clock setting INFINITI FX35 2006 Service Manual

TRANSMISSION ASSEMBLY AT-267
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
10. Remove crankshaft position sensor (POS) from A/T assembly. CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.

Do not place in an area affected by magnetism.
11. Remove starter motor. Refer to SC-15, "
VQ35DE ENGINE
MODELS (2WD)" .
12. Remove fluid cooler tube.
13. Remove rear plate cover. Refer to EM-30, "
Removal and Instal-
lation (2WD Models)" .
14. Remove rear cover plate. Refer to EM-30, "
Removal and Installation (2WD Models)" .
15. Turn crankshaft, and remove the four tightening bolts for drive plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
16. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
17. Remove rear engine mounting member with power tool.
18. Remove engine mounting insulator (rear).
19. Remove air breather hose. Refer to AT- 2 6 4 , "
Removal and Installation" .
20. Disconnect A/T assembly harness connector.
21. Remove A/T fluid charging pipe from A/T assembly.
22. Remove O-ring from A/T fluid charging pipe.
23. Plug up openings such as the A/T fluid charging pipe hole, etc.
24. Remove bolts fixing A/T assembly to engine assembly with power tool.
25. Remove A/T assembly from vehicle with a transmission jack.

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a A/T, be sure to check dis-
tance “A” to ensure it is within the reference value limit.
SCIA2155E
SCIA2288E
SCIA0499E
Distance “A” : 25.0 mm (0.98 in) or more
SAT017B

TRANSMISSION ASSEMBLY AT-271
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2006 December 2006 FX35/FX45
11. Remove crankshaft position sensor (POS) from A/T assembly. CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
12. Remove starter motor. Refer to SC-16, "
VQ35DE ENGINE
MODELS (AWD)" (for VQ35DE) or SC-14, "VK45DE ENGINE
MODELS" (for VK45DE).
13. Disconnect fluid cooler tube from A/T assembly.
14. Remove rear plate cover. Refer to EM-36, "
Removal and Instal-
lation (AWD Models)" (for VQ35DE) or EM-187, "Removal and
Installation" (for VK45DE).
15. Turn crankshaft, and remove the four tightening bolts for drive plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
16. Remove dynamic damper (for VQ35DE). Refer to EM-118,
"Removal and Installation (AWD Models)" .
17. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow
it to collide against the drain plug.
18. Remove rear engine mounting member with power tool.
19. Remove engine mounting insulator (rear).
20. Tilt the A/T assembly slightly to keep the clearance between body and A/T assembly, and then disconnect air breather hose
from A/T fluid charging pipe. Refer to AT- 2 6 4 , "
Removal and
Installation" .
21. Disconnect A/T assembly harness connector and transfer assembly harness connector.
22. Remove A/T fluid charging pipe.
23. Remove O-ring from A/T fluid charging pipe.
24. Plug up openings such as the A/T fluid charging pipe hole, etc.
25. Remove bolts fixing transmission assembly to engine with power tool.
SCIA2011E
SCIA5326E
SCIA2010E
SCIA2202E

DI-2Revision: 2006 December 2006 FX35/FX45 Oil Pressure Warning Lamp Does Not Turn Off (Oil
Pressure Is Normal) ............................................. ... 49
Component Inspection ......................................... ... 51
OIL PRESSURE SWITCH ................................ ... 51
A/T INDICATOR ..................................................... ... 52
System Description .............................................. ... 52
MANUAL MODE ............................................... ... 52
NOT MANUAL MODE ...................................... ... 52
Wiring Diagram — AT/IND — .............................. ... 53
A/T Indicator Is Malfunction ................................. ... 55
WARNING CHIME .................................................. ... 56
System Description .............................................. ... 56
POWER SUPPLY AND CIRCUIT ..................... ... 56
IGNITION KEY WARNING CHIME (WITHOUT
INTELLIGENT KEY) ......................................... ... 57
IGNITION KEY WARNING CHIME (WITH INTEL-
LIGENT KEY) ................................................... ... 57
LIGHT WARNING CHIME ................................ ... 58
SEAT BELT WARNING CHIME ........................ ... 58
Component Parts and Harness Connector Location ... 59
Schematic ............................................................ ... 60
Wiring Diagram — CHIME — .............................. ... 61
Terminals and Reference Value for BCM ............. ... 64
Terminals and Reference Value for Unified Meter
and A/C Amp. ...................................................... ... 68
Terminals and Reference Value for Combination
Meter ................................................................... ... 69
CONSULT-II Function (METER A/C AMP) .......... ... 69
CONSULT-II Function (BCM) ............................... ... 69
DIAGNOSIS ITEMS DESCRIPTION ................ ... 69
CONSULT-II BASIC OPERATION .................... ... 69
DATA MONITOR ............................................... ... 69
ACTIVE TEST .................................................. ... 70
SELF-DIAG RESULTS ..................................... ... 70
Trouble Diagnosis ................................................ ... 70
HOW TO PERFORM TROUBLE DIAGNOSIS . ... 70
PRELIMINARY INSPECTION .......................... ... 71
Symptom Chart .................................................... ... 71
Power Supply and Ground Circuit Inspection ...... ... 71
Combination Meter Buzzer Circuit Inspection ...... ... 72
Front Door Switch (Driver Side) Signal Inspection ... 74
Key Switch Signal Inspection (Without Intelligent
Key) ..................................................................... ... 75
Key Switch and Ignition Knob Switch Signal Inspec-
tion (With Intelligent Key, When Mechanical Key Is
Used) ................................................................... ... 76
Lighting Switch Signal Inspection ........................ ... 77
Seat Belt Buckle Switch (Driver Side) Signal Inspec-
tion ....................................................................... ... 78
Component Inspection ......................................... ... 79
FRONT DOOR SWITCH (DRIVER SIDE) ........ ... 79
KEY SWITCH ................................................... ... 79
KEY SWITCH AND IGNITION KNOB SWITCH ... 79
SEAT BELT BUCKLE SWITCH (DRIVER SIDE) ... 79
LANE DEPARTURE WARNING SYSTEM ............. ... 80
Precautions for Lane Departure Warning (LDW)
system ................................................................. ... 80
System Description .............................................. ... 80 LDW SYSTEM OPERATION ............................
... 80
POWER SUPPLY AND GROUND CIRCUIT .... ... 82
Action Test ........................................................... ... 83
LDW SYSTEM RUNNING TEST ...................... ... 83
Camera Aiming Adjustment ................................. ... 83
OUTLINE .......................................................... ... 83
PREPARATION ................................................. ... 83
TARGET SETTING ........................................... ... 83
VEHICLE HEIGHT CHECK .............................. ... 86
AIMING ADJUSTMENT .................................... ... 86
Component Parts and Harness Connector Location ... 90
Schematic ............................................................ ... 91
Wiring Diagram — LDW — .................................. ... 92
Terminals and Reference Value for LDW Camera
Unit ....................................................................... ... 95
CONSULT-II Function (LDW) ............................... ... 95
DESCRIPTION ................................................. ... 95
CONSULT-II BASIC OPERATION .................... ... 95
WORK SUPPORT ............................................ ... 95
SELF-DIAG RESULTS ...................................... ... 95
DATA MONITOR ............................................... ... 96
ACTIVE TEST ................................................... ... 97
Trouble Diagnosis ................................................ ... 98
HOW TO PERFORM TROUBLE DIAGNOSIS . ... 98
SYMPTOM CHART ........................................... ... 98
Preliminary Inspection .......................................... ... 98
Power Supply and Ground Circuit Inspection ...... ... 99
DTC [C1B00] CAMERA UNIT MALF ................... .100
DTC [C1B01] CAM AIMING INCMP .................... .100
DTC [C1B02] VHCL SPD DATA MALF ................ .100
DTC [C1B03] ABNRML TEMP DETECT ............. .101
DTC [U1000] CAN COMM CIRCUIT ................... .101
DTC [U1010] CONTROL UNIT (CAN) ................. .101
LDW Chime Circuit Inspection ............................. .101
LDW Switch Circuit Inspection ............................. .102
LDW Indicator Lamp Circuit Inspection ................ .105
Turn Signal Input Inspection ................................ .106
Electrical Component Inspection ......................... .106
LDW SWITCH ................................................... .106
Removal and Installation for LDW Camera Unit .. .107
REMOVAL ......................................................... .107
INSTALLATION ................................................. .107
Removal and Installation for LDW Chime ............ .107
REMOVAL ......................................................... .107
INSTALLATION ................................................. .107
Removal and Installation for LDW Switch ............ .107
CAN COMMUNICATION ........................................ .108
System Description .............................................. .108
CAN Communication Unit .................................... .108
COMPASS .............................................................. .109
Precautions for Compass ..................................... .109
System Description .............................................. .109
Troubleshooting ................................................... .110
Zone Variation Setting Procedure ........................ . 111
Calibration Procedure .......................................... . 111
Wiring Diagram — COMPAS — ........................... .112
Removal and Installation of Compass .................. .113
CLOCK ................................................................... .114

INTERIOR ROOM LAMP LT-185
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45
4. CHECK STEP LAMP CIRCUIT
1. Disconnect BCM connector and front door driver side step lamp connector.
2. Check continuity between BCM harness connector M4 terminal 41 and front door driver side step lamp harness connector D9
terminal 1.
OK or NG
OK >> Replace BCM if step lamp does not work after setting the connector again. Refer to BCS-15, "
Removal and
Installation of BCM" .
NG >> Repair harness or connector.
All Interior Room Lamps Do Not OperateNKS002YZ
1. CHECK POWER SUPPLY CIRCUIT
1. All interior room lamps switch are OFF.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector M4 terminal 41 and ground.
OK or NG
OK >> Repair harness or connector. In a case of making a short circuit, be sure to disconnect cable from the nega-
tive terminal repairing harness, and then reconnect.
NG >> Replace BCM. Refer to BCS-15, "
Removal and Installa-
tion of BCM" .
Bulb ReplacementNKS002Z0
IGNITION KEY HOLE ILLUMINATION (WITHOUT INTELIGENT KEY)
1. Remove combination meter. Refer to DI-25, "Removal and
Installation of Combination Meter" .
2. Remove screw and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
4. Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION (WITH INTELIGENT KEY)
1. Remove instrument lower panel (driver side). Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Installation is the reverse order of removal. 41 – 1 : Continuity should exist.
PKIB3523E
41 – Ground : Battery voltage.
PKIB3524E
Ignition key hole illumination : 12 V - 0.8 W
SKIA5575E
Ignition key hole illumination : 12 V - 0.8 W
PKIC9733E

LT-190
ILLUMINATION
Revision: 2006 December 2006 FX35/FX45

to clock (illumination) terminal 3

to hazard switch (illumination) terminal 3

to heated seat switch (driver side) (illumination) terminal 5

to heated seat switch (passenger side) (illumination) terminal 5

to door mirror remote control switch (illumination) terminal 16

to LDW switch (illumination) terminal 5

to combination switch (spiral cable) terminal 26

to microphone terminal 2 (with telephone system)

to A/C and AV switch (illumination) terminal 3

to DVD player (illumination) terminal 12

to coin box illumination terminal 2

to rear power window switch LH and RH (illumination) terminals 6,

through combination switch (spiral cable) terminal 18

to audio steering switch (illumination), and

to icc steering switch (illumination) (with icc)

to ascd steering switch (illumination) (without icc)
Illumination control

through combination meter terminal 19

to A/T device (illumination) terminal 12

to snow mode switch (illumination) terminal 6

to VDC off switch (illumination) terminal 4

to clock (illumination) terminal 4

to hazard switch (illumination) terminal 4

to heated seat switch (driver side) (illumination) terminal 6

to heated seat switch (passenger side) (illumination) terminal 6

to door mirror remote control switch terminal 15

to LDW switch (illumination) terminal 4,

to combination switch (spiral cable) terminal 27

to A/C and AV switch (illumination) terminal 4

to DVD player (illumination) terminal 10,

through combination switch (spiral cable) terminal 21

to audio steering switch (illumination), and

to icc steering switch (illumination) (with icc)

to ascd steering switch (illumination) (without icc)
Ground is supplied at all times

to glove box lamp terminal 2, and

to coin box illumination terminal 3

through grounds M35, M45 and M85,

to rear power window switch LH and RH (illumination) terminals 7

through grounds B15 and B45.
With power and ground supplied, illumination lamps illuminate.
EXTERIOR LAMP BATTERY SAVER CONTROL
When the lighting switch is in the 1ST or 2ND position (or if auto light system is activated), and ignition switch
is turned from ON or ACC to OFF, battery saver control function is activated.
Under this condition, illumination lamps remain illuminated for 5 minutes, then illumination lamps are turned
off.
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by battery saver control, and illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.