p1705 INFINITI FX35 2005 Service Manual

AT-2Revision: 2005 July 2005 FX
Possible Cause ....................................................
.114
DTC Confirmation Procedure .............................. .114
Wiring Diagram — AT — PNP/SW ...................... .115
Diagnostic Procedure .......................................... .116
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) .............................................. .118
Description ........................................................... .118
CONSULT-II Reference Value ............................. .118
On Board Diagnosis Logic ................................... .118
Possible Cause .................................................... .118
DTC Confirmation Procedure .............................. .118
Wiring Diagram — AT — VSSA/T ........................ .120
Diagnostic Procedure .......................................... .121
DTC P0725 ENGINE SPEED SIGNAL .................. .123
Description ........................................................... .123
CONSULT-II Reference Value ............................. .123
On Board Diagnosis Logic ................................... .123
Possible Cause .................................................... .123
DTC Confirmation Procedure .............................. .123
Diagnostic Procedure .......................................... .124
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE ................................................ .125
Description ........................................................... .125
CONSULT-II Reference Value ............................. .125
On Board Diagnosis Logic ................................... .125
Possible Cause .................................................... .125
DTC Confirmation Procedure .............................. .125
Diagnostic Procedure .......................................... .126
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .127
Description ........................................................... .127
CONSULT-II Reference Value ............................. .127
On Board Diagnosis Logic ................................... .127
Possible Cause .................................................... .127
DTC Confirmation Procedure .............................. .127
Diagnostic Procedure .......................................... .128
DTC P0745 LINE PRESSURE SOLENOID VALVE .129
Description ........................................................... .129
CONSULT-II Reference Value ............................. .129
On Board Diagnosis Logic ................................... .129
Possible Cause .................................................... .129
DTC Confirmation Procedure .............................. .129
Diagnostic Procedure .......................................... .130
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ..................................................................... .131
Description ........................................................... .131
On Board Diagnosis Logic ................................... .131
Possible Cause .................................................... .131
DTC Confirmation Procedure .............................. .131
Diagnostic Procedure .......................................... .131
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ..................................................................... .132
Description ........................................................... .132
On Board Diagnosis Logic ................................... .132
Possible Cause .................................................... .132
DTC Confirmation Procedure .............................. .132
Diagnostic Procedure .......................................... .132
DTC P1705 THROTTLE POSITION SENSOR ...... .133
Description ........................................................... .133
CONSULT-II Reference Value ............................. .133 On Board Diagnosis Logic ...................................
.133
Possible Cause .................................................... .133
DTC Confirmation Procedure ............................... .133
Diagnostic Procedure ........................................... .134
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ................................................................. .136
Description ........................................................... .136
CONSULT-II Reference Value .............................. .136
On Board Diagnosis Logic ................................... .136
Possible Cause .................................................... .136
DTC Confirmation Procedure ............................... .136
Wiring Diagram — AT — FTS .............................. .137
Diagnostic Procedure ........................................... .138
Component Inspection ......................................... .140
DTC P1716 TURBINE REVOLUTION SENSOR ... .141
Description ........................................................... .141
CONSULT-II Reference Value .............................. .141
On Board Diagnosis Logic ................................... .141
Possible Cause .................................................... .141
DTC Confirmation Procedure ............................... .141
Diagnostic Procedure ........................................... .142
DTC P1721 VEHICLE SPEED SENSOR MTR ...... .143
Description ........................................................... .143
CONSULT-II Reference Value .............................. .143
On Board Diagnosis Logic ................................... .143
Possible Cause .................................................... .143
DTC Confirmation Procedure ............................... .143
Diagnostic Procedure ........................................... .144
DTC P1730 A/T INTERLOCK ................................ .145
Description ........................................................... .145
On Board Diagnosis Logic ................................... .145
Possible Cause .................................................... .145
DTC Confirmation Procedure ............................... .145
Judgement of A/T Interlock .................................. .145
Diagnostic Procedure ........................................... .146
DTC P1731 A/T 1ST ENGINE BRAKING .............. .148
Description ........................................................... .148
CONSULT-II Reference Value .............................. .148
On Board Diagnosis Logic ................................... .148
Possible Cause .................................................... .148
DTC Confirmation Procedure ............................... .148
Diagnostic Procedure ........................................... .149
DTC P1752 INPUT CLUTCH SOLENOID VALVE . .150
Description ........................................................... .150
CONSULT-II Reference Value .............................. .150
On Board Diagnosis Logic ................................... .150
Possible Cause .................................................... .150
DTC Confirmation Procedure ............................... .150
Diagnostic Procedure ........................................... .151
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ............................................................. .152
Description ........................................................... .152
CONSULT-II Reference Value .............................. .152
On Board Diagnosis Logic ................................... .152
Possible Cause .................................................... .152
DTC Confirmation Procedure ............................... .152
Diagnostic Procedure ........................................... .153
DTC P1757 FRONT BRAKE SOLENOID VALVE .. .154
Description ........................................................... .154

INDEX FOR DTC AT-5
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
INDEX FOR DTCPFP:00024
Alphabetical Index ACS002L1
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 1 0 6
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL. Items
(CONSULT-II screen terms) DTC
Reference page
OBD-II Except OBD-II
CONSULT-II GST (*1) CONSULT-II only “A/T”
A/T 1ST E/BRAKING — P1731 AT- 1 4 8
ATF PRES SW 1/CIRC — P1841AT- 1 7 5
ATF PRES SW 3/CIRC — P1843AT- 1 7 7
ATF PRES SW 5/CIRC — P1845AT- 1 7 9
ATF PRES SW 6/CIRC — P1846AT- 1 8 1
A/T INTERLOCK P1730 P1730AT- 1 4 5
A/T TCC S/V FNCTN P0744 P0744 AT- 1 2 7
ATF TEMP SEN/CIRC P0710 P1710AT- 1 3 6
CAN COMM CIRCUIT U1000 U1000AT- 1 0 6
D/C SOLENOID/CIRC P1762 P1762AT- 1 5 8
D/C SOLENOID FNCTN P1764 (*3) P1764 AT- 1 6 0
ENGINE SPEED SIG P0725 (*2) P0725AT- 1 2 3
FR/B SOLENOID/CIRC P1757 P1757AT- 1 5 4
FR/B SOLENOID FNCT P1759 P1759 AT- 1 5 6
HLR/C SOL/CIRC P1767 P1767AT- 1 6 2
HLR/C SOL FNCTN P1769 (*3) P1769 AT- 1 6 4
I/C SOLENOID/CIRC P1752 P1752AT- 1 5 0
I/C SOLENOID FNCTN P1754 (*3) P1754 AT- 1 5 2
L/PRESS SOL/CIRC P0745 P0745AT- 1 2 9
LC/B SOLENOID/CIRC P1772 P1772AT- 1 6 6
LC/B SOLENOID FNCT P1774 P1774 AT- 1 6 8
MANU MODE SW/CIRC — P1815AT- 1 7 0
PNP SW/CIRC P0705 P0705 AT- 11 4
STARTER RELAY/CIRC — P0615AT- 1 0 9
TCC SOLENOID/CIRC P0740 P0740AT- 1 2 5
TCM P0700(*2) P0700 AT- 11 3
TCM·RAM — P1702AT- 1 3 1
TCM·ROM — P1703AT- 1 3 2
TP SEN/CIRC A/T P1705(*2) P1705AT- 1 3 3
TURBINE REV S/CIRC P1716 P1716AT- 1 4 1
VEH SPD SE/CIR·MTR — P1721AT- 1 4 3
VEH SPD SEN/CIR AT P0720 P0720 AT- 11 8

AT-6
INDEX FOR DTC
Revision: 2005 July 2005 FX
DTC No. Index ACS002L2
NOTE:
If DTC U1000 is displayed with other DTCs, first perform the trouble diagnosis for DTC U1000. Refer to
AT- 1 0 6
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL. DTC
Items
(CONSULT-II screen terms) Reference page
OBD-II Except OBD-II
CONSULT-II GST (*1) CONSULT-II
only “A/T”
— P0615 STARTER RELAY/CIRC AT- 1 0 9
P0700(*2) P0700 TCM AT- 11 3
P0705 P0705 PNP SW/CIRCAT- 11 4
P0710 P1710 ATF TEMP SEN/CIRCAT- 1 3 6
P0720 P0720 VEH SPD SEN/CIR AT AT- 11 8
P0725 (*2) P0725 ENGINE SPEED SIG AT- 1 2 3
P0740 P0740 TCC SOLENOID/CIRCAT- 1 2 5
P0744 P0744 A/T TCC S/V FNCTNAT- 1 2 7
P0745 P0745 L/PRESS SOL/CIRCAT- 1 2 9
— P1702 TCM·RAMAT- 1 3 1
— P1703 TCM·ROMAT- 1 3 2
P1705 (*2) P1705 TP SEN/CIRC A/T AT- 1 3 3
P1716 P1716 TURBINE REV S/CIRCAT- 1 4 1
— P1721 VEH SPD SE/CIR·MTRAT- 1 4 3
P1730 P1730 A/T INTERLOCK AT- 1 4 5
— P1731 A/T 1ST E/BRAKINGAT- 1 4 8
P1752 P1752 I/C SOLENOID/CIRC AT- 1 5 0
P1754 (*3) P1754 I/C SOLENOID FNCTN AT- 1 5 2
P1757 P1757 FR/B SOLENOID/CIRCAT- 1 5 4
P1759 (*3) P1759 FR/B SOLENOID FNCT AT- 1 5 6
P1762 P1762 D/C SOLENOID/CIRCAT- 1 5 8
P1764 (*3) P1764 D/C SOLENOID FNCTN AT- 1 6 0
P1767 P1767 HLR/C SOL/CIRCAT- 1 6 2
P1769 P1769 HLR/C SOL FNCTNAT- 1 6 4
P1772 P1772 LC/B SOLENOID/CIRCAT- 1 6 6
P1774 P1774 LC/B SOLENOID FNCTAT- 1 6 8
— P1815 MANU MODE SW/CIRCAT- 1 7 0
— P1841 ATF PRES SW 1/CIRCAT- 1 7 5
— P1843 ATF PRES SW 3/CIRCAT- 1 7 7
— P1845 ATF PRES SW 5/CIRCAT- 1 7 9
— P1846 ATF PRES SW 6/CIRCAT- 1 8 1
U1000 U1000 CAN COMM CIRCUIT AT- 1 0 6

AT-48
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
4 ❏
Perform all road tests and enter checks in required inspection items. AT- 5 6
4-1. Check before engine is started
AT- 5 6
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 9 3 .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 3
,AT- 1 0 3
❏ AT-106, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-109, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT- 11 3 , "
DTC P0700 TCM"
❏ AT- 11 4 , "DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT- 11 8 , "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-123, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-125, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-127, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-129, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-131, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-132, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-133, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-136, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-141, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-143, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-145, "
DTC P1730 A/T INTERLOCK" .
❏ AT-148, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-150, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-152, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-154, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-156, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-158, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-160, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-162, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-164, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-166, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-168, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-170, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-175, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-177, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-179, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-181, "
DTC P1846 ATF PRESSURE SWITCH 6" .
4-2. Check at Idle
AT- 5 7
❏ AT-194, "Engine Cannot Be Started in “P” or “N” Position" .
❏ AT-195, "
In “P” Position, Vehicle Moves When Pushed"
❏ AT-196, "In “N” Position, Vehicle Moves" .
❏ AT-197, "
Large Shock (“N” to “D” Position)" .
❏ AT-200, "
Vehicle Does Not Creep Backward in “R” Position" .
❏ AT-203, "
Vehicle Does Not Creep Forward in “D” Position" .
4-3. Cruise Test
AT- 5 8
Part 1
❏ AT-205, "
Vehicle Cannot Be Started from D1" .
❏ AT-208, "
A/T Does Not Shift: D1 → D2" .
❏ AT-210, "
A/T Does Not Shift: D2 → D3" .
❏ AT-212, "
A/T Does Not Shift: D3 → D4" .
❏ AT-215, "
A/T Does Not Shift: D4 → D5" .
❏ AT-217, "
A/T Does Not Perform Lock-up"
❏ AT-219, "A/T Does Not Hold Lock-up Condition" .
❏ AT-221, "
Lock-up Is Not Released" .
❏ AT-221, "
Engine Speed Does Not Return to Idle" .

TROUBLE DIAGNOSIS AT-49
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
44-3 Part 2
AT- 6 0
❏ AT- 2 0 5 , "Vehicle Cannot Be Started from D1" .
❏ AT- 2 0 8 , "
A/T Does Not Shift: D1 → D2" .
❏ AT- 2 1 0 , "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 1 2 , "
A/T Does Not Shift: D3 → D4" .
Part 3 AT- 6 1
❏ AT- 2 2 3 , "Cannot Be Changed to Manual Mode" .
❏ AT- 2 2 3 , "
A/T Does Not Shift: 5th Gear → 4th Gear" .
❏ AT- 2 2 5 , "
A/T Does Not Shift: 4th Gear → 3rd Gear" .
❏ AT- 2 2 7 , "
A/T Does Not Shift: 3rd Gear → 2nd Gear" .
❏ AT- 2 2 9 , "
A/T Does Not Shift: 2nd Gear → 1st Gear" .
❏ AT- 2 3 1 , "
Vehicle Does Not Decelerate by Engine Brake" .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 3
,AT- 1 0 3
❏ AT-106, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-109, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT-113, "
DTC P0700 TCM"
❏ AT-114, "DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT-118, "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-123, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-125, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-127, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-129, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-131, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-132, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-133, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-136, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-141, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-143, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-145, "
DTC P1730 A/T INTERLOCK" .
❏ AT-148, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-150, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-152, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-154, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-156, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-158, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-160, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-162, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-164, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-166, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-168, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-170, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-175, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-177, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-179, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-181, "
DTC P1846 ATF PRESSURE SWITCH 6" .
5 ❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunctioning parts.
6 ❏ Perform all road tests and enter the checks again for the required items. AT- 5 6
7 ❏
For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunctioning
parts. See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection pro-
cedures.) AT- 6 4
8
❏ Erase the results of the self-diagnostics from the TCM. AT- 4 1,
AT-
103

AT-94
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
TCM·ROM
TCM memory (ROM) is malfunctioning. P1703 —AT-132
TP SEN/CIRC A/T
TCM does not receive the proper accelerator pedal position sig-
nals (input by CAN communication) from ECM. P1705 P1705*3
AT-133
ATF TEMP SEN/
CIRC
During running, the AT fluid temperature sensor signal voltage is
excessively high or low P1710 P0710
AT-136
TURBINE REV S/
CIRC
TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine
revolution sensor 2. P1716 P1716
AT-141
VEH SPD SE/
CIR·MTR
Signal (CAN communication) from vehicle speed sensor MTR not
input due to cut line or the like

Unexpected signal input during running P1721 —
AT-143
A/T INTERLOCK
Except during shift change, the gear position and ATF pressure
switch states are monitored and comparative judgement made. P1730 P1730
AT-145
A/T 1ST E/BRAK-
ING
Each ATF pressure switch and solenoid current is monitored and
if a pattern is detected having engine braking 1st gear other than
in the M1 position, a malfunction is detected. P1731 —
AT-148
I/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1752 P1752
AT-150
I/C SOLENOID
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 3 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 3 is irregular during releasing accelerator
pedal. (Other than during shift change) P1754 P1754*2
AT-152
FR/B SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1757 P1757
AT-154
FR/B SOLENOID
FNCT

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 1 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 1 is irregular during releasing accelerator
pedal. (Other than during shift change) P1759 P1759*2
AT-156
D/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
value. P1762 P1762
AT-158
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II
(DTC)
Reference page
“A/T” with
CONSULT- II MIL indica-
tor lamp*1, “ENGINE”
with CON- SULT-II or GST

DTC P1705 THROTTLE POSITION SENSOR AT-133
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
DTC P1705 THROTTLE POSITION SENSORPFP:22620
DescriptionACS002O0
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle
position sensor, etc. The actuator sends a signal to the ECM, and ECM sends signals to TCM with CAN com-
munication.
CONSULT-II Reference ValueACS006C4
On Board Diagnosis LogicACS002O1

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P1705* TP SEN/CIRC A/T” with CONSULT-II or 15th judgement flicker without
CONSULT-II is detected when TCM does not receive the proper accelerator pedal position signals (input
by CAN communication) from ECM.
*: For VQ35DE engine.
Possible CauseACS002O2

Harness or connectors
(Sensor circuit is open or shorted.)
DTC Confirmation ProcedureACS002O3
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Touch “START”.
4. Start engine and let it idle for 1 second.
5. If DTC is detected, go to “ AT- 1 3 4 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name Condition Display value (Approx.)
ACCELE POSI Released accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8/8
BCIA0031E

AT-134
DTC P1705 THROTTLE POSITION SENSOR
Revision: 2005 July 2005 FX
Diagnostic ProcedureACS002O4
1. CHECK CAN COMMUNICATION LINE
Perform the self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 , "Diagnostic Pro-
cedure without CONSULT-II" .
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT- 1 0 6 , "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.
2. CHECK DTC WITH TCM
With CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Depress accelerator pedal and read out the value of “ACCELE POSI”.
4. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT- II. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE"
With GST
Follow the procedure “With CONSULT-II”.
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. CHECK DTC WITH ECM
With CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “SELF-DIAG RESULTS” mode for “ENGINE” with CON- SULT-II. Refer to EC-132, "
CONSULT-II Function (ENGINE)"
(for VQ35DE) or EC-822, "CONSULT-II Function (ENGINE)"
(for VK45DE).
With GST
Follow the procedure “With CONSULT-II”.
OK or NG
OK >> GO TO 4.
NG >> Check the DTC detected item. Refer to EC-132, "
CON-
SULT-II Function (ENGINE)" (for VQ35DE) or EC-822,
"CONSULT-II Function (ENGINE)" (for VK45DE).

If CAN communication line is detected, go to AT- 1 0 6 , "DTC U1000 CAN COMMUNICATION
LINE" .
4. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 3 3 , "DTC Confirmation Procedure" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 5.
Item name Condition Display value
(Approx.)
ACCELE POSI Released accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8/8
PCIA0070E
BCIA0030E

DTC P1705 THROTTLE POSITION SENSOR AT-135
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
5. CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to AT- 1 8 3 , "
MAIN POWER SUPPLY AND GROUND CIR-
CUIT" .
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
Check the following.

The A/T assembly harness connector pin terminals for damage or loose connection with harness connec-
tor.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 3 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.

AT-206
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
3. CHECK ACCELERATOR POSITION (APP) SENSOR
Check accelerator pedal position (APP) sensor. Refer to AT- 1 3 3 , "
DTC P1705 THROTTLE POSITION SEN-
SOR"
OK or NG
OK >> GO TO 4.
NG >> Repair or replace accelerator pedal position (APP) sensor.
4. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 5.
NG >> Refill ATF.
5. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT- 5 4 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
SAT638A
SAT494G