
On Board Self-Diagnosis FunctionAKS005U8
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.
DIAGNOSIS ITEM
Self-Diagnosis ModeAKS005U9
OPERATION PROCEDURES
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” switch, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
4. Display unit connection check screen.
5. Select each connecting unit (CHANGER, SATELLITE RADIO).
13 (G/W) Ground Steering SW
B Input ON Press POWER
switch. Approx. 0 V
Audio steering
wheel switches
do not function.
Press SEEK
DOWN switch. Approx. 1.7 V
Press VOL DOWN
switch. Approx. 3.3 V
Except for above Approx. 5 V
14 (B/Y) — Steering SW
ground —— — — Audio steering
wheel switches
do not function.
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
Mode Item Description Reference page
Self-diagnosis NETWORK CHECK
Check network between control unit and switch connected
from display unit via communication line. AV-75, "
NETWORK CHECK"
PARTS CHECK
Perform diagnosis and setting of display unit.

Perform self-diagnosis for auto air conditioner system. AV- 7 5 , "PARTS CHECK"
VERSION CHECK Displays version of each unit.
AV- 7 6 , "VERSION CHECK"
CAN DIAG MNTR Display unit displays CAN communication status. AV- 7 6 , "CAN DIAG MNTR
(CAN DIAG MONITOR)"
PKIB4131E
SKIA5921E