climate control INFINITI M35 2007 Factory User Guide

PERIODIC MAINTENANCE
MA-9
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: 2007 April2007 M35/M45
(2) If operating mainly in dusty conditions, more frequent maintenance may be required.
(3) Maintenance-free item. For service procedures, refer to FL section.
(4) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months.
(5) If valve noise increases, inspect valve clearance.
* Maintenance items and intervals with “*” are recommended by INFINITI for reliable vehicle operation. The owner need not perform
such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are
required.
CHASSIS AND BODY MAINTENANCE
Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary.
NOTE:
(1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) fluid (A/T, trans-
fer)/oil at every 30,000 miles (48,000 km) or 24 months. Using automatic transmission fluid other than Genuine NISSAN Matic J
ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmis-
sion, which is not covered by the INFINITI new vehicle limited warranty.
(2) Refer to “Tire rotation” under the “GENERAL MAINTENANCE” heading earlier in this section.MAINTENANCE OPERATIONMAINTENANCE INTERVAL
Reference
Section -
Page or -
Content Title Perform at number of miles,
kilometers or months,
whichever comes first.Miles x 1,000
(km x 1,000)
Months3.75
(6)
37.50
(12)
611 . 2 5
(18)
915
(24)
1218.75
(30)
1522.5
(36)
1826.25
(42)
2130
(48)
24
Brake lines & cables I IMA-35
Brake pads & rotors I I I IMA-36
Automatic transmission &
transfer fluid & differential
gear oilNOTE (1) I IMA-29,
MA-31
,
MA-32
Steering gear, linkage &
transfer gear, axle & sus-
pension partsIIIIMA-36,
MA-37
Tire rotation NOTE (2)MA-4,
MA-35
Drive shaft boots and pro-
peller shaft (AWD models) IIIIMA-38,
MA-32
Exhaust system I I I IMA-29
In-cabin microfilter R RAT C - 1 3 3
Climate controlled seat filterRSE-172
MAINTENANCE OPERATIONMAINTENANCE INTERVAL
Reference
Section -
Page or -
Content Title Perform at number of miles,
kilometers or months,
whichever comes first.Miles x 1,000
(km x 1,000)
Months33.75
(54)
2737.5
(60)
3041.25
(66)
3345
(72)
3648.75
(78)
3952.5
(84)
4256.25
(90)
4560
(96)
48
Brake lines & cables I IMA-35
Brake pads & rotors I I I IMA-36
Automatic transmission &
transfer fluid & differential
gear oilNOTE (1) I IMA-29,
MA-31
,
MA-32
Steering gear, linkage &
transfer gear, axle & sus-
pension partsI IIIMA-36,
MA-37
Tire rotation NOTE (2)MA-4,
MA-35
Drive shaft boots and pro-
peller shaft (AWD models)I IIIMA-38,
MA-32
Exhaust system I I I IMA-29
In-cabin microfilter R RAT C - 1 3 3
Climate controlled seat filterRSE-172

PERIODIC MAINTENANCE
MA-11
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: 2007 April2007 M35/M45
NOTE:
(1) Refer to “Tire rotation” under the “GENERAL MAINTENANCE” heading earlier in this section.In-cabin microfilter R R R RAT C - 1 3 3
Climate controlled seat filter R RSE-172
MAINTENANCE OPERATIONMAINTENANCE INTERVAL
Reference Sec-
tion - Page or -
Content Title Perform at number of miles, kilo-
meters or months, whichever
comes first.Miles x 1,000
(km x 1,000)
Months7.5
(12)
615
(24)
1222.5
(36)
1830
(48)
2437.5
(60)
3045
(72)
3652.5
(84)
4260
(96)
48

HARNESS
PG-95
C
D
E
F
G
H
I
J
L
MA
B
PG
Revision: 2007 April2007 M35/M45
Wiring Diagram Codes (Cell Codes) NKS004ET
Use the chart below to find out what each wiring diagram code stands for.
Refer to the wiring diagram code in the alphabetical index to find the location (page number) of each wiring
diagram.
Code Section Wiring Diagram Name
A/C ATC Air Conditioner
AF1B1 EC Air Fuel Ratio Sensor 1 Bank 1
AF1B2 EC Air Fuel Ratio Sensor 1 Bank 2
AF1HB1 EC Air Fuel Ratio Sensor 1 Heater Bank 1
AF1HB2 EC Air Fuel Ratio Sensor 1 Heater Bank 2
AFS LT Adaptive Front Lighting System
APPS1 EC Accelerator Pedal Position Sensor
APPS2 EC Accelerator Pedal Position Sensor
APPS3 EC Accelerator Pedal Position Sensor
ASC/BS EC Automatic Speed Control Device (ASCD) Brake Switch
ASC/SW EC Automatic Speed Control Device (ASCD) Steering Switch
ASCBOF EC Automatic Speed Control Device (ASCD) Brake Switch
ASCIND EC Automatic Speed Control Device (ASCD) Indicator
AT/IND DI A/T Indicator Lamp
AUT/DP SE Automatic Drive Positioner
AUTO/L LT Automatic Light System
AV AV Audio and Visual System
AWD TF AWD Control System
BACK/L LT Back-Up Lamp
BRK/SW EC Brake Switch
C/SEAT SE Climate Controlled Seat
CAN AT CAN Communication Line
CAN EC CAN Communication Line
CAN LAN CAN System
CHARGE SC Charging System
CHIME DI Warning Chime
CIGAR WW Cigarette Lighter
CLOCK DI Clock
COMBSW LT Combination Switch
COMPAS DI Compass and Thermometer
COOL/F EC Cooling Fan Control
CUR/SE EC Battery Current Sensor
D/LOCK BL Power Door Lock
DEF GW Rear Window Defogger
DTRL LT Headlamp - with Daytime Light System
ECM/PW EC ECM Power Supply for Back-Up
ECTS EC Engine Coolant Temperature Sensor
ENG/ST BL Engine Start System
EPS STC Electric Controlled Power Steering System
ETC1 EC Electric Throttle Control Function
ETC2 EC Electric Throttle Control Motor Relay

SE-2Revision: 2007 April2007 M35/M45 Check Reclining Switch Circuit ............................... 71
Check Lifting Switch (Front) Circuit ........................ 73
Check Lifting Switch (Rear) Circuit ......................... 75
Check Power Seat Switch Ground Circuit .............. 76
Check Telescopic Switch Circuit ............................. 77
Check Tilt Switch Circuit ......................................... 79
Check Seat Memory and Set Switch Circuit ........... 81
Check Seat Memory Indicator Lamp Circuit ........... 82
Check Door Mirror Sensor Power Supply and
Ground Circuit ........................................................ 84
Check A/T Device (Detention Switch) Circuit ......... 86
Check Front Door Switch (Driver Side) Circuit ....... 87
Check UART Communication Line Circuit .............. 88
Check Lumbar Support Circuit ............................... 90
POWER SEAT(PASSENGER SIDE) ......................... 92
Schematic ............................................................... 92
Wiring Diagram — SEAT — .................................... 93
POWER SEAT(REAR) .............................................. 96
Component Parts and Harness Connector Location ... 96
System Description ................................................. 96
REAR POWER SEAT LH AND RH OPERATION ... 96
REAR SEAT RETREAT FUNCTION ................... 97
Schematic ............................................................... 98
Wiring Diagram — R/SEAT — ................................ 99
Terminals and Reference Values for Rear Seat Con-
trol Unit .................................................................103
Work Flow .............................................................104
Trouble Diagnoses Symptom Chart ......................104
Check Rear Power Seat Power Supply Circuit .....104
Check Rear Seat Control Unit Power Supply and
Ground Circuit ......................................................105
Check Rear Seat Sliding Motor Circuit .................106
Check Rear Power Seat Switch Circuit ................107
Check Automatic Return Cancel Switch Circuit ....109
Check Automatic Return Cancel Switch ...............110
Check Rear Door Switch Circuit ............................111
Check Rear Seat Sliding Sensor Circuit ...............112
CLIMATE CONTROLLED SEAT .............................114
Component Parts and Harness Connector Location .114
System Description ...............................................114
Schematic .............................................................118
Wiring Diagram — C/SEAT — ..............................119
Terminal and Reference Value for Climate Con-
trolled Seat Control Unit .......................................124
Work Flow .............................................................125
Trouble Diagnoses Symptom Chart ......................126
Preliminary Check ................................................126
Check Climate Controlled Seat Control Unit Power
Supply Circuit .......................................................127
Check Climate Controlled Seat Control Unit Power
Supply and Ground Circuit ...................................128
Check Climate Controlled Seat Switch Power Sup-ply Circuit ..............................................................131
Check Climate Controlled Seat Switch Circuit ......132
Check Climate Controlled Seat Switch Indicator Cir-
cuit ........................................................................134
Check Seat Cushion Thermal Electric Device Cir-
cuit ........................................................................136
Check Seatback Thermal Electric Device Circuit ..137
Check Seat Cushion Thermal Electric Device Sen-
sor Circuit ..............................................................138
Check Seatback Thermal Electric Device Sensor
Circuit ....................................................................140
Check Climate Controlled Seat Blower Motor Circuit .141
Check Climate Controlled Seat Control Unit .........143
HEATED SEAT ........................................................144
Component Parts and Harness Connector Location .144
System Description ...............................................144
Schematic .............................................................146
Wiring Diagram — HSEAT — ...............................147
Terminals and Reference Values for Rear Seat Con-
trol Unit ..................................................................152
Work Flow .............................................................152
Trouble Diagnoses Symptom Chart ......................152
Check Rear Heated Seat Power Supply and Ground
Circuit ....................................................................153
Check Rear Seat Control Unit Power Supply and
Ground Circuit .......................................................154
Check Rear Heated Seat Switch Circuit ...............156
Check Rear Heated Seat Indicator Power Supply
Circuit ....................................................................158
Check Rear Heated Seat Indicator Circuit ............159
Check Rear Heated Seat Circuit ...........................161
Check Rear Seatback Heater Circuit ....................162
FRONT SEAT ..........................................................164
Driver's Seat Components ....................................164
Passenger's Seat Components .............................166
Removal and Installation .......................................168
REMOVAL ..........................................................168
INSTALLATION ..................................................168
Disassembly and Assembly ..................................169
SEATBACK ........................................................169
SEAT CUSHION ................................................170
CLIMATE CONTROLLED SEAT ........................172
REAR SEAT .............................................................173
Bench Seat Components ......................................173
Power Seat (Split Type) Components ...................175
Removal and Installation .......................................177
BENCH SEAT ....................................................177
POWER SEAT ...................................................177
Disassembly and Assembly ..................................178
BENCH SEAT ....................................................178
POWER SEAT ...................................................180

SE-114
CLIMATE CONTROLLED SEAT
Revision: 2007 April2007 M35/M45
CLIMATE CONTROLLED SEATPFP:870U6
Component Parts and Harness Connector LocationNIS0027H
System DescriptionNIS0027I
The climate controlled seat system is controlled by climate controlled seat control unit.
Heating and cooling are possible for a thermal electric device (heat conversion machine).
NOTE:

The climate controlled seat system is downed when the temperature sensor set as the seat cushion and
the seat back's thermal electric device machine detects 20 °C (68 °F)or more of mutual differences of tem-
perature.

In this case, by turning off ignition switch, system down is canceled and it can be reused by turning on
ignition switch again.

The climate controlled seat blower keep low speed for approximately 60 seconds after turning the climate
controlled seat switch.
CAUTION:

The thermal electric device has the character in which, as for an opposite side. one side becomes
high temperature at the time of low temperature.
PIIB5891E
1. Fuse block (J/B) 2. Climate controlled seat relay E16 3.a: Climate controlled seat switch
driver side B430
b: Climate controlled seat switch
passenger side B429
4.a: Seat cushion thermal electric
device B285 (driver side)
B295 (passenger side)
b: Climate controlled seat control
unit B283, B284 (driver side)
B293, B294 (passenger side)
c: Climate controlled seat blower
motor B282 (driver side)
B292 (passenger side)5.Seatback thermal electric device
B220 (driver side)
B258 (passenger side)

CLIMATE CONTROLLED SEAT
SE-115
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45

At the time of work, please turn OFF a switch, and carry it out after checking that the thermal elec-
tric device has got cold.
Power is at all times supplied

through 15A fuse [No. 41 located in the fuse fusible link and relay unit]

to climate controlled seat relay terminals 5.

through 15A fuse [No. 42 located in the fuse fusible link and relay unit]

to climate controlled seat relay terminals 7.
When the ignition switch turned to ON or START position,
Power is supplied

through 10A fuse [No. 12, located in the fuse block (J/B)]

to climate controlled seat relay terminal 2.
Then ground is supplied

to climate controlled seat relay terminal 1,

through body grounds E22 and E43.
Then climate controlled seat relay is energized.
When climate controlled seat relay is turned to ON,
Power is supplied,

through climate controlled seat relay terminal 3,

to climate controlled seat control unit (passenger side) terminal 2 and 4.

through climate controlled seat relay terminal 6,

to climate controlled seat control unit (driver side) terminal 2 and 4.
When climate controlled switch select HEAT, ground is supplied

through climate controlled seat switch terminal 1 and 3,

to climate controlled seat control unit terminal 10.
Then, the climate controlled seat control unit receives climate controlled seat switch HEAT signal.
When climate controlled seat switch select COOL, ground is supplied

through climate controlled seat switch terminal 1 and 2,

to climate controlled seat control unit terminal 20,
Then, the climate controlled seat control unit receives climate controlled switch COOL signal.
When blower motor rotates, signal is transmitted

to climate controlled seat control unit terminal 18,

through climate controlled seat blower motor terminal 1.
This is climate controlled seat blower motor tachometer signal.
When climate controlled seat control unit receives climate controlled seat switch signal and tachometer signal,
Power is supplied

to climate controlled seat blower motor terminal 4,

through climate controlled seat control unit terminal 17.
This is blower motor revolution control signal.
When blower motor receivers blower motor revolution control signal,
Power is supplied

through climate controlled seat control unit terminal 14,

to climate controlled seat blower motor terminal 2.
When number of rotations correspond signal,
Ground is supplied

to climate controlled seat blower motor terminal 3,

through climate controlled seat control unit terminal 7,

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
Then motor revolution is controlled.
When the ignition switch turned to ON or START position,
Power is supplied

SE-116
CLIMATE CONTROLLED SEAT
Revision: 2007 April2007 M35/M45

to seat cushion thermal electric device terminal 1,

through climate controlled seat control unit terminal 22.
Then ground is supplied

to climate controlled seat control unit terminal 21,

through seat cushion thermal electric device terminal 2,
Then the climate controlled seat control unit recognizes seat cushion thermal electric device sensor signal.
When climate controlled seat control unit recognizes climate controlled seat switch HEAT signal and, seat
cushion thermal electric device sensor signal,
Power is supplied

to seat cushion thermal electric device terminal 4,

through climate controlled seat control unit terminal 5.
Then ground is supplied

through seat cushion thermal electric device terminal 6,

to climate controlled seat control unit terminal 6,

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
When climate controlled seat control unit recognizes climate controlled seat switch COOL signal and seat
cushion thermal electric device sensor signal,
Power is supplied

to seat cushion thermal electric device terminal 6,

through climate controlled seat control unit terminal 6.
Then ground is supplied

through seat cushion thermal electric device terminal 4,

to climate controlled seat control unit terminal 5.

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
When the ignition switch turned to ON or START position,
Power is supplied

to seatback thermal electric device terminal 1,

through climate controlled seat control unit terminal 23.
Then ground is supplied

to climate controlled seat control unit terminal 24,

through seatback thermal electric device terminal 2,

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
Then the climate controlled seat control unit recognizes seatback thermal electric device sensor signal.
When climate controlled seat control unit recognizes climate controlled seat switch HEAT signal and seatback
thermal electric device sensor signal,
Power is supplied

to seatback thermal electric device terminal 4,

through climate controlled seat control unit terminal 15,
ground is supplied

to climate controlled seat control unit terminal 16,

through seatback thermal electric device terminal 6,

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
This seatback thermal electric device generates heat wind is warmed.
When climate controlled seat control unit recognizes climate controlled seat switch COOL signal and seatback
thermal electric device sensor signal,
Power is supplied

to seatback thermal electric device terminal 6,

CLIMATE CONTROLLED SEAT
SE-117
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45

through climate controlled seat control unit terminal 16,
ground is supplied

to climate controlled seat control unit terminal 15,

through seatback thermal electric device terminal 4,

through climate controlled seat control unit terminal 3,

through body grounds B5, B40 and B131.
When climate controlled switch selects HEAT,
Power is supplied

to climate controlled seat switch terminal 5,

through climate controlled seat control unit terminal 8.
Ground is supplied

to the climate controlled seat switch terminal 6,

through body grounds B402 and B405.
Then climate controlled seat switch HEAT indicator is energized.
When climate controlled switch select COOL,
Power is supplied

to climate controlled seat switch terminal 4,

through climate controlled seat control unit terminal 9.
Ground is supplied

to the climate controlled seat switch terminal 6,

through body grounds B402 and B405.
Then climate controlled seat switch COOL indicator is energized.

SE-118
CLIMATE CONTROLLED SEAT
Revision: 2007 April2007 M35/M45
SchematicNIS0027J
TIWT1391E

CLIMATE CONTROLLED SEAT
SE-119
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Wiring Diagram — C/SEAT — NIS0027K
TIWT2129E