change time INFINITI G37 2012 Owners Manual

Black plate (4,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]. ALWAYS provide information about the
proper use of vehicle safety features to
all occupants of the vehicle.
. ALWAYS review this Owner ’ s Manual for
important safety information.
MODIFICATION OF YOUR VEHICLE This vehicle should not be modified.
Modification could affect its performance,
safety or durability, and may even violate
governmental regulations. In addition,
damage or performance problems result-
ing from modification will not be covered
under the INFINITI warranties.
WHEN READING THE MANUAL GUID-EA2A5347-A23E-4B25-B5B5-2D387C7A767C
This manual includes information for all
options available on this model. Therefore,
you may find some information that does
not apply to your vehicle.
All information, specifications and illustra-
tions in this manual are those in effect at
the time of printing. INFINITI reserves the
right to change specifications or design at
any time without notice. IMPORTANT INFORMATION ABOUT
THIS MANUAL GUID-7A07B2BC-A0CA-4D51-BC19-17D5E32FD79D
You will see various symbols in this
manual. They are used in the following
ways:
WARNING This is used to indicate the presence of a
hazard that could cause death or serious
personal injury. To avoid or reduce the risk,
the procedures must be followed precisely.
CAUTION This is used to indicate the presence of a
hazard that could cause minor or moderate
personal injury or damage to your vehicle.
To avoid or reduce the risk, the procedures
must be followed carefully. SIC0697
If you see the symbol above, it means “ Do
not do this ” or “ Do not let this happen ” . NOS1274
If you see a symbol similar to those above
in an illustration, it means the arrow points
to the front of the vehicle. NOS1275
Arrows in an illustration that are similar to
those above indicate movement or action. NOS1276
Arrows in an illustration that are similar to

Black plate (37,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]WARNING. Every person who drives or rides in this
vehicle should use a seat belt at all
times. Children should be properly re-
strained in the rear seat and, if appro-
priate, in a child restraint.
. The seat belt should be properly ad-
justed to a snug fit. Failure to do so may
reduce the effectiveness of the entire
restraint system and increase the chance
or severity of injury in an accident.
Serious injury or death can occur if the
seat belt is not worn properly.
. Always route the shoulder belt over your
shoulder and across your chest. Never
run the belt behind your back, under
your arm or across your neck. The belt
should be away from your face and neck,
but not falling off your shoulder.
. Position the lap belt as low and snug as
possible AROUND THE HIPS, NOT THE
WAIST. A lap belt worn too high could
increase the risk of internal injuries in an
accident.
. Be sure the seat belt tongue is securely
fastened to the proper buckle. . Do not wear the seat belt inside out or
twisted. Doing so may reduce its effec-
tiveness.
. Do not allow more than one person to
use the same seat belt.
. Never carry more people in the vehicle
than there are seat belts.
. If the seat belt warning light glows
continuously while the ignition is turned
ON with all doors closed and all seat
belts fastened, it may indicate a mal-
function in the system. Have the system
checked by an INFINITI retailer.
. No changes should be made to the seat
belt system. For example, do not modify
the seat belt, add material or install
devices that may change the seat belt
routing or tension. Doing so may affect
the operation of the seat belt system.
Modifying or tampering with the seat
belt system may result in serious perso-
nal injury.
. Once a seat belt pretensioner has
activated, it cannot be reused and must
be replaced together with the retractor.
See an INFINITI retailer.
. Removal and installation of the preten-
sioner seat belt system components should be done by an INFINITI retailer.
. All seat belt assemblies, including re-
tractors and attaching hardware, should
be inspected after any collision by an
INFINITI retailer. INFINITI recommends
that all seat belt assemblies in use
during a collision be replaced unless
the collision was minor and the belts
show no damage and continue to oper-
ate properly.
Seat belt assemblies not in use during a
collision should also be inspected and
replaced if either damage or improper
operation is noted.
. All child restraints and attaching hard-
ware should be inspected after any
collision. Always follow the restraint
manufacturer ’ s inspection instructions
and replacement recommendations. The
child restraints should be replaced if
they are damaged.
Safety — Seats, seat belts and supplemental restraint system
1-15

Black plate (79,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2 Instruments and controls Cockpit ................................................................... 2-3
Instrument panel .................................................... 2-4
Meters and gauges ................................................. 2-6
Speedometer and odometer ............................... 2-7
Tachometer ......................................................... 2-8
Engine coolant temperature gauge ..................... 2-8
Fuel gauge ......................................................... 2-9
Compass (if so equipped) ....................................... 2-9
Zone variation change procedure ...................... 2-11
Warning/indicator lights and
audible reminders ................................................ 2-12
Checking bulbs ................................................. 2-12
Warning lights .................................................. 2-12
Indicator lights ................................................. 2-18
Audible reminders ............................................ 2-19
Dot matrix liquid crystal display ........................... 2-20
Indicators for operation .................................... 2-22
Indicators for maintenance ............................... 2-24
Trip computer ................................................... 2-26
Security systems .................................................. 2-28
Vehicle Security System ................................... 2-28
INFINITI Vehicle Immobilizer System ................. 2-30
Windshield wiper and washer switch .................... 2-31
Rain-sensing auto wiper system
(if so equipped) ................................................ 2-33 Rear window and outside mirror
defroster switch ................................................... 2-34
Headlight and turn signal switch .......................... 2-34
Xenon headlights ............................................ 2-34
Headlight switch ............................................. 2-35
Turn signal switch ........................................... 2-38
Fog light switch .............................................. 2-39
Hazard warning flasher switch ............................. 2-39
Horn .................................................................... 2-40
Heated seats (if so equipped) .............................. 2-40
SNOW mode switch (if so equipped) .................... 2-41
Vehicle Dynamic Control (VDC) OFF switch ............ 2-42
Clock .................................................................... 2-42
Adjusting the time .......................................... 2-42
Power outlet ........................................................ 2-43
Cigarette lighter and ashtrays (if so equipped) ....... 2-44
Front ............................................................... 2-44
Rear ................................................................ 2-44
Storage ................................................................ 2-45
Cup holders .................................................... 2-45
Sunglasses holder ......................................... 2-47
Glove box ....................................................... 2-47
Console box .................................................... 2-48
Card holder (if so equipped) ........................... 2-49
Storage box (if so equipped) ........................... 2-50>

Black plate (89,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]ZONE VARIATION CHANGE PROCE-
DURE GUID-E09E8E8D-3C27-49AC-9DF4-41F27EDC4D72
The difference between magnetic north and
geographical north is known as variance.
In some areas, this difference can some-
times be great enough to cause false
compass readings. Follow these instruc-
tions to set the variance for your particular
location if this happens:
1. Push the
switch for more than 3
seconds. The current zone number will
appear in the display.
2. Find your current location and variance
number on the zone map.
3. Push the
switch repeatedly until
the new zone number appears in the
display, then release the switch. After
you release the switch, the display will
show a compass direction within a few
seconds. .
If the compass deviates from the
correct indication soon after re-
peated adjustment, have the com-
pass checked at an INFINITI retailer. .
The compass may not indicate the
correct compass point in tunnels or
while driving up or down a steep hill.
(The compass returns to the correct compass point when the vehicle
moves to an area where the geo-
magnetism is stabilized.)
CAUTION . Do not install a ski rack, antenna, etc.,
which are attached to the vehicle by
means of a magnet. They affect the
operation of the compass.
. When cleaning the mirror, use a paper
towel or similar material dampened with
glass cleaner. Do not spray glass cleaner
directly on the mirror as it may cause the
liquid cleaner to enter the mirror hous-
ing.
Instruments and controls
2-11

Black plate (91,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]CAUTION. If the warning light comes on while
driving there may be a malfunction in
the AWD system. Reduce the vehicle
speed and have your vehicle checked by
an INFINITI retailer as soon as possible.
. If the AWD warning light blinks on when
you are driving:
— blinks rapidly (about twice a sec-
ond):
Pull off the road in a safe area, and
idle the engine. The driving mode will
change to 2WD to prevent the AWD
system from malfunctioning. If the
warning light turns off, you can drive
again.
— blinks slowly (about once every 2
seconds):
Pull off the road in a safe area, and
idle the engine. Check that all tire
sizes are the same, tire pressure is
correct and tires are not worn.
. If the warning light is still on after the
above operations, have your vehicle
checked by an INFINITI retailer as soon as possible.
or Anti-lock Braking
System (ABS) warning light GUID-999CB2F5-4FF3-4D41-ACF3-7E00ED4B6C0F
When the ignition switch is in the ON
position, the Anti-lock Braking System
(ABS) warning light illuminates and then
turns off. This indicates the ABS is opera-
tional.
If the ABS warning light illuminates while
the engine is running, or while driving, it
may indicate the ABS is not functioning
properly. Have the system checked by an
INFINITI retailer.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system
then operates normally, but without anti-
lock assistance. (See “ Brake system ” (P.5-
51).)
Automatic transmission check
warning light (if so equipped) GUID-A564A816-81E3-40F1-8684-0ED502ABDB57
When the ignition switch is pushed to the
ON position, the light comes on for 2
seconds. If the light comes on at any other
time, it may indicate the transmission is
not functioning properly. Have your INFINITI
retailer check and repair the transmission. or Brake warning light GUID-9EF95796-7290-4F31-AB06-6BE1BB80003D
This light functions for both the parking
brake and the foot brake systems.
Parking brake indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the ignition switch is in the ON
position, the light comes on when the
parking brake is applied.
Low brake fluid warning light: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the ignition switch is in the ON
position, the light warns of a low brake
fluid level. If the light comes on while the
engine is running with the parking brake
not applied, stop the vehicle and perform
the following:
1. Check the brake fluid level. If brake
fluid is necessary, add fluid and have
the system checked by your INFINITI
retailer. (See “ Brake and clutch fluid ”
(P.8-15).)
2. If the brake fluid level is correct, have
the warning system checked by an
INFINITI retailer.
Anti-lock Braking System (ABS) warning
indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the parking brake is released and
the brake fluid level is sufficient, if both
the brake warning light and the Anti-lock
Instruments and controls
2-13

Black plate (104,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-26 Instruments and controls SIC3264
TRIP COMPUTER GUID-FA55F5BE-A6B8-4E7E-AC55-ED2A35F5EAE6
Switches for the trip computer are located
on the right side of the combination meter
panel. To operate the trip computer, push
the side or front of the switches as shown
above.
* A
switch
* B
switch
When the ignition switch is pushed to the
ON position, modes of the trip computer
can be selected by pushing the
switch
* A
.
Each time the
switch
* A
is pushed, the
display will change as follows: Current fuel consumption ? Average fuel
consumption and speed ? Elapsed time
and trip odometer ? Distance to empty
(dte) ? Outside air temperature (ICY) ?
Setting ? Warning check
1. Current fuel consumption GUID-68872F59-1473-4975-A038-16336C4914A6
The current fuel consumption mode shows
the current fuel consumption.
2. Average fuel consumption (MPG
or l (liter)/100 km) and speed (MPH
or km/h) GUID-970652AF-3316-41FA-92BD-2EBCE8A3AE40
Fuel consumption: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The average fuel consumption mode shows
the average fuel consumption since the
last reset. Resetting is done by pushing the
switch
* B
for longer than 1 second.
(The average speed is also reset at the
same time.)
The display is updated every 30 seconds.
At about the first 1/3 mile (500 m) after a
reset, the display shows “——” .
Speed: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The average speed mode shows the
average vehicle speed since the last reset.
Resetting is done by pushing the
switch
* B
for longer than 1 second. (The average fuel consumption is also reset
at the same time.)
The display is updated every 30 seconds.
The first 30 seconds after a reset, the
display shows “——” .
3. Elapsed time and trip odometer
(mls or km) GUID-30877500-42E1-4C43-AC8D-A3CFB91E6B66
Elapsed time: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The elapsed time mode shows the time
since the last reset. The displayed time can
be reset by pushing the
switch
* B
for
longer than 1 second. (The trip odometer is
also reset at the same time.)
Trip odometer: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The trip odometer mode shows the total
distance the vehicle has been driven since
the last reset. Resetting is done by pushing
the
switch
* B
for longer than 1
second. (The elapsed time is also reset at
the same time.)
4. Distance to empty (dte — mls or
km) GUID-B742AF0B-DD41-497D-AF93-CAE2072D2205
The distance to empty (dte) mode provides
you with an estimation of the distance that
can be driven before refueling. The dte is
constantly being calculated, based on the

Black plate (105,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]amount of fuel in the fuel tank and the
actual fuel consumption.
The display is updated every 30 seconds.
The dte mode includes a low range warning
feature. If the fuel level is low, the warning
is displayed on the screen.
When the fuel level drops even lower, the
dte display will change to “——” .
. If the amount of fuel added is small, the
display just before the ignition switch
is pushed to the OFF position may
continue to be displayed.
. When driving uphill or rounding curves,
the fuel in the tank shifts, which may
momentarily change the display.
5. Outside air temperature (ICY — 8 F
or 8 C) GUID-35621BA5-D61E-4ECD-9628-F300D193449A
The outside air temperature is displayed in
8 F or 8 C in the range of − 22 to 131 8 F ( − 30
to 55 8 C).
The outside air temperature mode includes
a low temperature warning feature. If the
outside air temperature is below 37 8 F
(3 8 C), the warning is displayed on the
screen.
The outside temperature sensor is located
in front of the radiator. The sensor may be affected by road or engine heat, wind
directions and other driving conditions.
The display may differ from the actual
outside temperature or the temperature
displayed on various signs or billboards.
6. Setting GUID-9F18B5C6-F437-4D24-B240-415AA28B0E09
Setting cannot be made while driving. A
message “ Setting can only be operated
when stopped ” is also displayed on the
dot matrix crystal display.
The
switch
* A
and switch
* B
are
used in the setting mode to select and
decide a menu.
SKIP: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Push the switch
* A
to move to the
warning check mode.
Push the
switch
* B
to select other
menus.
ALERT: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 3 submenus under the alert
menu.
. BACK
Select this submenu to return to the top
page of the setting mode.
. TIME TO REST
Select this submenu to specify when the “ time to rest ” indicator activates.
. ICY
Select this submenu to display the low
outside temperature warning.
MAINTENANCE: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 5 submenus under the main-
tenance menu.
. BACK
Select this submenu to return to the top
page of the setting mode.
. ENGINE OIL
Select this submenu to set or reset the
distance for changing the engine oil.
. OIL FILTER
Select this submenu to set or reset the
distance for replacing the oil filter.
. TIRE
Select this submenu to set or reset the
distance for replacing tires.
. OTHER
Select this submenu and set or reset
the distance for replacing items other
than the engine oil, oil filter and tires.
DISPLAY: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
There are 3 submenus under the display
menu.
Instruments and controls
2-27

Black plate (116,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-38 Instruments and controls SIC3270Instrument brightness control GUID-CB95F8CC-B487-4989-8E61-0C52D48B3633
The instrument brightness control switch
can be operated when the ignition switch
is in the ON position. When the switch is
operated, the dot matrix liquid crystal
display switches to the brightness adjust-
ment mode.
Push the upper switch
* A
to brighten the
instrument panel lights. The bar
* 1
moves
to the + side. When reaching the maximum
brightness, “ MAX ” appears on the display
* 2
.
Push the lower switch
* B
to dim the
instrument panel lights. The bar
* 1
moves
to the − side. When reaching the minimum
brightness, “ MIN ” appears on the display
* 3
. However, “ MIN ” does not appear
during the nighttime.
The dot matrix liquid crystal display
returns to the normal display under the
following conditions:
. when the instrument brightness control
switch is not operated for more than 5
seconds.
. when the side or front of the
switch
or
switch on the right side of the
combination meter panel is pushed. SIC3271
TURN SIGNAL SWITCH GUID-8B2C7C5B-C4F7-454D-AF37-BDA58A9D5766
* 1
Turn signal GUID-130C353A-4100-44B3-BC20-735826AC072D
Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signals cancel automati-
cally.
* 2
Lane change signal GUID-4CB70D1F-17E6-4D5C-8884-15EA840D0327
To indicate a lane change, move the lever
up or down to the point where lights begin
flashing.

Black plate (140,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-62 Instruments and controlsPROGRAMMING TROUBLE-DIAGNO-
SIS GUID-D075D2BD-E7C7-474E-83FC-B6F733CCAE46
If HomeLink ®
does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter bat-
teries with new batteries.
. position the hand-held transmitter with
its battery area facing away from the
HomeLink ®
surface.
. push and hold both the HomeLink ®
and
hand-held transmitter buttons without
interruption.
. position the hand-held transmitter 2 to
5 in (50 to 127 mm) away from the
HomeLink ®
surface. Hold the transmit-
ter in that position for up to 15
seconds. If HomeLink ®
is not pro-
grammed within that time, try holding
the transmitter in another position -
keeping the indicator light in view at all
times.
If you continue to have programming
difficulties, please contact the INFINITI
Consumer Affairs Department. The phone
numbers are located in the Foreword of
this Owner ’ s Manual. CLEARING THE PROGRAMMED IN-
FORMATION GUID-93441B3F-2212-4876-94D6-FC87E5157313
Individual buttons cannot be cleared,
however to clear all programming, push
and hold the two outside buttons and
release when the indicator light begins to
flash (in approximately 20 seconds).
REPROGRAMMING A SINGLE
HomeLink ®
BUTTON GUID-F8D4C203-F653-4BE8-9078-5A51BCCE5405
To reprogram a HomeLink ®
Universal
Transceiver button, complete the following.
1. Push and hold the desired HomeLink ®
button. Do not release the button until
step 4 has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to
127 mm) away from the HomeLink ®
surface.
3. Push and hold the hand-held transmit-
ter button.
4. The HomeLink ®
indicator light will
flash, first slowly and then rapidly.
When the indicator light begins to flash
rapidly, release both buttons.
The HomeLink ®
Universal Transceiver but-
ton has now been reprogrammed. The new device can be activated by pushing the
HomeLink ®
button that was just pro-
grammed. This procedure will not affect
any other programmed HomeLink ®
but-
tons.
IF YOUR VEHICLE IS STOLEN GUID-5786CF0E-BD69-4511-B9FA-84F26F89F025
If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into
HomeLink ®
. Consult the Owner ’ s Manual
of each device or call the manufacturer or
retailer of those devices for additional
information.
When your vehicle is recovered, you will
need to reprogram the HomeLink ®
Uni-
versal Transceiver with your new transmit-
ter information.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.

Black plate (201,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]file.
. (Previous)
Select the “
” key to display the
previous file.
Setting the Image Viewer: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The Image Viewer setting display will
appear when selecting the “ Settings ” key
on the full screen display. The following
settings are available for the full screen
display.
. Slideshow Speed
Select the “ Slideshow Speed ” key.
From the following display, select the
changing time from 5, 10, 30, 60
seconds or “ No Auto Change ” .
. Slideshow Order
Select the “ Slideshow Order ” key. From
the following display, select “ Random ”
or “ Order List ” . For “ Order List ” , the
image order is the order of the files as
stored on the USB memory.
Operating tips: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
. Only files that meet the following
conditions will be displayed.
— Image type: JPEG
— File Extensions: *.jpg, *jpeg — Maximum Resolution: 2048 6 1536
pixels
— Maximum Size: 2-MB
— Colors: 32768 (15-bit)
— Maximum File Name lengths: 253-
Bytes
— Maximum Folders: 500
— Maximum Images per Folder: 1024
. If an electronic device (such as a digital
camera) is directly connected to the
vehicle using a USB cable, no image
will be displayed on the screen.
. If the file name is too long, some file
names may not be entirely displayed.
. When the total number of characters in
the file name exceeds 100 or if 1 file
name in a directory exceeds 100
characters, all files will show a shor-
tened 8-character version. The image
will still be displayed when selected. GUID-63214A06-C148-4301-9B23-AF1E0EA151B6
When the selector/shift lever is shifted into
the “ R ” (Reverse) position, the monitor
display shows view to the rear of the
vehicle.
The system is designed as an aid to the
driver in detecting large stationary objects
to help avoid damaging the vehicle. The
system will not detect small objects below
the bumper and may not detect objects
close to the bumper or on the ground.
WARNING . The rearview monitor is a convenience
but it is not a substitute for proper
vehicle operation because it has areas
where objects cannot be viewed. Always
look out the windows and check mirrors
to be sure that it is safe to move before
operating the vehicle. Always operate
the vehicle slowly.
. Objects viewed in the RearView Monitor
differ from actual distance because a
wide-angle lens is used. Objects in the
RearView Monitor will appear visually
opposite like ones viewed in the inside
and outside mirrors.
. Make sure that the trunk is securely
closed when backing up.
Monitor, climate, audio, phone and voice recognition systems
4-23REARVIEW MONITOR (if so equipped)