heater INFINITI M35 2007 Factory Service Manual

ENGINE MAINTENANCE (VK45DE ENGINE)
MA-23
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: 2007 April2007 M35/M45
When draining all of engine coolant in the system, open water drain plugs on cylinder block. Refer
to EM-253, "
DISASSEMBLY" .
4. Remove reservoir tank as necessary, and drain engine coolant and clean reservoir tank before installing.
5. Check drained engine coolant for contaminants such as rust, corrosion or discoloration.
If contaminated, flush the engine cooling system. Refer to MA-24, "
FLUSHING COOLING SYSTEM" .
REFILLING ENGINE COOLANT
1. Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean radiator drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to EM-257,
"ASSEMBLY" .
2. Make sure that each hose clamp has been firmly tightened.
3. Remove air relief plug (1) on heater hose.
4. Fill thermostat housing and reservoir tank to specified level.

Refill engine coolant up to filler neck of thermostat housing.

Pour engine coolant through engine coolant filler neck slowly of less than 2 (2-1/8 US qt, 1-3/4
Imp qt) a minute to allow air in system to escape.

Use genuine NISSAN Long Life Antifreeze/Coolant or equivalent mixed with water (distilled or
demineralized). Refer to MA-12, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
1 : Radiator drain plug hole
2 : Front engine undercover
: Engine front
PBIC3395E
Radiator drain plug:
: 1.2 N·m (0.12 kg-m, 11 in-lb)
: Engine front
PBIC3394E
Engine coolant capacity
(With reservoir tank at “MAX” level):
Approx. 10.4 (11 US qt, 9-1/8 Imp qt)

MA-24
ENGINE MAINTENANCE (VK45DE ENGINE)
Revision: 2007 April2007 M35/M45

When engine coolant overflows air relief hole on heater hose,
install air relief plug.
5. Install radiator cap.
6. Warm up until opening thermostat. Standard for warming-up time is approximately 10 minutes at 3,000
rpm.

Make sure thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.
CAUTION:
Watch water temperature gauge so as not to overheat engine.
7. Stop engine and cool down to less than approximately 50°C (122°F).

Cool down using a fan to reduce the time.

If necessary, refill engine coolant up to filler neck of thermostat housing.
8. Refill reservoir tank to “MAX” level line with engine coolant.
9. Repeat steps 4 through 7 two or more times with radiator cap installed until engine coolant level no longer
drops.
10. Check cooling system for leaks with engine running.
11. Warm up engine, and check for sound of engine coolant flow while running engine from idle up to 3,000
rpm with heater temperature controller set at several position between “COOL” and “WARM”.

Sound may be noticeable at heater unit.
12. Repeat step 11 three times.
13. If sound is heard, bleed air from cooling system by repeating steps 4 through 7 until engine coolant level
no longer drops.
FLUSHING COOLING SYSTEM
1. Install reservoir tank, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plugs on cylinder block are removed, close and tighten them. Refer to EM-257,
"ASSEMBLY" .
2. Remove air relief plug (1) on heater hose.
3. Fill thermostat housing with water until water spills from the air relief hole, then close air relief plug. Fill
thermostat housing and reservoir tank with water and reinstall radiator cap. Reservoir tank engine coolant capacity
(At “MAX” level):
0.8 (7/8 US qt, 3/4 lmp qt)
Air relief plug:
: 1.2 N·m (0.12 kg-m, 11 in-lb)
SMA412B
Radiator drain plug:
: 1.2 N·m (0.12 kg-m, 11 in-lb)
: Engine front
PBIC3394E

HARNESS
PG-95
C
D
E
F
G
H
I
J
L
MA
B
PG
Revision: 2007 April2007 M35/M45
Wiring Diagram Codes (Cell Codes) NKS004ET
Use the chart below to find out what each wiring diagram code stands for.
Refer to the wiring diagram code in the alphabetical index to find the location (page number) of each wiring
diagram.
Code Section Wiring Diagram Name
A/C ATC Air Conditioner
AF1B1 EC Air Fuel Ratio Sensor 1 Bank 1
AF1B2 EC Air Fuel Ratio Sensor 1 Bank 2
AF1HB1 EC Air Fuel Ratio Sensor 1 Heater Bank 1
AF1HB2 EC Air Fuel Ratio Sensor 1 Heater Bank 2
AFS LT Adaptive Front Lighting System
APPS1 EC Accelerator Pedal Position Sensor
APPS2 EC Accelerator Pedal Position Sensor
APPS3 EC Accelerator Pedal Position Sensor
ASC/BS EC Automatic Speed Control Device (ASCD) Brake Switch
ASC/SW EC Automatic Speed Control Device (ASCD) Steering Switch
ASCBOF EC Automatic Speed Control Device (ASCD) Brake Switch
ASCIND EC Automatic Speed Control Device (ASCD) Indicator
AT/IND DI A/T Indicator Lamp
AUT/DP SE Automatic Drive Positioner
AUTO/L LT Automatic Light System
AV AV Audio and Visual System
AWD TF AWD Control System
BACK/L LT Back-Up Lamp
BRK/SW EC Brake Switch
C/SEAT SE Climate Controlled Seat
CAN AT CAN Communication Line
CAN EC CAN Communication Line
CAN LAN CAN System
CHARGE SC Charging System
CHIME DI Warning Chime
CIGAR WW Cigarette Lighter
CLOCK DI Clock
COMBSW LT Combination Switch
COMPAS DI Compass and Thermometer
COOL/F EC Cooling Fan Control
CUR/SE EC Battery Current Sensor
D/LOCK BL Power Door Lock
DEF GW Rear Window Defogger
DTRL LT Headlamp - with Daytime Light System
ECM/PW EC ECM Power Supply for Back-Up
ECTS EC Engine Coolant Temperature Sensor
ENG/ST BL Engine Start System
EPS STC Electric Controlled Power Steering System
ETC1 EC Electric Throttle Control Function
ETC2 EC Electric Throttle Control Motor Relay

PG-96
HARNESS
Revision: 2007 April2007 M35/M45
ETC3 EC Electric Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FPCM EC Fuel Pump Control Module
FTS AT A/T Fluid Temperature Sensor Circuit
FTTS EC Fuel Tank Temperature Sensor
FUELB1 EC Fuel Injection System Function (Bank 1)
FUELB2 EC Fuel Injection System Function (Bank 2)
H/LAMP LT Headlamp
HORN WW Horn
HSEAT SE Heated Seat
I/KEY BL Intelligent Key System
I/MIRR GW Inside Mirror (Auto Anti-Dazzling Mirror)
IATS EC Intake Air Temperature Sensor
ICC ACS Intelligent Cruise Control System
ICC/BS EC ICC Brake Switch
ICC/SW EC ICC Steering Switch
ICCBOF EC ICC Brake Switch
IGNSYS EC Ignition System
ILL LT Illumination
INJECT EC Injector
IVCB1 EC Intake Valve Timing Control Solenoid Valve Bank 1
IVCB2 EC Intake Valve Timing Control Solenoid Valve Bank 2
IVCSB1 EC Intake Valve Timing Control Position Sensor Bank 1
IVCSB2 EC Intake Valve Timing Control Position Sensor Bank 2
IVTB1 EC Intake Valve Timing Control System (Bank 1)
IVTB2 EC Intake Valve Timing Control System (Bank 2)
KS EC Knock Sensor
LDW DI Lane Departure Warning System
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp., Oil and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MMSW AT Manual Mode Switch
NATS BL Nissan Anti-Theft System
NONDTC AT Non-Detective Items
O2H2B1 EC Heated Oxygen Sensor 2 Heater Bank 1
O2H2B2 EC Heated Oxygen Sensor 2 Heater Bank 2
O2S2B1 EC Heated Oxygen Sensor 2 Bank 1
O2S2B2 EC Heated Oxygen Sensor 2 Bank 2
P/SCKT WW Power Socket
PDU PG Power Distribution Unit Code Section Wiring Diagram Name

SE-2Revision: 2007 April2007 M35/M45 Check Reclining Switch Circuit ............................... 71
Check Lifting Switch (Front) Circuit ........................ 73
Check Lifting Switch (Rear) Circuit ......................... 75
Check Power Seat Switch Ground Circuit .............. 76
Check Telescopic Switch Circuit ............................. 77
Check Tilt Switch Circuit ......................................... 79
Check Seat Memory and Set Switch Circuit ........... 81
Check Seat Memory Indicator Lamp Circuit ........... 82
Check Door Mirror Sensor Power Supply and
Ground Circuit ........................................................ 84
Check A/T Device (Detention Switch) Circuit ......... 86
Check Front Door Switch (Driver Side) Circuit ....... 87
Check UART Communication Line Circuit .............. 88
Check Lumbar Support Circuit ............................... 90
POWER SEAT(PASSENGER SIDE) ......................... 92
Schematic ............................................................... 92
Wiring Diagram — SEAT — .................................... 93
POWER SEAT(REAR) .............................................. 96
Component Parts and Harness Connector Location ... 96
System Description ................................................. 96
REAR POWER SEAT LH AND RH OPERATION ... 96
REAR SEAT RETREAT FUNCTION ................... 97
Schematic ............................................................... 98
Wiring Diagram — R/SEAT — ................................ 99
Terminals and Reference Values for Rear Seat Con-
trol Unit .................................................................103
Work Flow .............................................................104
Trouble Diagnoses Symptom Chart ......................104
Check Rear Power Seat Power Supply Circuit .....104
Check Rear Seat Control Unit Power Supply and
Ground Circuit ......................................................105
Check Rear Seat Sliding Motor Circuit .................106
Check Rear Power Seat Switch Circuit ................107
Check Automatic Return Cancel Switch Circuit ....109
Check Automatic Return Cancel Switch ...............110
Check Rear Door Switch Circuit ............................111
Check Rear Seat Sliding Sensor Circuit ...............112
CLIMATE CONTROLLED SEAT .............................114
Component Parts and Harness Connector Location .114
System Description ...............................................114
Schematic .............................................................118
Wiring Diagram — C/SEAT — ..............................119
Terminal and Reference Value for Climate Con-
trolled Seat Control Unit .......................................124
Work Flow .............................................................125
Trouble Diagnoses Symptom Chart ......................126
Preliminary Check ................................................126
Check Climate Controlled Seat Control Unit Power
Supply Circuit .......................................................127
Check Climate Controlled Seat Control Unit Power
Supply and Ground Circuit ...................................128
Check Climate Controlled Seat Switch Power Sup-ply Circuit ..............................................................131
Check Climate Controlled Seat Switch Circuit ......132
Check Climate Controlled Seat Switch Indicator Cir-
cuit ........................................................................134
Check Seat Cushion Thermal Electric Device Cir-
cuit ........................................................................136
Check Seatback Thermal Electric Device Circuit ..137
Check Seat Cushion Thermal Electric Device Sen-
sor Circuit ..............................................................138
Check Seatback Thermal Electric Device Sensor
Circuit ....................................................................140
Check Climate Controlled Seat Blower Motor Circuit .141
Check Climate Controlled Seat Control Unit .........143
HEATED SEAT ........................................................144
Component Parts and Harness Connector Location .144
System Description ...............................................144
Schematic .............................................................146
Wiring Diagram — HSEAT — ...............................147
Terminals and Reference Values for Rear Seat Con-
trol Unit ..................................................................152
Work Flow .............................................................152
Trouble Diagnoses Symptom Chart ......................152
Check Rear Heated Seat Power Supply and Ground
Circuit ....................................................................153
Check Rear Seat Control Unit Power Supply and
Ground Circuit .......................................................154
Check Rear Heated Seat Switch Circuit ...............156
Check Rear Heated Seat Indicator Power Supply
Circuit ....................................................................158
Check Rear Heated Seat Indicator Circuit ............159
Check Rear Heated Seat Circuit ...........................161
Check Rear Seatback Heater Circuit ....................162
FRONT SEAT ..........................................................164
Driver's Seat Components ....................................164
Passenger's Seat Components .............................166
Removal and Installation .......................................168
REMOVAL ..........................................................168
INSTALLATION ..................................................168
Disassembly and Assembly ..................................169
SEATBACK ........................................................169
SEAT CUSHION ................................................170
CLIMATE CONTROLLED SEAT ........................172
REAR SEAT .............................................................173
Bench Seat Components ......................................173
Power Seat (Split Type) Components ...................175
Removal and Installation .......................................177
BENCH SEAT ....................................................177
POWER SEAT ...................................................177
Disassembly and Assembly ..................................178
BENCH SEAT ....................................................178
POWER SEAT ...................................................180

CLIMATE CONTROLLED SEAT
SE-143
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Climate Controlled Seat Control UnitNIS0027Z
1. CHECK THE CLIMATE CONTROLLED SEAT CONTROL UNIT
Does the heater operate normally when the driver side or passenger side climate controlled seat control unit is
exchanged?
YES or NO
YES >> Climate controlled seat control unit is OK.
NO >> Replace climate controlled seat control unit.

HEATED SEAT
SE-145
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
When rear heated seat switch (LH, RH) is LOW position, ground is suppled

to rear seat control unit terminal 18,

through rear heated seat switch terminal 2,

through rear heated seat switch terminal 3,

through body grounds B5, B40 and B131
Then rear seat control unit recognizes that rear heated seat switch is LOW position.
When rear heated seat switch is LOW position, power is supplied

through rear seat control unit terminal 6,

through rear seat cushion heater terminal 2,

through rear seat cushion heater terminal 3,

to rear seatback heater terminal 1.
Then ground is suppled

to rear seatback heater terminal 2.

through body grounds B5, B40 and B131.
With power and ground supplied, rear heated seat is operated.
When rear heated seat switch is in LOW position, ground is supplied

to rear heated seat switch terminal 5,

through rear seat control unit terminal 14,

through rear seat control unit terminal 13,

through body grounds B5, B40 and B131.
With power and ground supplied, rear heated seat switch LOW position indicator is illuminated
When rear heated seat switch (LH, RH) is in HIGH position, ground is suppled

to rear seat control unit terminal 17,

through rear heated seat switch terminal 1,

through rear heated seat switch terminal 3,

through body grounds B5, B40 and B131
Then rear seat control unit recognizes that rear heated seat switch is in HIGH position.
When rear heated seat switch is in HIGH position, power is supplied

through rear seat control unit terminal 5,

through rear seat cushion heater terminal 1,

through rear seat cushion heater terminal 3,

to rear seatback heater terminal 1.
Then ground is suppled

to rear seatback heater terminal 2.

through body grounds B5, B40 and B131.

to rear seat cushion heater terminal 2,

through rear seat control unit terminal 6,

through rear seat control unit terminal 8,

through body grounds B5, B40 and B131.
With power and ground supplied, rear heated seat generates heat more than the time of LOW position.
When rear heated seat switch is in HIGH position, ground is supplied

to rear heated seat switch terminal 4,

through rear seat control unit terminal 9,

through rear seat control unit terminal 13,

through body grounds B5, B40 and B131.
With power and ground supplied rear heated seat switch HIGH position indicator is illuminated.

SE-152
HEATED SEAT
Revision: 2007 April2007 M35/M45
Terminals and Reference Values for Rear Seat Control UnitNIS00284
Work FlowNIS00285
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to SE-144, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to SE-152,
"Trouble Diagnoses Symptom Chart" .
4. Does heated seat operate normally? YES: GO TO 5, NO: GO TO 3.
5. INSPECTION END.
Trouble Diagnoses Symptom ChartNIS00286

Check that other systems using the signal of the following systems operate normally.
TerminalWire
colorItemSignal
Input/OutputConditionVoltage (V)
(Approx.)
1 R Power source (BAT) Input — Battery voltage
4 R/B Power source (IGN) Input — Battery voltage
5 R/Y Seat heater HI signal InputSeat heater HI operation Battery voltage
Other than above 0
6 R/L Seat heater LO signal InputSeat heater LO operation Battery voltage
Other than above 0
8 B/L Ground (power) — — 0
9 W/B Heated seat indicator HI signal OutputHeater HI operation (lit) 0
Other than above Battery voltage
13 B/Y Ground (signal) — — 0
14 W/G Heated seat indicator LO signal OutputHeater LO operation (lit) 0
Other than above Battery voltage
17 W/L Heated seat switch HI signal InputHeated seat switch (HI) – ON (pressed) 0
Heated seat switch (HI) – OFF Battery voltage
18 W Heated seat switch LO signal InputHeated seat switch (LO) – ON (pressed) 0
Heated seat switch (LO) – OFF Battery voltage
Symptom Diagnoses / service procedure Refer to page
Rear heated seat LH and RH does not operate.Check rear heated seat power supply and ground
circuitSE-153
Rear heated seat LH or RH do not operate.1. Check rear seat control unit power supply and
ground circuitSE-1542. Check rear heated seat switch circuit SE-156
3. Check rear seatback heater circuit SE-162
4. Replace rear LH or RH seat control unitSE-144
Rear heated seat do not operate with LO or HI position.1. Check rear heated seat switch circuitSE-1562. Check rear heated seat circuitSE-161
Rear heated seat LH or RH indicator do not operate.Check rear heated seat indicator power supply
circuit SE-158
Rear heated seat indicator do not operate with LO or HI position Check rear heated seat indicator circuit SE-159

HEATED SEAT
SE-161
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Rear Heated Seat CircuitNIS0028C
1. CHECK REAR SEAT CONTROL UNIT
1. Turn ignition switch ON.
2. Check voltage between rear seat control unit connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Replace rear seat control unit.
2. CHECK REAR SEAT HEATER HARNESS
1. Turn ignition switch OFF.
2. Disconnect rear seat control unit and rear seat cushion heater connector.
3. Check continuity between rear seat control unit connector and
rear seat cushion heater connector.
4. Check continuity between rear seat control unit connector and
ground.
OK or NG
OK >> GO TO 3.
NG >> Replace or replace harness between rear seat control unit and rear seat cushion heater.
Te r m i n a l
ConditionVoltage (V)
(Approx.) (+)
(–) Rear seat
control unit
connectorTe r m i n a l
B303 (LH)
B353 (RH)5
GroundRear heated
seat switchHIGH Battery voltage
Other than above. 0
6Rear heated
seat switchLOW Battery voltage
Other than above. 0
PIIB6010E
AB
Continuity
Rear seat control
unit connectorTerminalRear seat cushion
heater connectorTerminal
B303 (LH)
B353 (RH)5
B309 (LH)
B359 (RH)1
Ye s
62
A
GroundContinuity
Rear seat control
unit connectorTerminal
B303 (LH)
B353 (RH)5
No
6
PIIB6011E

SE-162
HEATED SEAT
Revision: 2007 April2007 M35/M45
3. CHECK REAR SEAT HEATER CIRCUIT
1. Connect rear seat control unit and rear seat cushion heater connector.
2. Turn ignition switch ON.
3. Check voltage between rear seat cushion heater connector and
ground.
OK or NG
OK >> Check the condition of the harness and connector.
NG >> Replace rear seat cushion heater.
Check Rear Seatback Heater CircuitNIS0028D
1. CHECK REAR SEAT HEATER CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between rear seat cushion heater connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Replace rear seat cushion heater.
Terminal
ConditionVoltage (V)
(Approx.) (+)
(–) Rear seat
cushion heater
connectorTerminal
B309 (LH)
B359 (RH)3 GroundRear heated
seat switchHIGH Battery voltage
LOW 6
Other than above. 0
PIIB6012E
Terminal
ConditionVoltage (V)
(Approx.) (+)
(–) Rear seat
cushion heater
connectorTerminal
B309 (LH)
B359 (RH)3 GroundRear heated
seat switchHIGH Battery voltage
LOW 6
Other than above. 0
PIIB6012E