light INFINITI G37 2010 Repair Manual

COAT HOOKS
Sedan The coat hooks are equipped beside the rear
personal lights.
CAUTIONDo not place items which are more than 2 lb (1
kg) on the hook. Coupe To use the coat hook, push the hook
 A
to
release.
CAUTIONAvoid hanging heavy goods on the hook.
STOWING GOLF BAGS (Coupe) Normally, two standard golf bags can be stowed
in the trunk. Insert the top of the golf bag into
left side of the trunk room
 1
then put the bag
forward
 2
. Insert the top of the 2nd golf bag
into right side of the trunk room
 3
and pull it
in all the way
 4
.
In some cases, you may not be able to stow two
golf bags in your vehicle, depending on their
sizes or types.Sedan SIC3248
Coupe SIC3544
SIC3467
2-48 Instruments and controls
 —
—
10/12/09—tbrooks


Automatic operation (for front door
windows or all door windows) To fully open or close the window, completely
push down or pull up the switch and release it;
it need not be held. The window will automati-
cally open or close all the way. To stop the
window, just push or lift the switch in the
opposite direction.
A light push or pull on the switch will cause the
window to open or close until the switch is
released. Auto reverse function WARNINGThere are some small distances immediately
before the closed position which cannot be de-
tected. Make sure that all passengers have
their hands, etc., inside the vehicle before clos-
ing the window.
If the control unit detects something caught in
the window as it is closing, the window will be
immediately lowered.
The auto reverse function can be activated when
the window is closed by automatic operation
when the ignition switch is in the ON position or
for 45 seconds after the ignition switch is
pushed to the OFF position.
Depending on the environment or driving condi-
tions, the auto reverse function may be activated
if an impact or load similar to something being
caught in the window occurs.Sedan — Type A SIC3289
Sedan — Type B SIC3285 Coupe SIC3288
Instruments and controls
2-51
 —
—
10/12/09—tbrooks


Automatic adjusting function (Coupe) CAUTIONWhen the battery cable is removed from the
battery terminal, do not close either of the front
doors. The automatic window adjusting func-
tion will not work and the side roof panel may
be damaged.
The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to
avoid contact between the window and the side
roof panel. When the door is closed, the window
is automatically raised slightly.
While the automatic adjusting function does not
work, the window will be controlled as follows:
● When the door is opened, the window lowers
for approximately 2 seconds.
● While the door is open, the window cannot
be raised. If the windows do not close
automatically If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power win-
dow system.
1. Push the ignition switch to the ON posi-
tion.
2. Close the door.
3. Open the window completely by operating
the power window switch.
4. Pull the power window switch and hold it
to close the window, and then hold the
switch more than 3 seconds after the
window is closed completely.
5. Release the power window switch. Oper-
ate the window by the automatic function
to confirm the initialization is complete.
6. Perform steps 2 through 5 above for other
windows.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked by an
INFINITI retailer. WARNING● In an accident you could be thrown from the
vehicle through an open moonroof. Always
use seat belts and child restraints.
● Do not allow anyone to stand up or extend
any portion of their body out of the moonroof
opening while the vehicle is in motion or
while the moonroof is closing.
CAUTION● Remove water drops, snow, ice or sand from
the moonroof before opening.
● Do not place any heavy object on the moon-
roof or surrounding area.MOONROOF (if so equipped)
2-52 Instruments and controls
 —
—
10/12/09—tbrooks


If the moonroof does not operate If the moonroof does not operate properly,
perform the following procedure to initialize the
moonroof operation system.
1. If the moonroof is open, close it fully by
repeatedly pushing the CLOSE
 1
side of the moonroof switch to tilt the
moonroof up.
2. Push and hold the CLOSE
 1
side
of the moonroof switch.
3. Release the moonroof switch after the
moonroof moves slightly up and down.
4. Push and hold the OPEN
 2
side of
the moonroof switch to fully tilt the moon-
roof down.
5. Check if the moonroof switch operates
normally.
If the moonroof does not operate properly after
performing the procedure above, have your
vehicle checked by an INFINITI retailer.
MAP LIGHTS Push the button as illustrated to turn the light
on or off.
PERSONAL LIGHTS (Sedan)
Rear Push the button as illustrated to turn the light
on or off. SIC3249 SIC3250
INTERIOR LIGHTS
2-54 Instruments and controls
 —
—
10/12/09—tbrooks


INTERIOR LIGHT CONTROL SWITCH The interior light control switch has three posi-
tions: ON, DOOR and OFF.
ON position When the switch is in the ON position
 1
the map
lights and rear personal lights will illuminate.
DOOR position When the switch is in the DOOR position
 2
, the
map lights and rear personal lights will illumi-
nate under the following conditions:
● ignition switch is switched to the LOCK
position
– remain on for about 15 seconds. ● doors are unlocked by pushing the UNLOCK
button on the Intelligent Key or door handle
request switch with the ignition switch in the
LOCK position
– remain on for about 15 seconds.
● any door is opened and then closed with the
ignition switch in the LOCK position
– remain on for about 15 seconds.
● any door is opened with the ignition switch
in the ACC or ON position
– remain on while the door is opened.
When the door is closed, the lights go off.
The lights will also turn off after 15 minutes when
the lights remain illuminated after the ignition
switch has been pushed to the OFF or LOCK po-
sition to prevent the battery from becoming dis-
charged.
When the auto interior illumination is set to the
OFF position (see “VEHICLE INFORMATION AND
SETTINGS” in the “4. Monitor, climate, audio,
phone and voice recognition systems” section),
the lights will illuminate under the following
condition:
● any door is opened with the ignition switch
in any position
– remain on while the door is opened.
When the door is closed, the lights go off. OFF position When the switch is in the OFF position
 3
, the
lights will not illuminate, regardless of the
condition.
CAUTIONDo not use for extended periods of time with
the engine stopped. This could result in a dis-
charged battery.SIC3251
Instruments and controls
2-55
 —
—
10/12/09—tbrooks


The light on the vanity mirror will turn on when
the cover on the vanity mirror is opened.
When the cover is closed, the light will turn off.
The lights will also turn off after 15 minutes when
the lights remain illuminated to prevent the bat-
tery from becoming discharged. The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the light
will turn off.
The light will also turn off after 15 minutes when
the light remains illuminated after the ignition
switch has been pushed to the OFF or LOCK po-
sition to prevent the battery from becoming dis-
charged.
Type A SIC2064
Type B SIC2555AVANITY MIRROR LIGHTS TRUNK LIGHT
2-56 Instruments and controls
 —
—
10/12/09—tbrooks


HomeLink  Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters
into one built-in device.
HomeLink  Universal Transceiver:
● Will operate most Radio Frequency (RF) de-
vices such as garage doors, gates, home and
office lighting, entry door locks and security
systems.
● Is powered by your vehicle’s battery. No
separate batteries are required. If the vehi-
cle’s battery is discharged or is discon-
nected, HomeLink  will retain all program-
ming.
Once HomeLink  Universal Transceiver is pro-
grammed, retain the original transmitter for fu-
ture programming procedures (Example: new ve-
hicle purchases). Upon sale of the vehicle, the
programmed HomeLink  Universal Transceiver
buttons should be erased for security purposes.
For additional information, see “PROGRAMMING
HomeLink  ” later in this section. WARNING● Do not use HomeLink  Universal Transceiver
with any garage door opener that lacks
safety stop and reverse features as required
by federal safety standards. (These stan-
dards became effective for opener models
manufactured after April 1, 1982.) A garage
door opener which cannot detect an object in
the path of a closing garage door and then
automatically stop and reverse, does not
meet current federal safety standards. Using
a garage door opener without these features
increases the risk of serious injury or death.
● During programming procedure, your garage
door or security gate may open or close.
Make sure that people and objects are clear
of the garage door, gate, etc. that you are
programming.
● Your vehicle’s engine should be turned off
while programming HomeLink  Universal
Transceiver. PROGRAMMING HOMELINK To program your HomeLink  Transceiver to op-
erate a garage door, gate, or entry door opener,
home or office lighting, you need to be at the
same location as the device. Note: Garage door
openers (manufactured after 1996) have “rolling
code protection”. To program a garage door
opener equipped with “rolling code protection”;
you will need to use a ladder to get up to the
garage door opener motor to be able to access
the “smart or learn” program button.HOMELINK  UNIVERSAL TRANSCEIVER (if
so equipped)
Instruments and controls
2-57
 —
—
10/12/09—tbrooks


1. To begin, push and hold the 2 outer
HomeLink  buttons (to clear the memory)
until the indicator light
 A
blinks (after 20
seconds). Release both buttons.
2. Position the end of the hand-held trans-
mitter 1-3 inches away from the
HomeLink  surface. 3. Using both hands, simultaneously push
and hold both the HomeLink  button you
want to program and the hand-held trans-
mitter button.
DO NOT release the buttons until step 4
has been completed.
4. Hold down both buttons until the indicator
light on HomeLink  flashes, changing from
a “slow blink” to a “rapid blink”. This
could take up to 90 seconds. When the
indicator light blinks rapidly, both buttons
may be released. The rapidly flashing light
indicates successful programming. To ac-
tivate the garage door or other pro-
grammed device, push and hold the pro-
grammed HomeLink  button - releasing
when the device begins to activate. 5. If the indicator light on HomeLink  blinks
rapidly for two seconds and then turns
solid, HomeLink  has picked up a “rolling
code” garage door opener signal. You will
need to proceed with the next steps to
train HomeLink  , completing the pro-
gramming may require a ladder and an-
other person for convenience.
6. Push and release the program button
located on the garage door opener’s mo-
tor to activate the “training mode”. This
button is usually located near the an-
tenna wire that hangs down from the
motor. If the wire originates from under a
light lens, you will need to remove the
lens to access the training button.
NOTE:
Once you have pushed and released the
training button on the garage door open-
er’s motor and the “training light” is lit,
you have 30 seconds in which to perform
step 7. For convenience, use the help of a
second person to assist when performing
this step.SIC3612 SIC3613
2-58 Instruments and controls
 —
—
10/12/09—tbrooks


7. Quickly (within 30 seconds of pushing
and releasing the garage door opener
training button) and firmly push and re-
lease the HomeLink  button you’ve just
programmed. Push and release the
HomeLink  button up to three times to
complete the training.
8. Your HomeLink  button should now be
programmed. To program the remaining
HomeLink  buttons for additional door or
gate openers, follow steps 2 through 8
only.
NOTE:
Do not repeat step 1 unless you want to “clear”
all previously programmed HomeLink  buttons.
If you have any questions or are having diffi-
culty programming your HomeLink  buttons,
please refer to the HomeLink  web site at:
www.homelink.com or call 1-800-355-3515.
PROGRAMMING HOMELINK  FOR
CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand-
held transmitters to stop transmitting after 2
seconds. To program your hand-held transmit-
ter to HomeLink  , continue to push and hold
the HomeLink  button (note steps 2 through 4
under “Programming HomeLink  ”) while you push and re-push (“cycle”) your hand-held
transmitter every 2 seconds until the indicator
light flashes rapidly (indicating successful pro-
gramming).
NOTE:
If programming a garage door opener, etc., it is
advised to unplug the device during the “cy-
cling” process to prevent possible damage to
the garage door opener components.
OPERATING THE HOMELINK 
UNIVERSAL TRANSCEIVER HomeLink  Universal Transceiver (once pro-
grammed) may now be used to activate the
garage door, etc. To operate, simply push the
appropriate programmed HomeLink  Universal
Transceiver button. The red indicator light will
illuminate while the signal is being transmitted.
PROGRAMMING TROUBLE-DIAGNOSIS If HomeLink  does not quickly learn the hand-
held transmitter information:
● replace the hand-held transmitter batteries
with new batteries.
● position the hand-held transmitter with its
battery area facing away from the
HomeLink  surface. ● push and hold both the HomeLink  and
hand-held transmitter buttons without inter-
ruption.
● position the hand-held transmitter 2 to 5 in
(50 to 127 mm) away from the HomeLink 
surface. Hold the transmitter in that position
for up to 15 seconds. If HomeLink  is not
programmed within that time, try holding
the transmitter in another position - keeping
the indicator light in view at all times.
If you continue to have programming difficul-
ties, please contact the INFINITI Consumer Af-
fairs Department. The phone numbers are lo-
cated in the Foreword of this Owner’s Manual.
CLEARING THE PROGRAMMED
INFORMATION Individual buttons cannot be cleared, however
to clear all programming, push and hold the two
outside buttons and release when the indicator
light begins to flash (in approximately 20 sec-
onds).
Instruments and controls
2-59
 —
—
10/12/09—tbrooks


REPROGRAMMING A SINGLE
HOMELINK  BUTTONTo reprogram a HomeLink  Universal Trans-
ceiver button, complete the following.
1. Push and hold the desired HomeLink 
button. Do not release the button until
step 4 has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink  surface.
3. Push and hold the hand-held transmitter
button.
4. The HomeLink  indicator light will flash,
first slowly and then rapidly. When the
indicator light begins to flash rapidly,
release both buttons.
The HomeLink  Universal Transceiver button
has now been reprogrammed. The new device
can be activated by pushing the HomeLink 
button that was just programmed. This proce-
dure will not affect any other programmed
HomeLink  buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink  . Consult the
Owner’s Manual of each device or call the
manufacturer or retailer of those devices for
additional information.
When your vehicle is recovered, you will need to
reprogram the HomeLink  Universal Transceiver
with your new transmitter information.
FCC Notice:
This device complies with FCC rules part 15. Op-
eration is subject to the following two condi-
tions: (1) This device may not cause harmful in-
terference and (2) This device must accept any
interference that may be received, including in-
terference that may cause undesired operation.
The transmitter has been tested and complies
with FCC and DOC/MDC rules. Changes or modi-
fications not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the device.
DOC: ISTC 1763K1313
FCC I.D.: CB2V67690
2-60 Instruments and controls
 —
—
10/12/09—tbrooks