display INFINITI M35 2007 Factory Owner's Manual

ACS-50
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 13 STOP LAMP RLY FIXNKS004D7
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “STOP LAMP RLY FIX [C1A13]” (DTC 13)
is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK CONNECTOR FOR ECM
1. Turn ignition switch OFF.
2. Disconnect ECM connector, and connect it securely again.
3. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
4. Check if “STOP LAMP RLY FIX [C1A13]” (DTC 13) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> GO TO 3.
NO >> Poor connector connection
1. Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.)
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
3. CHECK STOP LAMP SWITCH WITH ICC DATA MONITOR
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “STOP LAMP SW” operates normally.
OK or NG
OK >> GO TO 11.
NG >> GO TO 4.
4. CHECK STOP LAMP SWITCH INSTALLATION AND ADJUSTMENT
Check stop lamp switch for proper installation, and adjust the switch if necessary. Refer to BR-6, "
BRAKE
PEDAL" .
OK or NG
OK >> GO TO 5.
NG >> 1. Adjust stop lamp switch.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
5. CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to ACS-69, "
ICC Brake Switch and Stop Lamp Switch" .
OK or NG
OK >> GO TO 6.
NG >> 1. Replace stop lamp switch.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

ACS-56
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
23. CHECK HARNESS BETWEEN STOP LAMP SWITCH AND ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT)
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check continuity between stop lamp switch harness connector
(A) and ABS actuator and electric unit (control unit) harness
connector (B).
4. Check continuity between stop lamp switch harness connector
(A) and ground.
OK or NG
OK >> 1. Perform “ABS” self-diagnosis. Refer to BRC-23, "CONSULT-II Functions (ABS)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Repair or replace harness between stop lamp switch and ABS actuator and electric unit (control
unit).
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 14 ECM CIRCUITNKS004D8
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “ECM CIRCUIT [C1A14]” (DTC 14) is indi-
cated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. PERFORM ECM SELF-DIAGNOSIS
With CONSULT-II
1. Perform “ENGINE” self-diagnosis. Refer to EC-123, "
CONSULT-II Function (ENGINE)" (for VQ35DE) or
EC-826, "
CONSULT-II Function (ENGINE)" (for VK45DE).
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
AB
Continuity
Connector Terminal Connector Terminal
E124 4 E30 30 Yes
A
GroundContinuity
Connector Terminal
E124 4 No
PKIC0834E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
DTC 15 GEAR POSITIONNKS004D9
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “VHCL SPEED SE CIRC [C1A03]” (DTC 3), “ABS/TCS/VDC CIRC [C1A04]” (DTC 4) or “CAN
COMM CIRCUIT [U1000]” (DTC100) other than “GEAR POSITION [C1A15]” (DTC 15) is indicated in self-
diagnosis item in the display.
Is any indicated?
YES >> 1. Repair or replace applicable item. Refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. CHECK VEHICLE SPEED SIGNAL
With CONSULT-II
With “ICC” “DATA MONITOR”, check if “VHCL SPEED SE” operates normally.
OK or NG
OK >> GO TO 3.
NG >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
3. CHECK SHIFT GEAR POSITION
Check if gear positions are correct in A/T.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II
With “A/T” “DATA MONITOR”, check if gear positions are correct.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE REVOLUTION
With CONSULT-II
With TCM diagnosis, check if turbine revolution sensor is normal. Refer to AT- 11 7 , "
DTC P0717 TURBINE
REVOLUTION SENSOR" .
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.

ACS-58
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 16 RADAR STAINNKS004DA
1. VISUAL INSPECTION 1
Check ICC sensor integrated unit body window for contamination and foreign materials.
Is it found?
YES >> 1. If any, remove them.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 2.
2. VISUAL INSPECTION 2
Check ICC sensor integrated unit body window for cracks and scratches.
Is it found?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 3.
3. ASKING COMPLAINTS
1. Ask if there is any trace of contamination or foreign material on ICC sensor integrated unit.
2. Ask if vehicle was driven in snow or ICC sensor integrated unit was frosted.
3. Ask if ICC sensor integrated unit was fogged temporarily. (Front window glass may have also tended to be
fogged.)
Is there any symptom?
YES >> Explain difference in displays between contamination detection result and current indication to
customer, and tell them “This is not malfunction”.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 18 LASER AIMING INCMPNKS004DB
1. ADJUST LASER BEAM AIMING
1. Adjust laser beam aiming. Refer to ACS-15, "
LASER BEAM AIMING ADJUSTMENT" .
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
3. Check if “LASER AIMING INCMP [C1A18]” (DTC 18) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> INSPECTION END
DTC 21 UNIT HIGH TEMPNKS004DC
1. CHECK SYMPTOM
Check if cooling system malfunctions.
Does it malfunction?
YES >> 1. Repair cooling system.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-59
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
DTC 24 NP RANGENKS004DD
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC100) other than “NP RANGE [C1A24]” (DTC 24) is indi-
cated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK TCM DATA MONITOR
With CONSULT-II
With “A/T” “DATA MONITOR” check if gear positions are correct.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
DTC 25 SHIFT RANGE INDNKS004DE
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “SHIFT RANGE IND [C1A25]” (DTC 25) is
indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK TCM DATA MONITOR
With CONSULT-II
With “A/T” “DATA MONITOR”, check if gear positions are correct.
OK or NG
OK >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NG >> 1. Perform “A/T” self-diagnosis. Refer to AT- 9 0 , "
CONSULT-II Function (A/T)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.

ACS-60
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2007 April2007 M35/M45
DTC 26 ECD MODE MALFNKS004DF
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “ECD MODE MALF [C1A26]” (DTC 26) is
indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-II
1. Perform “ABS” self-diagnosis. Refer to BRC-23, "
CONSULT-II Functions (ABS)" .
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
DTC 27 ECD PWR SUPLY CIRNKS004DG
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis.
2. Check if “CAN COMM CIRCUIT [U1000]” (DTC 100) other than “ECD PWR SUPLY CIR [C1A27]” (DTC
27) is indicated in self-diagnosis item in the display.
Is it indicated?
YES >> 1. CAN communication inspection. Refer to ACS-61, "DTC 100 CAN COMM CIRCUIT" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY CIRCUIT
With CONSULT-II
Check ABS actuator and electric unit (control unit) power supply circuit. Refer to BRC-37, "
ABS Actuator and
Electric Unit (Control Unit) Power Supply and Ground Circuit" .
OK or NG
OK >> 1. Perform “ABS” self-diagnosis. Refer to BRC-23, "CONSULT-II Functions (ABS)" .
2. After repairing or replacing applicable item, erase DTC and perform ICC system running test.
Then perform self-diagnosis of ICC system again.
NG >> 1. Repair or replace applicable item.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-61
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
DTC 100 CAN COMM CIRCUITNKS004DH
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
1. Perform self-diagnosis.
2. Print self-diagnostic result.
>> After printing self-diagnostic result, go to “CAN system”. Refer to LAN-42, "
Precautions When
Using CONSULT-II" .
DTC 110 CONTROL UNIT (CAN)NKS004DI
1. PERFORM ICC SENSOR INTEGRATED UNIT SELF-DIAGNOSIS
With CONSULT-II
1. Perform self-diagnosis.
2. Print self-diagnostic result.
3. Erase DTC and perform ICC running test. Then perform self-diagnosis of ICC system again.
4. Check if “CONTROL UNIT (CAN) [U1010]” (DTC 110) is indicated in self-diagnosis item in the display.
Is malfunction indicated?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> INSPECTION END

ACS-62
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2007 April2007 M35/M45
TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Symptom ChartNKS004DJ
Symptoms Reference page
OperationMAIN switch does not switch ON.Symptom 1
ACS-63
MAIN switch does not switch OFF.Symptom 1
ACS-63
Cruise does not function for setting (powering functions).Symptom 2
ACS-64
CANCEL switch does not function.Symptom 3
ACS-65
Resume does not function.Symptom 3
ACS-65
Set speed does not increase.Symptom 3
ACS-65
Set distance to the vehicle ahead cannot be changed.Symptom 3
ACS-65
ICC is not cancelled when the A/T selector lever is in other than
“D” and “M”.Symptom 4
ACS-65
Display/ChimeDot matrix LCD does not appear.Check combination meter. Refer to DI-18, "Trouble Diagnosis" .
Chime does not function.Symptom 5
ACS-66
Control Driving force is hunting.Symptom 6
ACS-67
Function to detect
the vehicle aheadSystem frequently cannot detect the vehicle ahead.Symptom 7
ACS-67
Distance to detect the vehicle ahead is short.Symptom 7
ACS-67
System misidentifies a vehicle even though there is no vehicle
ahead.

Refer to ACS-15, "LASER BEAM AIMING
ADJUSTMENT" .

Refer to ACS-12, "ICC System Running
Te s t" .
System misidentifies a vehicle in the next lane.

Refer to ACS-15, "LASER BEAM AIMING
ADJUSTMENT" .

Refer to ACS-12, "ICC System Running
Te s t" .
System does not detect a vehicle at all.Symptom 8
ACS-68

ACS-68
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2007 April2007 M35/M45
3. ADJUST LASER BEAM AIMING
1. Adjust laser beam aiming. Refer to ACS-15, "
LASER BEAM AIMING ADJUSTMENT" .
2. Perform ICC system running test. Check if preceding vehicle detection performance has been improved.
Is it improved?
YES >> INSPECTION END
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at AllNKS004DR
1. CHECK DISPLAY
Check if dot matrix LCD in the combination meter illuminate. Refer to DI-17, "
Self-Diagnosis Mode of Combi-
nation Meter" .
OK or NG
OK >> GO TO 2.
NG >> Check combination meter. Refer to DI-18, "
HOW TO PERFORM TROUBLE DIAGNOSIS"
2. VISUAL CHECK 1
Check ICC sensor integrated unit body window for contamination and foreign materials.
Is it found?
YES >> 1. If any, remove them.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 3.
3. VISUAL CHECK 2
Check ICC sensor integrated unit body window for cracks and scratches.
Is it found?
YES >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.
NO >> GO TO 4.
4. ADJUST LASER BEAM AIMING
1. Adjust laser beam aiming. Refer to ACS-15, "
LASER BEAM AIMING ADJUSTMENT" .
2. Perform ICC system running test. Check if preceding vehicle detection performance has been improved.
Is it improved?
YES >> INSPECTION END
NO >> 1. Replace ICC sensor integrated unit, and adjust laser beam aiming.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

INDEX FOR DTC
AT-5
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
INDEX FOR DTCPFP:00024
Alphabetical Index NCS001JA
NOTE:
If DTC “U1000” is displayed with other DTC, first perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION LINE”. Refer to AT- 1 0 5
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.Items
(CONSULT-II screen terms)DTC
Reference page OBD-II Except OBD-II
CONSULT-II
GST (*1) CONSULT-II only “A/T”
A/T 1ST E/BRAKING — P1731AT-145
ATF PRES SW 1/CIRC — P1841AT-172
ATF PRES SW 3/CIRC — P1843AT-174
ATF PRES SW 5/CIRC — P1845AT-176
ATF PRES SW 6/CIRC — P1846AT-178
A/T INTERLOCK P1730 P1730AT-142
A/T TCC S/V FNCTN P0744 P0744 AT-128
ATF TEMP SEN/CIRC P0710 P1710AT-135
CAN COMM CIRCUIT U1000 U1000AT-105
D/C SOLENOID/CIRC P1762 P1762AT-155
D/C SOLENOID FNCTN P1764 P1764 AT-157
ENGINE SPEED SIG P0725 (*2) P0725AT-124
FR/B SOLENOID/CIRC P1757 P1757AT-151
FR/B SOLENOID FNCT P1759 P1759 AT-153
HLR/C SOL/CIRC P1767 P1767AT-159
HLR/C SOL FNCTN P1769 P1769 AT-161
I/C SOLENOID/CIRC P1752 P1752AT-147
I/C SOLENOID FNCTN P1754 P1754 AT-149
L/PRESS SOL/CIRC P0745 P0745AT-130
LC/B SOLENOID/CIRC P1772 P1772AT-163
LC/B SOLENOID FNCT P1774 P1774 AT-165
MANU MODE SW/CIRC — P1815AT-167
PNP SW/CIRC P0705 P0705AT- 11 3
STARTER RELAY/CIRC — P0615AT-108
TCC SOLENOID/CIRC P0740 P0740AT-126
TCM P0700 P0700AT- 11 2
TP SEN/CIRC A/T P1705 (*2) P1705AT-132
TURBINE REV S/CIRC P0717 P0717AT- 11 7
VEH SPD SE/CIR·MTR — P1721AT-140
VEH SPD SEN/CIR AT P0720 P0720AT- 11 9