seat INFINITI FX35 2006 Service Manual

IP-1
INSTRUMENT PANEL
I BODY
CONTENTS
C
D E
F
G H
J
K L
M
SECTION IP
A
B
IP
Revision: 2006 December 2006 FX35/FX45
INSTRUMENT PANEL
PRECAUTIONS ..................................................... ..... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 2
Precautions ......................................................... ..... 2
PREPARATION ...................................................... ..... 3
Special Service Tools .......................................... ..... 3
Commercial Service Tools ................................... ..... 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 4
Work Flow ........................................................... ..... 4
CUSTOMER INTERVIEW ................................ ..... 4
DUPLICATE THE NOISE AND TEST DRIVE .. ..... 5
CHECK RELATED SERVICE BULLETINS ...... ..... 5
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ................................................. ..... 5
REPAIR THE CAUSE ...................................... ..... 5
CONFIRM THE REPAIR .................................. ..... 6
Generic Squeak and Rattle Troubleshooting ...... ..... 6 INSTRUMENT PANEL .....................................
..... 6
CENTER CONSOLE ........................................ ..... 6
DOORS ............................................................ ..... 6
TRUNK ............................................................. ..... 7
SUNROOF/HEADLINING ................................ ..... 7
SEATS .............................................................. ..... 7
UNDERHOOD .................................................. ..... 7
Diagnostic Worksheet .......................................... ..... 8
INSTRUMENT PANEL ASSEMBLY ...................... ... 10
Component Parts Drawing .................................. ... 10
Removal and Installation ..................................... ... 11
WORK STEP .................................................... ... 11
REMOVAL ........................................................ ... 12
INSTALLATION ................................................ ... 15
Disassembly and Assembly ................................. ... 16
A/T CONSOLE FINISHER ............................... ... 16
CENTER CONSOLE ........................................ ... 17
INSTRUMENT PASSENGER LOWER PANEL ... 18

IP-2
PRECAUTIONS
Revision: 2006 December 2006 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS001U7
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
PrecautionsNIS001U8

Disconnect both battery cables in advance.

Disconnect air bag system line in advance.

Never tamper with or force air bag lid open, as this may adversely affect air bag performance.

Be careful not to scratch pad and other parts.

When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.

When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.

Keep removed parts protected with cloth.

If a clip is deformed or damaged, replace it.

If an unreusable part is removed, replace it with a new one.

Tighten bolts and nuts firmly to the specified torque.

After re-assembly has been completed, make sure each part functions correctly.

Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.

Do not use any organic solvent, such as thinner or benzine.

SQUEAK AND RATTLE TROUBLE DIAGNOSES IP-7
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2006 December 2006 FX35/FX45
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. The trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting securing, or
insulating the component causing the noise.

LAN-1
LAN SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LAN
A
B
LAN
Revision: 2006 December 2006 FX35/FX45
LAN SYSTEM
CAN
PRECAUTIONS ..................................................... ..... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 3
Precautions When Using CONSULT-II ................ ..... 3
CHECK POINTS FOR USING CONSULT-II .... ..... 3
Precautions For Trouble Diagnosis ..................... ..... 3
CAN SYSTEM .................................................. ..... 3
Precautions For Harness Repair ......................... ..... 4
CAN SYSTEM .................................................. ..... 4
TROUBLE DIAGNOSES WORK FLOW ............... ..... 5
When Displaying CAN Communication System
Errors .................................................................. ..... 5
WHEN A MALFUNCTION IS DETECTED BY
CAN COMMUNICATION SYSTEM .................. ..... 5
WHEN A MALFUNCTION IS DETECTED
EXCEPT CAN COMMUNICATION SYSTEM ... ..... 5
TROUBLE DIAGNOSIS FLOW CHART .......... ..... 6
Diagnosis Procedure ........................................... ..... 7
SELECTING CAN SYSTEM TYPE (HOW TO
USE SPECIFICATION TABLE) ........................ ..... 7
ACQUISITION OF DATA BY CONSULT-II ....... ..... 8
HOW TO USE CHECK SHEET TABLE ........... ..... 9
CAN Diagnostic Support Monitor ........................ ... 16
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ECM ............................ ... 16
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR TCM ............................ ... 17
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR AWD CONTROL UNIT ... 18
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ICC UNIT .................... ... 19
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR INTELLIGENT KEY UNIT ... 20
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR BCM ............................ ... 21
DESCRIPTION OF “CAN DIAG SUPPORT MNTR” SCREEN FOR LDW CAMERA UNIT ...
... 22
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR UNIFIED METER AND A/
C AMP. .............................................................. ... 23
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT) ................ ... 24
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DRIVER SEAT CON-
TROL UNIT ...................................................... ... 24
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR IPDM E/R .................... ... 25
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DISPLAY CONTROL
UNIT ................................................................. ... 26
CAN COMMUNICATION ........................................ ... 27
System Description .............................................. ... 27
Component Parts and Harness Connector Location ... 27
Schematic ............................................................ ... 28
Wiring Diagram — CAN — .................................. ... 29
CAN Communication Unit .................................... ... 32
TYPE 1/TYPE 2 ................................................ ... 33
TYPE 3 ............................................................. ... 36
TYPE 4/TYPE 5 ................................................ ... 40
TYPE 6 ............................................................. ... 44
CAN SYSTEM (TYPE 1) ........................................ ... 49
Component Parts and Harness Connector Location ... 49
Schematic ............................................................ ... 49
Wiring Diagram — CAN — .................................. ... 49
Check Sheet ........................................................ ... 50
CHECK SHEET RESULTS (EXAMPLE) .......... ... 52
CAN SYSTEM (TYPE 2) ........................................ ... 69
Component Parts and Harness Connector Location ... 69
Schematic ............................................................ ... 69
Wiring Diagram — CAN — .................................. ... 69
Check Sheet ........................................................ ... 70
CHECK SHEET RESULTS (EXAMPLE) .......... ... 73
CAN SYSTEM (TYPE 3) ........................................ ... 91
Component Parts and Harness Connector Location ... 91
Schematic ............................................................ ... 91

LAN-2Revision: 2006 December 2006 FX35/FX45 Wiring Diagram — CAN — ..................................
... 91
Check Sheet ........................................................ ... 92
CHECK SHEET RESULTS (EXAMPLE) .......... ... 96
CAN SYSTEM (TYPE 4) ........................................ .117
Component Parts and Harness Connector Location .117
Schematic ............................................................ .117
Wiring Diagram — CAN — .................................. .117
Check Sheet ........................................................ .118
CHECK SHEET RESULTS (EXAMPLE) .......... .121
CAN SYSTEM (TYPE 5) ........................................ .139
Component Parts and Harness Connector Location .139
Schematic ............................................................ .139
Wiring Diagram — CAN — .................................. .139
Check Sheet ........................................................ .140
CHECK SHEET RESULTS (EXAMPLE) .......... .144
CAN SYSTEM (TYPE 6) ........................................ .163
Component Parts and Harness Connector Location .163
Schematic ............................................................ .163
Wiring Diagram — CAN — .................................. .163
Check Sheet ........................................................ .164
CHECK SHEET RESULTS (EXAMPLE) .......... .168
TROUBLE DIAGNOSIS FOR SYSTEM ................. .190
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .190
Inspection Between Data Link Connector and Uni- fied Meter and A/C Amp. Circuit ..........................
.190
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .190
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .191
ECM Circuit Inspection ........................................ .192
TCM Circuit Inspection ......................................... .193
Display Control Unit Circuit Inspection ................. .193
AWD Control Unit Circuit Inspection .................... .194
ICC Unit Circuit Inspection ................................... .194
Intelligent Key Unit Circuit Inspection .................. .195
Data Link Connector Circuit Inspection ................ .195
BCM Circuit Inspection ........................................ .196
Steering Angle Sensor Circuit Inspection ............. .196
LDW Camera Unit Circuit Inspection ................... .197
Unified Meter and A/C Amp. Circuit Inspection .... .197
ICC Sensor Circuit Inspection .............................. .198
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .198
Driver Seat Control Unit Circuit Inspection .......... .199
IPDM E/R Circuit Inspection ................................ .199
CAN Communication Circuit Inspection ............... .200
IPDM E/R Ignition Relay Circuit Inspection .......... .201

PRECAUTIONS LAN-3
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
[CAN]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS00345
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions When Using CONSULT-IINKS00346
When connecting CONSULT-II to data link connector, connect them through CONSULT-II CONVERTER.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
CHECK POINTS FOR USING CONSULT-II
1. Has CONSULT-II been used without connecting CONSULT-II CONVERTER on this vehicle?
–If YES, GO TO 2.
–If NO, GO TO 5.
2. Is there any indication other than indications relating to CAN communication system in the self-diagnosis results?
–If YES, GO TO 3.
–If NO, GO TO 4.
3. Based on self-diagnosis results unrelated to CAN communication, carry out the inspection.
4. Malfunctions may be detected in self-diagnosis depending on control units carrying out CAN communica- tion. Therefore, erase the self-diagnosis results.
5. Diagnose CAN communication system. Refer to LAN-5, "
TROUBLE DIAGNOSES WORK FLOW" .
Precautions For Trouble DiagnosisNKS00347
CAN SYSTEM

Do not apply voltage of 7.0 V or higher to the measurement terminals.

Use the tester with its open terminal voltage being 7.0 V or less.

Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.

LAN-24
[CAN]
TROUBLE DIAGNOSES WORK FLOW
Revision: 2006 December 2006 FX35/FX45
DESCRIPTION OF “CAN DIAG SUPPORT MNTR” SCREEN
FOR ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)
Display Results (Present)

OK: Normal

NG: Malfunction

UNKWN: The diagnosed unit does not transmit or receive the applicable data normally.
DESCRIPTION OF “CAN DIAG SUPPORT MNTR” SCREEN
FOR DRIVER SEAT CONTROL UNIT
Display Results (Present)

OK: Normal

NG: Malfunction

UNKWN: The diagnosed unit does not transmit or receive the applicable data normally.
SKIB2442E
“SELECT SYSTEM”
screen “CAN DIAG SUPPORT
MNTR” screen Description Present
ABS INITIAL DIAG Make sure that microcomputer in ECU works normally. OK/NG
TRANSMIT DIAG Make sure of normal transmission. OK/UNKWN
ECM Make sure of normal reception from ECM. OK/UNKWN
TCM Make sure of normal reception from TCM. OK/UNKWN
METER/M&A METER/M&A is not diagnosed. UNKWN
STRG Make sure of normal reception from steering angle sensor. OK/UNKWN
ICC ICC is not diagnosed. UNKWN
AWD/4WD Make sure of normal reception from AWD control unit. OK/UNKWN
SKIB2360E
“SELECT SYSTEM” screen “CAN DIAG SUPPORT
MNTR” screen Description Present
AUTO DRIVE POS. INITIAL DIAG Make sure that microcomputer in ECU works normally. OK/NG
TRANSMIT DIAG Make sure of normal transmission. OK/UNKWN
BCM/SEC Make sure of normal reception from BCM. OK/UNKWN
METER/M&A Make sure of normal reception from unified meter and A/C amp. OK/UNKWN
TCM Make sure of normal reception from TCM. OK/UNKWN

CAN COMMUNICATION LAN-27
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
CAN COMMUNICATIONPFP:23710
System DescriptionNKS0034C
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Component Parts and Harness Connector LocationNKS003MM
1. AWD control unit M92 (AWD mod-
els) 2. ICC unit M88 (with ICC system) 3. ECM M90
4. IPDM E/R E9 5. ICC sensor E39 (with ICC system) 6. Display control unit M76
7. Unified meter and A/C amp. M55 8. Steering angle sensor M14 9. Intelligent Key unit M34 (with Intelli- gent Key system)
10. ABS actuator and electric unit E56 (control unit) 11. BCM M3 12. Data link connector M5
13. LDW camera unit R9 (with Lane departure warning system) 14. Driver seat control unit B152 15. A/T assembly F44
PKIC9643E

CAN COMMUNICATION LAN-33
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2006 December 2006 FX35/FX45
TYPE 1/TYPE 2
System Diagram

Ty pe 1

Ty pe 2
Input/Output Signal Chart
T: Transmit R: Receive
PKIC9663E
PKIC9635E
Signals ECM TCM Dis-
play
control unit Intelli-
gent Key unit BCM St e e r-
ing
angle
sensor Unified
meter
and A/
C amp. ABS
actua-
tor and
electric unit
(con-
trol
unit) Driver
seat
control unit IPDM
E/R
A/C compressor feedback sig-
nal TR
A/C compressor request signal T R
Accelerator pedal position sig-
nal TR R
ASCD CRUISE lamp signal T R
ASCD OD cancel request sig-
nal TR

LAN-34
[CAN]
CAN COMMUNICATION
Revision: 2006 December 2006 FX35/FX45
ASCD operation signal T R
ASCD SET lamp signal T R
Battery voltage signal T R
Closed throttle position signal T R
Cooling fan speed request sig-
nal T
R
Engine coolant temperature
signal TR
Engine speed signal T R R R R
Engine status signal T R
Fuel consumption monitor sig-
nal TR
RT
Malfunctioning indicator lamp
signal TR
Wide open throttle position sig-
nal TR
A/T CHECK indicator lamp sig-
nal TR
A/T self-diagnosis signal R T
Current gear position signal T R
Manual mode indicator signal T R
Output shaft revolution signal R T
P range signal T R R
Shift position indicator signal T R
Turbine revolution signal R T
A/C switch/indicator signal TR
RT
System setting signal TR R
RT T
Alarm request signal T R
Back door open request signal T R
Door lock/unlock request signal T R
Ignition knob switch signal T R
Key warning signal T R
Power window open request
signal TR
Sleep wake up signal TR R
TR
Buzzer output signal TR
TR
A/C switch signal R T Signals ECM TCM
Dis-
play
control unit Intelli-
gent
Key unit BCM Steer-
ing
angle
sensor Unified
meter
and A/
C amp. ABS
actua-
tor and
electric
unit
(con- trol
unit) Driver
seat
control unit IPDM
E/R