clutch INFINITI M35 2007 Factory Owner's Guide

TROUBLE DIAGNOSIS
AT-45
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
A/T Interlock

If there is an A/T interlock judgment malfunction, the A/T is fixed in 2nd gear to make driving possible.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine revolution sensor malfunction.

When the coupling pattern below is detected, the fail-safe action corresponding to the pattern is per-
formed.
A/T INTERLOCK COUPLING PATTERN TABLE

: NG X: OK
A/T 1st Engine Braking

When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is
switched OFF to avoid the engine brake operation.
Line Pressure Solenoid

The solenoid is switched OFF and the line pressure is set to the maximum hydraulic pressure to make
driving possible.
Torque Converter Clutch Solenoid

The solenoid is switched OFF to release the lock-up.
Low Coast Brake Solenoid

When a malfunction (electrical or functional) occurs, in order to make driving possible. If the solenoid is
ON, the A/T is held in 2nd gear. If the solenoid is OFF, the A/T is held in 4th gear. (Engine brake is not
applied in 1st and 2nd gear.)
Input Clutch Solenoid

If a malfunction (electrical or functional) occurs with the solenoid either ON or OFF, the A/T is held in 4th
gear to make driving possible.
Direct Clutch Solenoid

If a malfunction (electrical or functional) occurs with the solenoid either ON or OFF, the A/T is held in 4th
gear to make driving possible.
Front Brake Solenoid

If a malfunction (electrical or functional) occurs with the solenoid ON, in order to make driving possible.
The A/T is held in 5th gear. If the solenoid is OFF, the A/T is 4th gear.
High and Low Reverse Clutch Solenoid

If a (electrical or functional) malfunction occurs with the solenoid either ON or OFF, the A/T is held in 4th
gear to make driving possible.
Turbine Revolution Sensor 1 or 2

The control is the same as if there were no turbine revolution sensors, 5th gear and manual mode are pro-
hibited.
Gear positionATF pressure switch output
Fail-safe
functionClutch pressure output pattern after fail-safe func-
tion
SW3
(I/C)SW6
(HLR/
C)SW5
(D/C)SW1
(FR/B)SW2
(LC/B)I/C HLR/C D/C FR/B LC/B L/U
A/T inter-
lock cou-
pling pattern3rd – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
4th – X X –
Held in
2nd gearOFF OFF ON OFF OFF OFF
5th X X – X
Held in
2nd gearOFF OFF ON OFF OFF OFF

AT-48
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
DIAGNOSTIC WORKSHEET
Information from Customer
KEY POINTS

WHAT..... Vehicle and A/T model

WHEN..... Date, Frequencies

WHERE..... Road conditions

HOW..... Operating conditions, Symptoms
Diagnostic Worksheet Chart
Customer name MR/MS Model and Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequency❏ Continuous❏ Intermittent ( times a day)
Symptoms❏ Vehicle does not move. (❏ Any position❏ Particular position)
❏ No up-shift (❏ 1st → 2nd❏ 2nd → 3rd❏ 3rd → 4th ❏ 4th → 5th)
❏ No down-shift (❏ 5th → 4th ❏ 4th → 3rd❏ 3rd → 2nd❏ 2nd → 1st)
❏ Lock-up malfunction
❏ Shift point too high or too low.
❏ Shift shock or slip (❏ N → D❏ N → R❏ Lock-up❏ Any drive position)
❏ Noise or vibration
❏ No kick down
❏ No pattern select
❏ Others
()
A/T CHECK indicator lamp❏ Continuously lit❏ Not lit
Malfunction indicator lamp (MIL)❏ Continuously lit❏ Not lit
1❏ Read the item on cautions concerning fail-safe and understand the customer's complaint.AT- 4 4
2❏ A/T fluid inspectionAT- 5 3❏ Leak (Repair leak location.)
❏ State
❏ Amount
3❏ Stall test and line pressure testAT- 5 3
, AT-
55❏ Stall test
❏ Torque converter one-way clutch
❏ Front brake
❏ High and low reverse clutch
❏ Low coast brake
❏ Forward brake
❏ Reverse brake
❏ Forward one-way clutch❏ 1st one-way clutch
❏ 3rd one-way clutch
❏ Engine
❏ Line pressure low
❏ Except for input clutch and direct
clutch, clutches and brakes OK
❏ Line pressure inspection - Suspected part:

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
4❏ Perform all road tests and enter checks in required inspection items.AT- 5 7
4-1.Check before engine is started AT- 5 7
❏ AT- 1 9 0 , "A/T CHECK Indicator Lamp Does Not Come On"
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 2 ,AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE"
❏ AT-108, "DTC P0615 START SIGNAL CIRCUIT"
❏ AT-112, "DTC P0700 TCM"
❏ AT-113, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT-117, "DTC P0717 TURBINE REVOLUTION SENSOR"
❏ AT-119, "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT-124, "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT-126, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT-128, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT-130, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT-132, "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT-135, "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT-140, "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT-142, "DTC P1730 A/T INTERLOCK"
❏ AT-145, "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT-147, "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT-149, "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-151, "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT-153, "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT-155, "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT-157, "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-159, "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT-161, "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT-163, "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT-165, "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT-167, "DTC P1815 MANUAL MODE SWITCH"
❏ AT-172, "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT-174, "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT-176, "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT-178, "DTC P1846 ATF PRESSURE SWITCH 6"
4-2.Check at IdleAT- 5 7
❏ AT- 1 9 0 , "Engine Cannot Be Started in “P” or “N” Position"
❏ AT- 1 9 1 , "In “P” Position, Vehicle Moves When Pushed"
❏ AT- 1 9 2 , "In “N” Position, Vehicle Moves"
❏ AT- 1 9 3 , "Large Shock (“N” to “D” Position)"
❏ AT- 1 9 5 , "Vehicle Does Not Creep Backward in “R” Position"
❏ AT- 1 9 7 , "Vehicle Does Not Creep Forward in “D” Position"
4-3.Cruise TestAT- 5 9
Part 1
❏ AT- 1 9 9 , "
Vehicle Cannot Be Started from D1"
❏ AT- 2 0 1 , "A/T Does Not Shift: D1 → D2"
❏ AT- 2 0 3 , "A/T Does Not Shift: D2 → D3"
❏ AT- 2 0 5 , "A/T Does Not Shift: D3 → D4"
❏ AT- 2 0 7 , "A/T Does Not Shift: D4 → D5"
❏ AT- 2 0 9 , "A/T Does Not Lock-up"
❏ AT- 2 1 0 , "A/T Does Not Hold Lock-up Condition"
❏ AT- 2 1 2 , "Lock-up Is Not Released"
❏ AT- 2 1 2 , "Engine Speed Does Not Return to Idle"

AT-50
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
44-3Part 2AT- 6 1
❏ AT-199, "Vehicle Cannot Be Started from D1"
❏ AT-201, "A/T Does Not Shift: D1 → D2"
❏ AT-203, "A/T Does Not Shift: D2 → D3"
❏ AT-205, "A/T Does Not Shift: D3 → D4"
Part 3AT- 6 1
❏ AT-213, "Cannot Be Changed to Manual Mode"
❏ AT-214, "A/T Does Not Shift: 5th Gear → 4th Gear"
❏ AT-215, "A/T Does Not Shift: 4th Gear → 3rd Gear"
❏ AT-217, "A/T Does Not Shift: 3rd Gear → 2nd Gear"
❏ AT-218, "A/T Does Not Shift: 2nd Gear → 1st Gear"
❏ AT-220, "Vehicle Does Not Decelerate by Engine Brake"
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 2 , AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE"
❏ AT-108, "DTC P0615 START SIGNAL CIRCUIT"
❏ AT- 11 2 , "DTC P0700 TCM"
❏ AT- 11 3 , "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ AT- 11 7 , "DTC P0717 TURBINE REVOLUTION SENSOR"
❏ AT- 11 9 , "DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)"
❏ AT-124, "DTC P0725 ENGINE SPEED SIGNAL"
❏ AT-126, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ AT-128, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ AT-130, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ AT-132, "DTC P1705 THROTTLE POSITION SENSOR"
❏ AT-135, "DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT"
❏ AT-140, "DTC P1721 VEHICLE SPEED SENSOR MTR"
❏ AT-142, "DTC P1730 A/T INTERLOCK"
❏ AT-145, "DTC P1731 A/T 1ST ENGINE BRAKING"
❏ AT-147, "DTC P1752 INPUT CLUTCH SOLENOID VALVE"
❏ AT-149, "DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-151, "DTC P1757 FRONT BRAKE SOLENOID VALVE"
❏ AT-153, "DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION"
❏ AT-155, "DTC P1762 DIRECT CLUTCH SOLENOID VALVE"
❏ AT-157, "DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION"
❏ AT-159, "DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE"
❏ AT-161, "DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION"
❏ AT-163, "DTC P1772 LOW COAST BRAKE SOLENOID VALVE"
❏ AT-165, "DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION"
❏ AT-167, "DTC P1815 MANUAL MODE SWITCH"
❏ AT-172, "DTC P1841 ATF PRESSURE SWITCH 1"
❏ AT-174, "DTC P1843 ATF PRESSURE SWITCH 3"
❏ AT-176, "DTC P1845 ATF PRESSURE SWITCH 5"
❏ AT-178, "DTC P1846 ATF PRESSURE SWITCH 6"
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunctioning parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 5 7
7❏ For any remaining NG items, perform the “Diagnostics Procedure” and repair or replace the malfunctioning
parts. See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection pro-
cedures.)AT- 6 4
8❏ Erase the results of the self-diagnostics from the TCM.AT- 9 6, AT-
104

TROUBLE DIAGNOSIS
AT-53
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
Inspections before Trouble DiagnosisNCS001K7
A/T FLUID CHECK
A/T Fluid Leakage and A/T Fluid Level Check
Inspect for A/T fluid leakage and check the A/T fluid level. Refer to AT- 1 3 , "Checking A/T Fluid" .
A/T Fluid Condition Check
Inspect the A/T fluid condition.
STALL TEST
Stall Test Procedure
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle so that the A/
T fluid temperature is 50 to 80°C (122 to 176°F). Inspect the
amount of ATF. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Engine start, apply foot brake, and place selector lever in “D”
position.
Fluid condition Conceivable Cause Required Operation
Varnished (viscous
varnish state)Clutch, brake
scorchedReplace the ATF and check the A/T
main unit and the vehicle for mal-
functions (wire harnesses, cooler
pipes, etc.)
Milky white or cloudy Water in the fluidReplace the ATF and check for
places where water is getting in.
Large amount of metal
powder mixed inUnusual wear of
sliding parts within
A/TReplace the ATF and check for
improper operation of the A/T.
SAT638A
SAT647B
SCIA7463E
SCIA6787E

AT-54
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
5. While holding down the foot brake, gradually press down the
accelerator pedal.
6. Quickly read off the stall speed, then quickly remove your foot
from the accelerator pedal.
CAUTION:
Do not hold down the accelerator pedal for more than 5 sec-
onds during this test.
7. Move the selector lever to the “N” position.
8. Cool down the ATF.
CAUTION:
Run the engine at idle for at least 1 minute.
9. Repeat steps 5 through 8 with selector lever in “R” position.
Judgement of Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value positionStall speed
VQ35DE models: 2,650 - 2,950 rpm
VK45DE models: 2,260 - 2,560 rpm
SAT514G
SCIA6788E
Selector lever position
Possible location of malfunction
“D”, “M” “R”
Stall speed HO

Forward brake

Forward one-way clutch

1st one-way clutch

3rd one-way clutch
OH

Reverse brake
LL

Engine and torque converter one-way clutch
HH

Line pressure low
Does not shift-up “D” or “M” position 1 → 2 Slipping in 2nd, 3rd or 4th gear Direct clutch slippage
Does not shift-up “D” or “M” position 2 → 3 Slipping in 3rd, 4th or 5th gear High and low reverse clutch slippage
Does not shift-up “D” or “M” position 3 → 4 Slipping in 4th or 5th gear Input clutch slippage
Does not shift-up “D” or “M” position 4 → 5 Slipping in 5th gear Front brake slippage

TROUBLE DIAGNOSIS
AT-65
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
2
Shift
ShockShock is too large
when changing D1 →
D
2 or M1 → M2 .ON vehicle1. Accelerator pedal position sensorAT-132
2. A/T positionAT-227
3. ATF pressure switch 5 and direct clutch solenoid valveAT-176,
AT-155
4. CAN communication lineAT-105
5. Engine speed signalAT-124
6. Turbine revolution sensorAT- 11 7
7. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
8. A/T fluid level and stateAT- 5 3
9. Control valve with TCMAT-236
OFF vehicle 10. Direct clutchAT-341
3Shock is too large
when changing D2 →
D
3 or M2 → M3 .ON vehicle1. Accelerator pedal position sensorAT-132
2. A/T positionAT-227
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT-178,
AT-159
4. CAN communication lineAT-105
5. Engine speed signalAT-124
6. Turbine revolution sensorAT- 11 7
7. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
8. A/T fluid level and stateAT- 5 3
9. Control valve with TCMAT-236
OFF vehicle 10. High and low reverse clutchAT-339
4Shock is too large
when changing D3 →
D
4 or M3 → M4 .ON vehicle1. Accelerator pedal position sensorAT-132
2. A/T positionAT-227
3. ATF pressure switch 3 and input clutch solenoid valveAT-174,
AT-147
4. CAN communication lineAT-105
5. Engine speed signalAT-124
6. Turbine revolution sensorAT- 11 7
7. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
8. A/T fluid level and stateAT- 5 3
9. Control valve with TCMAT-236
OFF vehicle 10. Input clutchAT-327
No. Item Symptom Condition Diagnostic ItemReference
page

AT-66
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
5
Shift
ShockShock is too large
when changing D4 →
D
5 or M4 → M5 .ON vehicle1. Accelerator pedal position sensorAT- 1 3 2
2. A/T positionAT- 2 2 7
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 2,
AT- 1 5 1

4. CAN communication lineAT- 1 0 5
5. Engine speed signalAT- 1 2 4
6. Turbine revolution sensorAT- 11 7
7. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0
8. A/T fluid level and stateAT- 5 3
9. Control valve with TCMAT- 2 3 6
OFF vehicle10. Front brake (brake band)AT- 3 0 111. Input clutchAT- 3 2 7
6Shock is too large for
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT- 1 3 2
2. A/T positionAT- 2 2 7
3. CAN communication lineAT- 1 0 5
4. Engine speed signalAT- 1 2 4
5. Turbine revolution sensorAT- 11 7
6. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0
7. A/T fluid level and stateAT- 5 3
8. Control valve with TCMAT- 2 3 6
OFF vehicle9. Front brake (brake band)AT- 3 0 110. Input clutch AT- 3 2 7
11. High and low reverse clutchAT- 3 3 9
12. Direct clutchAT- 3 4 1
7Shock is too large for
upshift when acceler-
ator pedal is released.ON vehicle1. Accelerator pedal position sensorAT- 1 3 2
2. A/T positionAT- 2 2 7
3. Engine speed signalAT- 1 2 4
4. CAN communication lineAT- 1 0 5
5. Turbine revolution sensorAT- 11 7
6. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0
7. A/T fluid level and stateAT- 5 3
8. Control valve with TCMAT- 2 3 6
OFF vehicle9. Front brake (brake band)AT- 3 0 110. Input clutch AT- 3 2 7
11. High and low reverse clutch AT- 3 3 9
12. Direct clutch AT- 3 4 1
No. Item Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-67
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
8
Shift
ShockShock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT-132
2. A/T positionAT-227
3. Engine speed signalAT-124
4. CAN communication lineAT-105
5. Turbine revolution sensorAT- 11 7
6. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
7. Torque converter clutch solenoid valveAT-126
8. A/T fluid level and stateAT- 5 3
9. Control valve with TCMAT-236
OFF vehicle 10. Torque converterAT-301
9Shock is too large
during engine brake.ON vehicle1. Accelerator pedal position sensorAT-132
2. A/T positionAT-227
3. CAN communication lineAT-105
4. A/T fluid level and stateAT- 5 3
5. Control valve with TCMAT-236
OFF vehicle6. Front brake (brake band)AT-3017. Input clutch AT-327
8. High and low reverse clutchAT-339
9. Direct clutch AT-341
10
No Up
ShiftGear does not change
from D
1 → D2 or from
M
1 → M2 .
Refer to AT-201, "
A/T
Does Not Shift: D1 →
D2" .ON vehicle1. A/T fluid level and stateAT- 5 3
2. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
3. ATF pressure switch 5 and direct clutch solenoid valveAT-176,
AT-155
4. Line pressure testAT- 5 5
5. CAN communication lineAT-105
6. Control valve with TCMAT-236
OFF vehicle 7. Direct clutchAT-341
11Gear does not change
from D
2 → D3 or from
M
2 → M3 .
Refer to AT-203, "
A/T
Does Not Shift: D2 →
D3" .ON vehicle1. A/T fluid level and stateAT- 5 3
2. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT-140
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT-178,
AT-159
4. Line pressure testAT- 5 5
5. CAN communication lineAT-105
6. Control valve with TCMAT-236
OFF vehicle 7. High and low reverse clutchAT-339
No. Item Symptom Condition Diagnostic ItemReference
page

AT-68
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
12
No Up
ShiftGear does not change
from D
3 → D4 or from
M
3 → M4 .
Refer to AT-205, "
A/T
Does Not Shift: D3 →
D4" .ON vehicle1. A/T fluid level and stateAT- 5 3
2. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 4,
AT- 1 4 7
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 2,
AT- 1 5 1
5. Line pressure testAT- 5 5
6. CAN communication lineAT- 1 0 5
7. Control valve with TCMAT- 2 3 6
OFF vehicle 8. Input clutchAT- 3 2 7
13Gear does not change
from D
4 → D5 or from
M
4 → M5 .
Refer to AT-207, "
A/T
Does Not Shift: D4 →
D5" .ON vehicle1. A/T fluid level and stateAT- 5 3
2. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 2,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 7 6,
AT- 1 5 5
5. Turbine revolution sensorAT- 11 7
6. Line pressure testAT- 5 5
7. CAN communication lineAT- 1 0 5
8. Control valve with TCMAT- 2 3 6
OFF vehicle9. Front brake (brake band)AT- 3 0 110. Input clutchAT- 3 2 7
14No Down
ShiftIn “D” or “M” position,
does not downshift to
4th gear.ON vehicle1. A/T fluid level and stateAT- 5 3
2. Vehicle speed sensor·A/T and vehicle speed sensor·MTRAT- 11 9,
AT- 1 4 0

3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 2
,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 7 6,
AT- 1 5 5
5. CAN communication lineAT- 1 0 5
6. Line pressure testAT- 5 5
7. Control valve with TCMAT- 2 3 6
OFF vehicle8. Front brake (brake band)AT- 3 0 19. Input clutchAT- 3 2 7
No. Item Symptom Condition Diagnostic ItemReference
page